Рет қаралды 138
برای نصب گلس UV برای موبایل، مراحل زیر را دنبال کنید:
مواد و ابزارهای مورد نیاز:
1. گلس UV
2. چسب مایع UV
3. لامپ UV
4. دستمال
5. الکل ایزوپروپیل
6. نوار چسب
مراحل نصب:
00:05 تمیز کردن صفحه نمایش:
- صفحه نمایش موبایل را با دستمال میکروفیبر و الکل ایزوپروپیل کاملاً تمیز کنید تا هیچ گرد و غبار یا چربی روی آن نباشد.
01:00 چسباندن نوار چسب:
- نوار چسب را روی بخشهایی که نمیخواهید چسب UV به آنها برسد، مثل اسپیکر و دکمهها، بچسبانید.
02:00 حذف غبار با نوار چسب:
به وسیله نوار چسب غبارهای رو صفحه را حذف کنید.
02:30 ریختن چسب UV:
- چسب مایع UV را به صورت یکنواخت در وسط صفحه نمایش گوشی بریزید. سعی کنید مقدار مناسبی از چسب را بریزید تا تمامی سطح صفحه نمایش پوشانده شود.
03:00 گذاشتن گلس روی چسب:
- گلس UV را با دقت و به آرامی از یک سمت (بالا یا پایین) روی صفحه نمایش گوشی بگذارید. اجازه دهید چسب به طور یکنواخت زیر گلس پخش شود.
03:20 حذف حبابهای هوا:
- در صورتی که حبابهای هوا زیر گلس باقی ماندهاند، به آرامی با انگشت یا کارت پلاستیکی نرم حبابها را به سمت لبههای گلس هدایت کنید.
03:31 تاباندن نور UV:
- لامپ UV را روشن کرده و به مدت حدود 5 دقیقه (طبق دستورالعمل چسب UV) روی صفحه نمایش بگیرید تا چسب خشک و ثابت شود.
04:09 تمیز کردن نهایی:
- پس از خشک شدن چسب، نوار چسبها را بردارید و هر گونه چسب اضافی را با دستمال میکروفیبر و الکل ایزوپروپیل پاک کنید.
حالا گلس UV به درستی روی گوشی شما نصب شده و آماده استفاده است.
How to Install UV Glass Screen Protector for Mobile
Materials and Tools Needed:
1. UV glass screen protector
2. UV liquid adhesive
3. UV lamp
4. Microfiber cloth
5. Isopropyl alcohol
6. Adhesive tape
How to Install UV Glass Screen Protector for Mobile
Installation Steps:
00:05 Clean the Screen:
- Thoroughly clean the mobile screen with a microfiber cloth and isopropyl alcohol to remove any dust or grease.
01:00 Apply Adhesive Tape:
- Apply adhesive tape to areas where you don't want the UV adhesive to reach, such as the speaker and buttons.
02:00 Remove Dust with Adhesive Tape:
- Use adhesive tape to remove any dust particles from the screen.
02:30 Apply UV Adhesive:
- Evenly pour the UV liquid adhesive in the middle of the mobile screen. Use an appropriate amount of adhesive to cover the entire screen.
03:00 Place the Glass on the Adhesive:
- Carefully and slowly place the UV glass screen protector on the mobile screen from one side (top or bottom). Allow the adhesive to spread evenly under the glass.
03:21 Remove Air Bubbles:
- If there are any air bubbles under the glass, gently push them towards the edges with your finger or a soft plastic card.
03:31 Cure the Adhesive with UV Light:
- Turn on the UV lamp and hold it over the screen for about 5 minutes (according to the UV adhesive instructions) to cure and set the adhesive.
04:09 Final Cleaning
- After the adhesive has dried, remove the adhesive tape and clean any excess adhesive with a microfiber cloth and isopropyl alcohol.
Your UV glass screen protector is now correctly installed and ready for use.
#parsa.07 #trick #ترفند #craft #short #shortvideo #shortvideo #youtubeshorts #youtube #savemoney #خلاقیت #diy #diycrafts #diycraft #making #make #tricks #doityourself #clear #lifehacks #making #glass #UV_GLASS #uvglass