BMW ENET data cable OBD2 to ethernet

[@RadimE91]

Hey, I have a problem with this. Seems ISTA/laptop doesnt even notice the cable is plugged in. :/

[@imwmanish]

Thanks for sharing

[@TheAkNas]

Sometimes wire won't stick to obd2 pins when soldering, and overall the wires snap very easily for some reason... Did you have problems making the cable?

[@hassankhalil401]

I know its late , but use flux

[@kennyfixgarage5150]

Thanks mate 🙏. This just helped me after buying a fake cable and i had to rewire it again. 👍

[@mrfixpl]

Happy to help!

[@SkySurferSGC]

Is this cable compatible with e92 01.2008?

[@mrfixpl]

Only for the CIC navi unit.

[@motorcyc1]

I have a 2013 f25. Are you saying to just plug it in and I don't require enet driver download? Thank you

[@mrfixpl]

It doesn’t require drivers since it’s a standard Ethernet connection. You need to configure your LAN card for proper communication.

[@motorcyc1]

Thank you for your quick response! Can you elaborate a little more on how to configure the system? .

[@alfistasubbie]

Nice video, it would be more helpful if you can tell which pins on the RJ-45 connector side (has 8 pins and ethernet cable has 4 pairs) are those 4 wires connected to, without that info, not sure if it is helpful enough.

[@zWhiteWolfy]

I managed to get a glimpse of the cable, he's using T-568A standard Ethernet cable

[@Luca_Techy]

Hi there! I don't suppose the E81 Late 2008 has ENET already? Cheers for the info!

[@mrfixpl]

I believe that only if your E81 is equipped with CIC navigation you'll be able to connect with ENET cable. But it will connect only with the navi unit. For the rest of modules you would need K+DCAN interface.

[@mrfixpl]

In the video I'm testing it in E84 (so not Fxx model) but with said CIC navigation.

[@johnnyzarrrriiizony07L]

Already have two of this with Full Esys software :)

[@mrfixpl]

First time that I needed to extract something from the car and needed to make one. Luckily it’s easy to make and I had all the gear needed. Apart from the Ethernet cable, which has a broken locking pin and I need to hold it in my computer with one hand when operating FTP with the other 😂

[@s1krrpilot]

@@mrfixpl ooooooo so your using a shell to do this

[@ukasz3375]

Czy można i jeśli tak, to: 1. Na którym pinie zastosować diodę led, tak aby po podpięciu interfejsu ENET do gniazda OBD auta stale świeciła sygnalizując połączenie urządzenia z autem ? 2. Czy na którymś pinie można również zastosować diodę led sygnalizującą transfer danych, tj szybkie miganie w trakcie diagnostyki itd ? 3. Czy klasa przewodu Ethernet ma znaczenie w działaniu interfejsu z autem? Mój interfejs ENET ma przewód klasy 6 (CAT6). Wiem, że jest on technicznie lepszy i wydajnieszy od CAT5. Jednak czy ma to znaczenie w prpgeamowaniu, kodowaniu i diagnostyce? Bardzo proszę o odpowiedź. Bardzo mi na tym zależy, aby mieć w zasięgu wzroku taki szybki "swietlny pewnik" działania sprzętu z autem. Oczywiście diody led bezpiecznie usytuowane w obudowie interfejsu.

[@TheWuzyy]

does this work on an E60 Diesel?

[@mrfixpl]

F-series with exception of communication with iDrive CIC system alone in some E-Series.

[@rafus1200]

where are the polish subtitles ?

[@mrfixpl]

Just checked and you should see them 🤔 Make sure you have CC enabled and set to Polish.

[@ArsenBotman]

Hi, any idea about BMW X3 G01 enet cable? I bought the Yellow one, but no communication

[@jdl4502]

Czy moge sie połączyć z BMW serii Exx (E90/E91) ???

[@mrfixpl]

Z tego co wiem, to dopiero serie F miała komunikację w tym standardzie. Za wyjątkiem późnych modelu E (np. E84), gdzie można było się połączyć przez to z systemem navi.

[@jdl4502]

@@mrfixpl dzięki za info. Poszperałem i też tak piszą

[@taunevimdal]

i dot shure... OBD2 connector is male or female? ....thx ;)

[@twertogzun]

Can i code with bimmer link ?could you answer?

[@canakbas3783]

Great sharing... Thanks a lot

[@hanimansour8378]

helo..Does it work on bmw x3 2013For ABS coding

[@rayflexentertainment1545]

can this work for VW?

[@mrfixpl]

Sorry, no. In VW you can use OBDeleven.

[@swistak483]

Where can I dowland bimmercode for my laptop ?

[@thevoiceland]

Does this method works on elm 327 wifi to us it to connect to vw?

[@mrfixpl]

This is for BMW only. And not all of them but those rather new ones (Fxx series and some Exx). But in VW you can use software like Carista for some advanced diagnostics and modifications using ELM327 interface.

[@thevoiceland]

@@mrfixpl Caristaapp doesn't support my vw polo 9n vivo 2014

[@mrfixpl]

Then you can go with OBDeleven but you'll need hardware from them as well as the app for you phone.

[@marcinw2183]

W jaki sposób uruchamiasz aplikacje do kodowania czy diagnostyki na macu? Przez wirtualną maszynę?

[@mrfixpl]

Ta aplikacja to zwykły klient FTP.

[@9-and-3]

Is there a way to find out the ip of the car?

[@mrfixpl]

Should be available at 169.254.199.99

[@9-and-3]

@@mrfixpl Many thanks for your reply. Just bare with me that I got it right :). So I connect my PC to the car (any car compatible with enet) using the enet cable. I set my ethernet interface to a static ip from the subnet 169.254.0.0 255.255.0.0 and then I'm able to access the car via the ip 169.254.199.199?

[@mrfixpl]

Set your PC to IP: 169.254.199.98, subnet: 255.255.255.0, Gateway: 169.254.199.99 You are now connected to cars network. You can access CIC at ftp://169.254.199.99 (login: root; password: Hm83stN or cic0803).

[@qwertyqwerty-zi6dr]

Can u help me ? I want to use xdelete on my 435d where should i connect the cable?

[@TheTheaterdreamer]

Pretty useless without the wiring connections on the rj45 side

[@mrfixpl]

What do you mean? RJ45 goes into your LAN card and that’s it.

[@kidda74]

Hey I just bought the correct cable but how do I get it to connect to the car please? bmw f30

[@Bemaritohtori]

For this cable E-SYS or ISTA is the software you would want with your F-Series

[@caroltdbgu5941]

does it work on volvo v40 2017 ? or is there a diagram for making a cablke like that for it ?

[@SwedenMade]

A v40 does not use this protocol,

[@mustaphaessahihi1762]

Hi does ENET Cable works with e-series?

[@Semihbou]

As I know you need a k+dcan cable for e series

[@und4287]

Only for few models (such as E84), and only for communicating with CIC navi. For other modules you need a K+DCAN cable.

[@eduardoandrade6019]

Hi thanks for sharing, after I build the enet cable do I need some kind of drivers like USB cables? Thanks

[@mrfixpl]

No, this connects to your network connector and does not require any special drivers to work.

[@NN-oy8ru]

Is this cable compatible with e90 05.2010, CIC with small screen?

[@mrfixpl]

AFAIK it will be compatible with E90 CIC but CIC only. There's no access to the rest of the Exx car though this cable.

[@Kilohercas]

fake video. CAN and Ethernet is two different protocols, you need special adapter for that.

[@mrfixpl]

CAN-BUS uses 2 pins from the 16-pin connector. Other than power, ground and 2 other communication standards, car manufacturers are free to use the connector how ever they want to. Do your research.

[@bimmercodingaustria]

@Linas K This works only on F series

[@mrfixpl]

...and some late E-series cars as well. It works in E84 with CIC navigation.

[@akshitmandaviya164]

@@mrfixpl hey Man. ignore that person comment. Your comment is right.

[@s1krrpilot]

@@mrfixpl whats about the mcp2515 chip to communicate with the can bus system

[@richhooker1263]

Hello and thank you for sharing. Any chance you know the wiring configuration for a 2013 bmw 750Li (f02) (N63Tu engine) obd to ethernet cableb for using ista d, ista p and WinKFP software (WinKFP acronym may be wrong but i am referring to the bmw programming software for any in depth programming or coding that does not use ista p or ista D) I purchased what i was told is A BMW icom cable that is good for “iCOM A2” interface as well as “iCOM NEXT” interface. The obd to ethernet pin wiring i have on my cable is slightly different than what you have here in your video… I have Pin 1 blank Pin 2 blank Pin 3 orange wire alone Pin 4 and pin 5 are jumped together but Pin5 has green wire with white stripe soldered to it also. Pin 6 blank Pin 7 blank Pin 8 has 507 ohm resistor soldered to pin 16 Pin 9 blank Pin 10 blank Pin 11 orange wire with white stripe alone Pin 12 blue wire alone Pin 13 green wire alone Pin 14 blank Pin 15 blank Pin 16 has the 507 ohm resistor soldered to pin 8 Is it possible that you have the enet cable and i have the icom cable? Or is my cable just wrong possibly? Any help or insight would be much appreciated! Curious, what is the name of the wire you are making here in this video? Sorry for the long message!