My Agile HF DX Antenna - Compact 6-Band 20-6m Antenna

Here is an interesting 6-Band 20m-6m antenna that takes up little space, and is easy to make. Ideal for portable or home use.
LDG AT100 Antenna Matcher.
www.hamradiostore.co.uk/produ...
Xiedgu X-6100 Transceiver
www.hamradiostore.co.uk/produ...
4:1 Balun
www.hamradiostore.co.uk/produ...
Spider Pole
www.hamradiostore.co.uk/?s=Sp...

[@WECB640]

Thanks Peter for discussing the virtues of the doublet and balanced line. The new hams need to hear this as it's often buried. 73.

[@acestudioscouk-Ace-G0ACE]

Thanks Peter, you made some interesting and new to me points about the old stalwart, doublet. Fashions come and go but there is a lot to be said for this simple and efficient antenna. Best 73.

[@traveleractual]

Thanks for this, I'll have a go at this for my next antenna project.

[@davidportch8837]

as always... great practical advice Peter... many thanks...

[@darylnd]

Thank you, Peter! I always learn from your videos. I'm strictly portable/QRP operations. My QTH, both by design of the building (5-story condominium apartments, U-shaped building, my unit is 2nd floor on the inner courtyard) and its location in the city (blanketed by surrounding structures and power lines: I have to walk up the block to make a cell call some days) is pretty well impossible for radio. I normally operate from a few parks at the southern end of the San Francisco Bay--a few minutes drive from home and nice ground plane on the salt marshes--but only one has room to deploy my 10m - 40m EFHW. I've been looking for a smaller footprint, multiband antenna. I'd been thinking of adding a matching unit to my IC-705 kit: this convinced me to go ahead with the compact, manual ZM-2 tuner from Emtech. As an aside, I've finally begun learning CW. My key is a WT 8 AMP. 73 de KN6NPZ, Daryl, San Jose, California

[@christopheriles1469]

Thank you Peter, another very interesting video 🙂

[@nr3rful]

Always interesting.....great knowledge 😅

[@kevinverville8608]

For lightweight, and portable doublet operation, I prefer 350ohm line. It is lighter, and easier to work with than the 450ohm line. 73 de KC1DBR

[@davem0udb]

Another interesting video. Would it matter if the length of coax was longer, say 15m

[@DonzLockz]

I've always like the idea of a doublet and the X6100. :)

[@sophoklesgreek3237]

thx Peter, interessting as always. there is a particular idea for an antenna that I would like you to cover in one of your videos. You heard about quax antennas ( or coil antenna)? it is basiclly a pvc tube and you wind up a full lambda wire on it. e.g. 60m of wire with a copper rod at the top for tuning ( you cut it down) on feed point you put some radials.. . It is not good for the ground wave.. but theoretically it works good for anything else . I know that sounds like a giant dummy load ..But I read some stuff about it.. and it seems to be legit .. anyway.. I really like to hear your opinion about this. '73

[@wigjohn]

What balun would you recommend that would work from 20 metres to 6 metres with this antenna? As usual another great video, thanks. As a ‘B’ licensed amateur for nearly 50 years operating 2 metres and above with a recent switch to HF the choice of antennas for my small garden becomes critical. :)

[@Siskiyous6]

A 4:1 is the usual choice with doublets, if your ATM is designed to take the wires from twin feed directly it likely has a 4:1 built in. I tried many ways to feed my doublet when I first put it up, and an ATU designed for receiving the twin lads directly is far and away the best solution.

[@Sidmi5utc]

Watch the video again, your answer is waiting...

[@ehayes5217]

Excellent explanations! 73 de WA4ELW in TN 🇺🇸 dit dit 😃

[@watersstanton]

Many thanks.