My Laser Is Cutting Bad

[@sanjuchauhan3072]

You didn't say what changes you made to the parameters. Please explain this

[@qchitanie]

Easy to solve, use less gas and speed. Will help allot... And maybe play little bit with the focus.. 399usd Pfff hard for some settings

[@joelamoos5684]

How did you learn parameter setting?

[@sivaamulu9128]

Sir. Can I increase the cut focus value or decrease the cut focus value to remove the notches

[@mhxxd4]

Or just more power

[@4tra]

Center of lens is not in limits. Try regulating lens. other thing can be that the last glass is dirty, need to change < experience with HSG industrial lasers over 4 years

[@bcbloc02]

Tuning makes a difference!

[@WokeCancer]

Looks like too much power or running too slow. Assuming you have a good lens

[@naengineer]

keep lenses, clean this is crucial, keep laser beam in center with transparent tape, have a very clean oxygen, good pressure regulator and than you can proceed tinkering with the parameters

[@bradsmith1896]

Having this problem now. 3/8” carbon steel. Running oxygen. Man I’ve messed with all the settings. Also using cypcut

[@turbocobra]

yea, most guys do struggle with that, but its easy to make them cut like butter if you know the process.

[@bradsmith1896]

@@turbocobra and 3/8" is its max. I'm sure that has a lot to do with it. It's at max power

[@joelamoos5684]

​@@bradsmith1896how many KW is your laser source?

[@bradsmith1896]

@@joelamoos5684 2000 KW

[@nirajshukla3462]

I opted 3kw I have issues for understanding parameters for parameters

[@adityarajsinhvaghela5335]

Is the issue still there ? I can help.

[@billlangdon9198]

Still pretty impressive for that thick of material. Nice work Gary. Wishing you the best in the New Year.

[@GREENEYEDBANDIT313]

Hey what's going. On. I'm cutting some 3/4 on a 6kw fiber laser cutter. What parameters did you adjust. To get that smoothness ??

[@turbocobra]

you have to buy the videos for it man, I have tons of videos showing all kinds of things for free, but if you want to learn how to master your laser, you have to buy the course.

[@Notreallyhere817r]

Reduce the gas

[@manjooraliansari2742]

How to buy your course

[@NickCicala-mu9yx]

Biggest adjustment is gas pressure, then speed, and power. 02 cutting is lower pressure, and .1 bar can make quite the difference. .5 to 1.2 bar is depending on nozzle and cutting head. Carbon steel cutting shouldn't use more than 6k, Unlike nitrogen cutting where the more power you have the faster it can cut.

[@joelamoos5684]

Hi Ramsay, are you an agent for Oree?

[@turbocobra]

No

[@GamezJP]

Hi Ramsey, I'm so thankful to have found your channel and now find out you sell training for these chinese lasers. I'm about to order my first chinese fiber laser, 6kw enclosed, at this point I'm just zeroing in on two resellers, I would like to be able to buy from you, but I'm not in the USA they both offer this optional software Cypnest instead of Cypcut for $1,480.00 USD. From what I've found, everyone says it's better to get this Cypnest option if you can. But I haven't found out if there is a better option to both of them. Do you have any experience with Cypnest? Do you recommend it or something else? and, Will your Cypcut training package help me setup my machine if I end up getting this Cypnest software?

[@joelamoos5684]

Did you end up buying your machine already? I have experience with CypNest

[@GamezJP]

@@joelamoos5684 yes, it took long, but I should have it in my shop November 7. For all I was able to find online, it did look like a good choice to order cypnest with my machine, have you found cypnest better than cypcut?

[@gustavoanuch890]

Same question, what did you do?

[@GamezJP]

@@gustavoanuch890 i ended up getting it, I’ve had it up and running for a couple weeks now, I guess I was more apprehensive about this than needed. Setup was easy. Sometimes I get stuck tuning some materials, but otherwise once I get to where my machine’s parameters work… it’s a dream come true.

[@Oliveirlacerda3426]

I work on a 3000w gweike fiber laser machine. One of the problems I have is with heating the plates in small areas.

[@joelamoos5684]

How had your experience with Gweike been so far?

[@Oliveirlacerda3426]

@@joelamoos5684 It's an excellent laser cutting machine, but it's lacking in some cyp cut functions.

[@gustavoanuch890]

I am buying a gweike also, hows the experience?

[@Oliveirlacerda3426]

@@gustavoanuch890 for cost benefit, a great machine, very low maintenance and simple operating system

[@parist5490]

I work on a gweike 12kw. Guys there is so much smoke coming out of the fully closed machine that you couldn't believe. Especially when cutting with oxygen. Also table change is very slow around 45sec. As far the parameters concerned, there aren't any. Be prepared to buy at least 20 protective lenses because that son of a bitch gets dirty really easily

[@DEARRAEDDEAR]

So what caused it to do that?

[@turbocobra]

its the nature of oxygen cutting at the max of a power level on a laser, its finicky, difficulty, constantly changing

[@parthipan5103]

Slat not propper cutting

[@rabresham3387]

Hi

[@gorkemsariova1509]

merhaba kesim güzel olmuş faka çok az oksijen gazını azaltmaısın lazer filizlerini daha yok edebilirsin diye düşünüyorum

[@ahmetkayur]

O2 gas too high.

[@torukos]

Exactly 👍

[@dursunkrman5363]

Ahmet bey iyi günler Bu konularda bilgili birisine benziyorsunuz Bana da yardımcı olur musunuz

[@Feramist-h2t]

​@@dursunkrman5363ben olabilirim buyrun sorun nedir

[@emilyqincncroutermachinean471]

Cool !!

[@AsadUllah-km9xo]

Hi bro any one need laser designer. I have 8 year experience

[@sarathkumara2254]

🙏

[@oleg4e369]

lol. 400$ )))

[@turbocobra]

Its now $500 and should be more!

[@Feramist-h2t]

​@@turbocobrasen bana ver 300 dolar ben yardım edeyim sana kamil O2 ve gücü vermiş yarık yarık kesmiş sonra 2 ni azaltmış 500.dolar.istiyor:)