i'm not sure how many are in use, but I have seen a contractor here in Michigan that uses what might be a older version. It uses a separate power unit and is run via hydraulic lines too it. Mostly where might be too swampy too get a regular machine into. Very neat seeing the videos.
@garywells10814 жыл бұрын
I operate a jt30 all terrain and there fun when you figure out what your doing out here in Arizona we got a lot of rock so it some what a pain in the ass when you drill into rock then a few rods later your in dirt so you have to pull out a put the other housing on love it ahaha
@MTIEQUIPMENT4 жыл бұрын
Wow! That does sound like a pain Gary. Sounds like you're pretty experienced and skilled though, which makes you a hot commodity, the industry needs more skilled drillers like you. Thanks for sharing!
@garywells10814 жыл бұрын
@@MTIEQUIPMENT thank you I’ve been drilling for a few years out there in Florida there is a driller named dale Campbell he showed me everything I know
@carlostena71792 жыл бұрын
Hello Carlos Tena here ,I myself love to drill as well I operate a 20/22 Vermeer. I’ve worked in Utha west Texas and east Texas. Looking for new adventures so if anyone needs an Operador let me know .
@ايمنالتركي-و9د Жыл бұрын
مرحبا
@adamwilborn38597 жыл бұрын
ok i run one of those drills and how you steer it is that there is a controller and i mean its like a hand held controller that has a joystick in the middle to maneuver the drill and how you pitch the drill there are levers just beside the control panel that lets you pitch the drill at any angle and there are levers to put the feet down to get a even better pitch
@ايمنالتركي-و9د Жыл бұрын
هل يوجد دروس ع الخاص لي تعليم التشغيل
@evilmindful5 жыл бұрын
Let say something. Please.dont rotate the rods on the green grippers cause you finish the grip and the rods will slide forward and you will have to constantly be changing them or hooking up to then again and again
@TdrT-jp6qmАй бұрын
S.o.p,, add duct tape to each one,,or lower the rear once you start your pilot
@DiHandley4 жыл бұрын
An impressive bit of gear! I’m assuming this is in Australia. Ditch Witch is an Australian product, correct?
@MTIEQUIPMENT4 жыл бұрын
Hi David. Nope Ditch Witch is company out of Perry Oklahoma. Our facility is located in North Port, Florida USA
@TdrT-jp6qmАй бұрын
Charles machine works
@evilmindful5 жыл бұрын
You do have to rotates rods to screww on to the rod so u dont affect the threading but do all
@Sunilkumar-il9tb4 жыл бұрын
How much cost full set Tull and all sports vehicle
@davidowusu22852 жыл бұрын
Very nice,please how much? I really need it👌👌
@MTIEQUIPMENT2 жыл бұрын
Hi David. Thank you for reaching out. This is quite an old video so this machine is not available. To check out current inventory visit www.mtiequip.com
@KC8EWU6 жыл бұрын
Is that one able too be propelled from the operators seat or how do you propel the machine?
@MTIEQUIPMENT6 жыл бұрын
Hey Tony, there are controls at the back of the machine to be able to move the machine around. One smaller rigs you can't drive them around from the operators station.
@andrewndiritu77183 жыл бұрын
Can it drill vertical blast holes?
@rajeshaer7 жыл бұрын
how do you steer and pitch the drill?
@MTIEQUIPMENT7 жыл бұрын
Hey Rajesh! Thanks for watching our video. Are you talking about driving and positioning the rig or do you mean as your drilling how do you steer the rod?
@rajeshaer7 жыл бұрын
MTIEQUIPMENT , I meant the drill bit.it seems like a solid metal pipe and wonder how u manoeuvre?
@heaviernicolas8 жыл бұрын
What are the ditch witch capabilities performing directional boring along a curve? I'm trying to understand how contractors install utilities when approaching a cul-de-sac.
@wall2wall9598 жыл бұрын
it's a little over 100ft to achieve a bend radius on this size pipe
@drakemeaux72705 жыл бұрын
If u have the right driller and locator u can make a cul-de-sac shot in one shot
@TdrT-jp6qmАй бұрын
At rods don't flex much
@antoniofontesbarrosjr48104 жыл бұрын
Dear Sirs , I saw a video of you And I realized that the drill turns but the drill bit pipe does not turn, what equipment do you use before the drill bit?
@MTIEQUIPMENT4 жыл бұрын
Hi Antonio! This is a rockmaster. It's a special housing and bit that is utilized by All Terrain machines that specialize in drilling through rock. The drill pipe features an inner and outer rod. The outer part of the housing is shaped to help steer while the inner pipe turns the tri-cone bit.
@antoniofontesbarrosjr48104 жыл бұрын
@@MTIEQUIPMENT Thank you
@lubisbull34786 жыл бұрын
That was amazing..
@adamwilborn38597 жыл бұрын
and to maneuver the bit it has a inner rod and a outer rod system the inner rod eats the dirt and rock and the outer rod is what turns it
@drakemeaux72705 жыл бұрын
Rock drilling?
@digitalguruchandan4 жыл бұрын
How to operate it
@mohamedzandar67788 жыл бұрын
merci beaucoup pour l'inormation
@larrypacio68756 жыл бұрын
How to apply in your company?
@MTIEQUIPMENT6 жыл бұрын
Hi Larry! Thank you for reaching out. If you would like to see the current positions we are looking to fill and apply, visit www.mtiequip.com/about-us/ and scroll down below the headshots and you will see a box join our team.
@alisarbest27755 жыл бұрын
سلام عليكم ابحث حفارة أفقي ان يكون قوة قابل 60 طن سحب