My NEW FC Stacks Have Arrived! | SpeedyBee F7 V3 50A & F7 Mini 35A Flight Controller & ESC Overview

Unboxing and overview of the new feature packed stacks I will be using in my next 3 inch freestyle and 5 inch freestyle builds.
=========================
Items suggested in this video
=========================
SpeedyBee F7 V3 BL32 50A 30x30 Stack:
Direct: www.speedybee....
GetFPV: bit.ly/3wzmu0p
SpeedyBee F7 Mini 35A 3-6S 8-bit Flight Controller Stack:
Direct: www.speedybee....
GetFPV: bit.ly/3kIHP50
My Favorite Screwdrivers (Wiha Slotted & Phillips):
Amazon US: amzn.to/3tq15Eu
Amazon Canada: amzn.to/3E1Ph02
DJI FPV Goggle V2:
Amazon US: amzn.to/3H9FGZk
Amazon Canada: amzn.to/3VLHQlY
DJI O3 Air Unit:
Amazon US: amzn.to/3WZnupK
Amazon Canada: amzn.to/3jJszUR
GetFPV: bit.ly/3ioEE1s
DJI FPV Remote Controller 2:
Amazon US: amzn.to/3EPa8oJ
Amazon Canada: amzn.to/3XJRZ4w
XING2 1404 4600kv Motors:
AliExpress: s.click.aliexp...
Banggood: www.banggood.c...
GetFPV: bit.ly/3GQa7mz
Happymodel EP1 Receiver:
AliExpress: s.click.aliexp...
GetFPV: bit.ly/3GRtYC8
TBS Crossfire Nano Receiver with Immortal T Antenna
GetFPV: bit.ly/3Zm2WK6
TBS Tango 2 Pro
GetFPV: bit.ly/3QsPlgj
============================
Links
============================
SpeedyBee F7 V3 BL32 50A 30x30 Stack Manual:
store-fhxxhuiq...
SpeedyBee F7 Mini 35A 3-6S 8-bit Flight Controller Stack Manual:
store-fhxxhuiq...
BlueJay BLHeli_S Firmware GitHub:
github.com/mat...
#speedybee #fpv #drones
Mandatory Disclaimer: I participant in the Amazon Services LLC Associates Program, which is an affiliate advertising program designed to provide a means to earn fees by linking to Amazon.com and affiliated sites. Item suggestion links above are affiliate links and I will receive compensation if you choose to use them. There is no cost to you to use these links and any compensation received goes right back into the channel.

[@macksenduro9796]

The cable that comes with purchase of O3 Air Unit plugs directly into the SpeedyBee F7 V3 which I thought was awesome, I'm using their stack on my first quad

[@Mangorille]

You are correct! Still would have loved a cable to be included, all manufacturers used to include the DJI connector when the original air unit released.

[@luvmyhondasi]

The speedybee stuff blows iflight out of the water.

[@Mangorille]

Ya so far really good experience. Only problem is that the F7 V3 stack is really tall and I am having an issue installing it in my latest build which has a low profile frame.

[@TinChozZz]

Vamos Mango! Desperate Suscriber here! Thanks for all this excellent material.

[@MadDragon75]

I love mine. I just switched from 1507 motors to 2205 motors on this ESC. So far no issues. 👍

[@Mangorille]

Thanks for the comment. Is this on the Mini or Full size stack?

[@MadDragon75]

@@Mangorille the 20x20 stack.

[@Mangorille]

@@MadDragon75 Nice, those are fairly large motors for a 20x20 but then again they did test that stack at full output for 30 seconds.

[@MadDragon75]

@@Mangorille well, my first flight pulled 61amps I believe, in around 3 minutes on 4S. I didn't notice any excess heat.

[@Mangorille]

@@MadDragon75 Awesome!

[@RC-Flight]

I have both of these stacks, the new version 50 amp for five inch and the smaller FC for a 4 inch build coming up. So the mini stack, already comes with the blue jay already on it?

[@FourthWayRanch]

the motor pads are close to the FET on the mini

[@Mangorille]

Ya they are, you need to make sure the soldering iron doesn't slip.

[@AsgardStudios]

I’m digging my F7 V3

[@kkeil9449]

This would be my favorite FC if i can figure out the correct resource & PINIO info for DJI aux switch.

[@Mangorille]

I haven't done this before but JB has some videos on PINIO and switching things on/off with it. Maybe start there?

[@budnanc509]

I am having an issue with my speedybee f7 stack, Can't get inputs in betaflight, using elrs rx and tx16s tx. uarts are right, rx/tx are switched, any many variations of all the above. Did you have any issues or have suggestions, I changed rx's no change, changed new f7v3, no change. Thanks

[@Mangorille]

When you run the LUA script for ExpessLRS, does it say Model Mismatch at the top where you have the number of packets?

[@RC-Flight]

What’s up with the financial advice LOL you have been bombed 😮 20 comments not related to your video at all!

[@Mangorille]

Yup, so obvious too.

[@bennguyen1313]

Just curious, are the schematics and firmware available for just the SpeedyBee F7 V3's top/logic board (the one with the STM32F7422, not the BL32 50A 4-in-1 Electronic-Speed-Control or 45A BLHELI32 board)? I like that it has Barometer BMP280 , IMU/Gyro BMI270 and ESP32-S3 (bluetooth/wifi).. so just want to purchase the top alone (not the Voltage Regulators / Battery Elimination Circuit board) to play as a development board with my own sensors (ex. Beitian BN-880) However, I'm concerned that I won't be able to flash/debug using SWD.. or if it's somehow locked to be used only with the Betaflight 3.5.2 / Emuflight / iNav firmware / app? BTW, is there a parts list of drones/motors/GPS/etc that is sure to work when plugging the F7 V3 as a stack?

[@Mangorille]

You can buy the flight controller separately but if I understand the kind of schematic you are looking for, I haven't see anything like that. You'd probably want to reach out to SpeedyBee directly and see if they can point you in the right direction. I'm working on a build with this stack and I'll have the parts list in the video description once uploaded.

[@jessefoote4794]

the v2 version is absolute absolute garbage. The uarts fail randomly on 3 boards i have used. I soldered correctly all of them because they did work for about three flight. I would change the uart to a different uart and it would work again for a bit then quit working slowly and randomly after about 3 flights. Absolute Garbage.

[@Mangorille]

That's annoying, thankfully I haven't had any problems at least yet on this stack.

[@Mahad458]

does this work with DJI 03 air unit?

[@Mangorille]

The full size one or the mini? And are you asking if it is plug and play (no soldering) with the o3 air unit?

[@moriwaky]

9:05 Hi just a quick question the power inducter I see on your speedibee 50 amp doesn´t look like other reviews I saw it online your`s like round or covered by somenthing did you had any problems with the esc?

[@Mangorille]

It looks like there is some protective glue/epoxy on there. No problems, I only recently got this and straight from SpeedyBee so it might be something that they've started adding to the latest ones coming off the line.