Multiplexer Simulation using NI Multisim

[@abdurrashidsawom1629]

you reduce my blood pressure. thank you brother......

[@Raghavendraraop]

Welcome..:)

[@chaduvulapujitha4365]

Thankyou sir for your explanation

[@nanagogo7832]

Thanks for the vid! I couldnt hear what you said about A and B. A is less significant than B??

[@Raghavendraraop]

No. I told A is Least Significant Bit (LSB) which means when you take binary equivalent of any number, lets say 2, B=1, A=0, so it is 10 corresponding to decimal 2

[@nanagogo7832]

@@Raghavendraraop thanks a lot for the clarification :)

[@콩물국수-u7o]

정말 좋은 강의였습니다 감사합니다 MULTISIM을 처음하는데 어떻게 도구를 찾아야 할지 몰랐는데 이 영상을보고 많이 배워갑니다.

[@Raghavendraraop]

Thank you..:)

[@ektasharma183]

Hi sir, can you please show simulation of a simple switched capacitor circuit. If possible please use 4066 switch.

[@aayashmishra1305]

Helped a Lot

[@eraserhead205]

Can you explain how to connect the logic converter and generate a truth table?

[@Raghavendraraop]

place the logic converter. There will be 9 pins out of which from the left 8 are inputs (marked as A,B,C till H) and last pin is the output. You can select the number of inputs by clicking on the input circles inside logic converter. Now take any gate with any number of inputs less than 8. Connect the inputs of the TTL gate to the inputs of logic converter. Connect the output of the gate to the last pin of the logic converter. Run the simulation. You will observe the output logic for all the input combinations. Hope I have answered your question

[@eraserhead205]

@@Raghavendraraop Thank you!

[@kimtutv491]

WHERE CAN I CONNECT THE OSCILLOSCOPE?

[@10_madenurindracahyanta55]

thanks rao

[@Raghavendraraop]

Welcome.. :)

[@zackhaziq1116]

hi I want to ask about my simulation. my equation is F(w,x,y,z) = (0,3,5,6,8,9,14,15). and I must use multiplexer circuit using 74151 multiplexer and I can use logic gates. do I need to use two ic 74ls151?

[@Raghavendraraop]

74151 is a 8 to 1 multiplexer. Yes u need two ICs.. this is because 74151 has only 8 inputs whereas you have 16 input combinations. Short the corresponding select lines of both ICs to give 3 select lines. And the other one connect to enable pin and use it as another select line. So totally u need two 74151, one inverter gate and a OR gate

[@zackhaziq1116]

@@Raghavendraraop ouhh thank you very much sir

[@curlyterise8469]

Hello. I need help with my simulation. We were given an SOP equation and were told to simulate the multiplexer based from the given SOP. Can you help us please

[@Raghavendraraop]

Ya.. can u tell the equation

[@curlyterise8469]

@@Raghavendraraop thank you so much!! Implement the Boolean function F (A, B, C, D) = ∑m (0,3,5,6,8,9,10,12,14,15) with a multiplexer circuit using 74153 IC.

[@curlyterise8469]

@@Raghavendraraop And also this, simulate 5-to-32 line decoder circuit with four 3-to-8 decoders with enable and a 2-to-4 line decoder. There are a lot of videos about how to create block digrams about this but no simulation videos and we don't know where to start

[@Raghavendraraop]

@@curlyterise8469 Whether the function has to be implemented only using 74153 or can logic gates be used along with 74153

[@curlyterise8469]

Raghavendra rao p i think logic gates can be used just as long as we use the ic. I don’t know how to implement the equation 😅

[@masternoobway3564]

Do you have 16 to 1 multiplexer example?

[@Raghavendraraop]

No.. but you can construct using two 8.1 multiplexer