Music Reactive Led Strip | How to make music reactive 12v led strip using one MOSFET

Buy Electronic Component From Here:- www.electronic...
* Mic www.electronic...
*220k resistor: www.electronic...
* 12v LED strip: www.electronic...
* IRF 840 MOSFET: www.electronic...
*12V 1.5AMP ADAPTAR www.electronic...
Please Check our new channel & give the review and suggestions
/ @electronicspices01
In this video, I am going to make MUsic Reactive Led strip using one MOSFET IRF840
If u really like this video then #LIKE #SUBSCRIBE # SHARE
If you have any questions ask us in the comment
Like us on Facebook / jhaelectronic
Track: Mountkid - Dino [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Mountkid - Dino | Trap...
Free Download / Stream: ncs.io/dinoYO

[@memes7705]

TQ BHAI MAINE BHI AISA SYSTEM BANAKAR USKO LED STRIP SE JOD DIYA VERY COOL, PAHLE MAINE AISA SocHA thn search karke aapke video se poora kiya. Tq again

[@fhuber7507]

looking to do similar with RGB strip, but I want it to cycle colors sort of randomly, not timed to music. ****************** 12V RGB strip (common ground) Vary the voltage to each line, but at different rates. Such as: Red cycles over 4 sec, Blue cycles over 5 sec and Green cycles over 6 sec. (from 0 to 12V to 0)

[@javilarg]

Nice project man. With two more strips (red and green), two more mosfets an a few more parts (capacitors) you can make a 3-channel lamp, one colour per frecuency: high, mid and bass.

[@RJImagination]

+Javier Garcia Alvarez interesting!

[@andymakethetea]

RJ Imagination Please try this out!!

[@haroldriascos3876]

Javier Garcia Alvarez how I do this, I want do this

[@niru215]

I have 12 volts rgb leds i want to see XD

[@peterinbrat]

Javier Garcia Alvarez That's exactly what I want to do...

[@imugilee1137]

There is a miss. LED strip negative on Source pin of MOSFET must change to LED strip negative on Drain pin of MOSFET. The video is correct but subtitle has miss typing ( 1:26)

[@leynmp4]

*Пойду сделаю такую же штуку. Я бы до такого не додумался, а ведь это просто и гениально!!!*

[@angusdempster2038]

Try using a variable resistor to change the input amount so you can use at all volumes

[@dakusukhdevsingh]

MOSFET - IRF640 KA HAI BHAI or kya kya chaeye plz ache se full form me btana bhai i like u r product

[@aikincaya8491]

can i use mic from broken headphone ?

[@kamtagupta7608]

Nice project all thing is working but blinking is not so much good

[@yadavgopal2854]

Mic can be found on which simulation software

[@RyuWingsProduction]

Awsome tut but could you tell me the configuration for 5v led strips?

[@peterinbrat]

Can you make it so one strip reacts to base, another to mid range and a third to high range?

[@RJImagination]

+peterinbrat okay

[@KuldeepSingh-zt4cg]

Mic ki jagah aux cable laga sakte hain?? Same process me?

[@innovativetechs9646]

Kuldeep Singh aap is video ko try Kar sakthe ho Bhai _ kzbin.info/www/bejne/gpS3op2grMl-pZI

[@electric_mix]

Very nice

[@azaruddinazar5453]

Thanks for explaining it clearly.please help me .... what are the components need to drive 18watt submersible pump on music please reply or make a video.....

[@EduardoRodriguez-nw5hx]

Walmart has some for 5 bucks and with a remote control. I think its like 60 inch strip and can be connected via usb

[@Eliosama]

Greetings and good video, I am using a translator and I hope I can understand what I want to ask ... It is possible that once a microphone is attached to the connection, it is possible to place a 3.5 female jack so that the audio enters from a speaker, through a male cable extension at each end. If this was the case, it is possible that it recognizes the highs and lows of volume or frequency, so that different colors of LEDs light up, or it would be a different connection for highs and lows ... Thank you very much, I hope it was understood, and grateful for the video :)

[@sahilchaudhary953]

Bhai plz tell how to check +ve and -ve of electric mic? One which I have does not indicte anything. Also how to chack gate pin and source pin of MOSFET? My project is not working. Plz help

[@RJImagination]

+Sahil Chaudhary connect to me on Facebook and send some pictures of your project

[@abstestcentre6232]

AS PER YOUR DIAGRAM DOES THE LED STRIP NEGATIVE GO TO THE DRAIN PI OR SOURCE PIN OF THE MOSFET ?

[@Gamer-md3wm]

Can u pls make a video about how to switchover the same project with mic and direct supply(means i want this led working with and without the mic)

[@ceylontamiltechnician6750]

நல்ல முயற்ச்சி வாழ்த்துகள்

[@vinothkannachandrasekar3921]

Any alternative for 12v LED strip driver???

[@bornforgaming6079]

Very very nice video👌👌👌

[@gokulmrvkm]

Thanks for making this cool project. I just finished making this. The issue I'm facing is; it does not react to the music played through my phone; even at max volume. And I figured that when I blow air to the mic, the strip lights up. So I placed the mic on my sub woofer's air outlet and its working fine with the bass. I'd like to know if there is any way to improve the mic sensitivity so that the circuit will react to sounds coming from a distance? Thanks in advance and all the best.

[@sharifludin3008]

nice job, let me ask one thing, can we use a 12v DC motor Instead of LED lights?

[@kasunbro5576]

Is this right thing??? >>> IRF840 IRF 840 Power MOSFET N-channel 8A 500V TO-220 IR

[@herysuprapto9003]

if not use electric mic but change with cable and connect or plug in to output speker activ it will work or not? thanks and sorry bad english :)

[@nkelectricals2336]

Good job RJ muje yhi cheej chahiye thi Thanku bhai

[@RJImagination]

+Nk Electricals WELCOME

[@gatunoooo]

Good Morning. I'm trying to make the same video but it's not working. I was thinking the Mosfet you used is "P" or "N"? Another question is whether I can use a microphone from an earphone? Thank you, congratulations for the videos.

[@treasureshub2994]

Hello RJ i made the same circuit. But there is an issue when i connect to power lights turn up. MiC isn't working. Why? Can you plz help me.

[@RijuChatterjee]

Damn good man, simple and effective. I did something like this but never thought to use FETs. Obvious choice though. Keep it up.

[@mayurtajlove]

Bhai ckt diagram to milgayi mujhe.but I have one question aapne small led strip use ki he., Or mere pass badi wali led strip then this will work on this strip.

[@hoodratstickfight292]

So does the gate effect, or on off of the light, just happen at a different sound level with different gate mosfets?

[@inspiringbone4365]

Background music..is lit can uh plzz tell me..?

[@shortsirkit8270]

Awesome bro your name is Rj and my name is Rj I like it

[@dailybot8227]

заебок. разберу старую колонку, вытащу мосфет похожий, резистор только хз где взять, а микрофон из наушников, вместо ленты у меня есть 5 вольтовая гирлянда, запитаю от обычного адаптера телефона и готово)

[@josedako5728]

Hey, this is amazing, only a question, this works without Led Strip Driver? Or this component its nessesary?

[@RJImagination]

+Jose Dako all components are necessary

[@cocolocco7078]

Great job.can you please tell me if I can make the led band located on the kick drum to light when kicked? Thank you!

[@kapkap29]

I have a question, if I have a rgb led, what change a need do at the circuit?

[@RJImagination]

+Kevin Antonio Alcantar Peña use MOSFET on ground pin of strip

[@R_motomech]

hi i liked ur video but can u tell me that can we change a ac motor to dc motor. or can u make a video on it plzz

[@ihsanmurat7332]

is it possible to adjust a pc chassis fan with this, if i use a potentiometer, instead of mic?

[@RJImagination]

+ihsan murat check this 👇 kzbin.info/www/bejne/oYLaqmljadyJhNk

[@memes7705]

N bros! It works just need full bass sound. If u really want to made than I'll suggest u bcz I've made that responds accurately

[@rommelbien9413]

sir can u give me idea what electronic device i can savage transistor so that i can try to make this.i am working at sea thanks

[@RJImagination]

+Rommel Bien inverter

[@chrisg6635]

Can you do this with a strip from amazon that has a color changing remote? Add a switch with the mofset so you can have it either on or off without loosing remote functionality?

[@kaushalkhandelwal6189]

In your case when there is no sound signal LED is on but in my case its not turned on when it gets sound signal it gets turned on. Why?

[@mrdotak6]

Can we directly buy it as a direct product from local electric shop instead of manual job ?

[@ravilpatel8629]

RJ can you do a video of led reacting to thunder sound with only blue or white color mode?

[@TheMuhh123]

Can you also ist RGB led's ? Or only one coloured ones ?

[@RJImagination]

+TheCarn okay

[@lshomedesign]

Very nice idea....I will also try to this.

[@soundwaveproductionsph1925]

can i ask if possible to use 3.5mm jack instead of mic as a source of music ?

[@RJImagination]

Yes you can use

[@hunnyrockz9555]

Kia yay ek waqt may ek h 5metr led strip py chaly gy? Ya zada py b yay ek kam chalga?

[@g.k.cinemahouse9613]

Bhai ye Jo black colour Main Choti Si he Woh Kya Hai or vo mujhe kaha milegi please brother reply me

[@diahhrg4667]

Am want talk. Mic for a handphone or mic condensor? Please answear

[@knockoff79]

condenser mic

[@Supportta]

Can we give it direct audio output instead of set it up with a mic?

[@rahulv7791]

Can i use 3.5mm jack instead of mic,so that i can connect it in my phone/laptop,without changing any other components..?

[@abdulqadir-vd3yg]

12V DC adapter will work? Having 600mAmp

[@RJImagination]

+abdul qadir yes

[@josheploa9578]

can a jack be used to replace the microphone?

[@andreborda7355]

instead of a mic could I put an aux cable??

[@raymundomendoza4562]

Amigo chidos tus videos una pregunta k otra tecistensia puedo usar sino tengo una de 220k y donde saco el microfono

[@nyorkennethsandot2068]

can i use IRFZ44N IRFZ44 Transistor MOSFET ?

[@CbaezP]

Supongo funciona igual si en lugar del microfono se solda una entrada plug 3.5

[@vishnumohan556]

I made this but its not works with sound. When switch on the light on normally... what is the mistake

[@MysterP]

Can a piezo replace mic for a pressure sensitive strip?

[@RJImagination]

+Bobby Hancock yes

[@theajay7843]

wow nanja Aa Gaya sir

[@SciNix]

Someone Help me i did the same thing with IRF740a of dame 30v VGSth but when I check it with multimeter (Still didnt connect Light wires) it shows 12v Everywhere even when nothing playing on microphone . Btw you say led -ve pin to Source and connect it to drain (Any difference?) Please HElp Thanks Edit:I connected the light wires and tested it lights up faintly thats it id dosent even change a little bit depending on the music Please help is mu mosfet Broken i have another one

[@mijeetv8618]

No work!!!! Help me. IRF840, 220k, Electric MIC, Led strip, +12V DC ~~IRF840 Gate pin + 220k + mic positive + LED strip Positive + VCC. ~~IRF840 Source + Mic negative + GND. ~~IRF840 Drain + Led negative. This scheme yes or no ???

[@RJImagination]

+Mijee ee diagram is available in community tab of channel ! Or for any help connect to me on Facebook link in a description of the video

[@ziahaxhmi3039]

Sir ek or help krden, ye mosfet kisi or circuit mai hota hai to bata den hamare city mai ni mil raha

[@jnielson09]

Lo qie puedo notar es que solo funciona con el sonido ambiente. Si en caso tal lo intalo en mi auto. Y quiero dejarlos ensendido de noche solo encenderan si hay ruido Pero aun asi es bueno el video...

[@patmccrotch7811]

Can the IRF 820 be used if I don't have the 840

[@francisrogerrodriguez2631]

can i use / connect audio jack output instead of the condenser mic?

[@manojvarshney7450]

Bro can I use 2n222 resistor instance of MOSFET..? Plz tell me fast

[@RJImagination]

+Manoj Varshney check this👇 kzbin.info/www/bejne/sJyUiWRnbcSHfdk

[@ekdantofficial9422]

Bhai. Itna Bata do ki ending me song kaunsa Tha please reply OK

[@RJImagination]

+Baria Hitesh link in a description

[@kamtagupta7608]

Can i use anoter mosfet,because in shop i didnt get this. Other mosfrt is avaible

[@kamtagupta7608]

Plzz tell

[@RavindraKumar-ru5eo]

Please make a video with c8550 or c8050

[@RJImagination]

+Ravindra Kumar no!

[@preetam.singh7]

Bhai ye speaker mobile s kase connect hoga... By the way superb job...

[@yasir2ayan]

Mobile me connect thodi kia hai bro

[@deiviskat]

Can you expand it to three channels? Show it in a video or send a diagram on how to do bass, mids and highs?

[@RJImagination]

+Leg-IT Studios okay

[@manoharkumarmahto]

working for me but only on very high volume and when i keep the mic very close to speaker. Is there any way by which I can make it work on low volume.

[@adityakadali]

Use an amplifier circuit

[@manoharkumarmahto]

@@adityakadali Pls share circuit diagram

[@ayubsayed4346]

What is the music name

[@ayubsayed4346]

Ncs music

[@shushantkumar346]

I also make this but not working , can there are any method to check MOSFET is correct or not ?

[@naveedkamboh125]

Resistance voltage kea hay Mike - + kon SE hay agli video mean lekhay

[@niranjanmaske2819]

Resistance ka golden colour kiske tarf hona chahiye mosfet ki tarf ya led + ki tarf

[@RJImagination]

Kisi v side ho koi fark nhi pdta resistance me polarity nhi hote

[@pratipsarkar7460]

Jadhar marji ...koi farak nehi parta

[@rajendrakumhar7925]

Kya MOSFET irf840 ki jagha koye or mosfet use kar sakte h kya

[@moindiwan5393]

Which song do you used in this video...plss give ans??

[@farhanqureshi14]

Bro can we attach aux cable instead of mic plzzz reply

[@simonkenaguirre]

it would be great

[@nitro1705]

will it work with a 9v battery in any way? thanks ;-;

[@shotoniphone1841]

This is too easier than i think.damn it😅. Yeah great. I made it too. Work very well with my subwoofer 🔊

[@abdulwahab1995able]

Please help me in this circuit. Strip light was continously standing in on position. Help me how it will blink with music.

[@josesalcedo296]

Hello Can i use mosfet IRF460 ? Thanks from Argentina

[@hitman2763]

I'm using 6N60A mosfet dose it work??? Please tell me bro

[@hritikraj797]

How can I make this function in series lights of AC current

[@RJImagination]

+Hritik raj okay

[@mohsinjokhio8047]

I have IRF840 and 120K resistor will it work?

[@janloiearaque9461]

Where can i find this simillar mosfet in old components?

[@satyamshivam6720]

Hey when i complete the circuit and switch on then the led strips glows normally without any sound or flashing please help

[@RJImagination]

+Satyam Shivam connect to me on Facebook link in a description of the video and send some pictures of your project

[@apnafugana2151]

Bhai mosefat dusri bhi chal jayegi kya please tell me bro

[@niru215]

I can use a different type of resistance?

[@evilplay22]

I love you bro you solve my problem

[@user-lz5ew1hy5f]

Sorry for asking..to make that thing,can i use NEC D882?

[@RJImagination]

+syaz 99 no!

[@anmolkumar6704]

@@RJImagination can i use z44

[@PawanKumar-it7le]

Bro RJ jo black ic hai iska number kya hai or 220k ka colour konsa hai

[@mohammedmushtaq7986]

Nice yaaaar.....kiya kiya zurat hai wo ....discription me likh na to sahi

[@fayascb7239]

bro can i use 6v battery and led ,and you guided on that video to connect led stripe positive to G terminal and negative to S terminal. but you were connected negative to middle D terminal. why?

[@RJImagination]

+FaYaS cB actually that was a editing mistake diagram is available on my channel community tab

[@RJImagination]

+FaYaS cB yes you can use this circuit with 6v