My hm minitractor -tyrants

[@alexandrutyukodi6713]

Felicitari o lucrare frumoasa merita.

[@dougrector4412]

Good looking job...but your 3 point hitch arms do not spread out or in ,how will hook up to different attachments?

[@pitibadea8762]

All attachments are adjusted to match with 3 points. Use accessories made by me.

[@ovidiete8548]

f frumoasa lucrarea dumneavoastra! da sincer cred ca merita un motor putin mai mare.si tirantii puteati sa le faceti sa se poata lati si angusta.totusi e parerea mea felicitari pt lucrare!

[@lagojal]

Esta muy padre tu tractor. Este tractor aclaro algunas de mis dudas en cuanto a la construccion de uno propio.

[@miltonalvesdasilva7983]

Show de bola maravilha de brinquedo

[@Артем-щ6ю3ю]

Не только на Руси умельцы есть! Красавчик

[@pitibadea8762]

Важно любить то, что ты делаешь

[@garciaribeiro7120]

o melhores videos que vi ate hoje parabens amigo

[@pitibadea8762]

obrigado

[@garciaribeiro7120]

Ok Piti obrigado por ter respondido tenho 60 anos sera que consigo fazer um para mim.

[@pitibadea8762]

Tenho 67 anos e eu gostaria de construir

[@garciaribeiro7120]

VOU TENTAR ME ESPELHAR EM VOCE ,ESTOU EM SP BRASIL mora onde mestre Piti

[@jamesrdugger1701]

pin on cylinder to threepoint looks to be in way of tread shorter pin needed perhaps?

[@arrzzh]

ما شاء الله الله يقويك ممتاز

[@garciaribeiro7120]

os dois sao muito bom o da retroesquavadeira e este,

[@pitibadea8762]

avaliações respeito

[@mechanicaltechnical498]

Can i get its drawing sir?

[@moisesmachado6698]

Atrás n precisavá de mancais. Essa peça na requer movimento constante

[@robertdonald4409]

nice ! i think ur arms need to come up more ! and not so much down

[@pitibadea8762]

There are no problems

[@erwinschadt6978]

Eu vreau un tractoras pt cosit si un excavator eventual si un plug ma gandesc la un motor de dacie ma poti ajuta? Vei fi invitatul meu gratis la mare

[@slvp4691]

Frumos,dar vream mai multe detalii ,nu numai hidraulica

[@pitibadea8762]

Detaliile sunt in filmuletele postate de la inceputul proiectului. kzbin.info/door/Jby6XtxBEIzQLZT-fpeMhA

[@terapiu]

Foarte bine lucrat, felicitari! Am o intrebare...pompa hidraulica de la ce este?

[@pitibadea8762]

Multumesc de apreciere. Pompa este facuta la Plopeni, si se gaseste in toate magazinele care vand piese pentru tractoare. Am dat pe ea 200 roni la un magazin care vinde piese auto si utilaje agrigole.

[@johnpalma7265]

Qual é a sua cidadania,qual bandeira juras Allianza?

[@petermenashpetermensah1842]

Is this just to show people how the hydraulic works?

[@erwinschadt6978]

De unde esti???

[@vikashpanday9238]

batao Bhai thora

[@kamilchamik6560]

Szkoda kasy i czasu jak silnik stęka przy pustym podnośniku

[@erwinschadt6978]

Ai tel whats app ??

[@7891ph]

While you seem to have and understand the nessesity of knowing how to weld (KZbin has lots and lots of channels that show you how NOT to do it), your geometry for your rear hitch and front end loader are definitely not ideal. The rear hitch is built very stout, except for the fact that your pivot bearings have only 2 small bolt's each holding the bearing cap's on in the direction of maximum load if you intended to go plowing. Those 4 small bolt's are now the fuze in the system. As for the loader, the pivot points from the top of the loader uprights to the fixed points for the cylinders is way too close together. You're throwing away a lot of your mechanical leverage, while adding a lot of extra stress to the fixed uprights, due to the hydraulics fighting it out with the poor geometry in such a small area. The same can be said about where the lift cylinders attach to the outboard end of the lift arms. You have them mounted inboard of the welded joint where the upper section of the loader arm's, rather than the drop section. Move the brackets and you will put much less strain on that joint. And if done correctly you will loose at most 25~30mm of lift height. I know it's late in the day, but I just had to throw that out there. I'm hoping that even with my critique, you've had nothing but safe operation of your tractor...

[@vikashpanday9238]

open videos

[@oskar7304]

to Small engine

[@pitibadea8762]

True, but it changes easily with another bigger engine

[@jamesdodd7404]

BORRRRRRRRRRRRRRRRRRING