Neck pocket types, Break Angle, and routing the neck pocket.

  Рет қаралды 3,716

David Imrie

David Imrie

Күн бұрын

Пікірлер: 14
@ac7563
@ac7563 Жыл бұрын
Well done David. This gives me courage to attack this part of my PRS build
@rickmccl71
@rickmccl71 2 жыл бұрын
Most bar clamps let you reverse the jaws to use them as the spreader clamp you're talking about @14:00
@DavidImrie
@DavidImrie 2 жыл бұрын
Cheers buddy.
@Tribearaclops
@Tribearaclops Жыл бұрын
another option is to cut a block of scrap and use a wedge. i always make the wedge out of softwood so it doesn't leave marks.
@oneconsc3333
@oneconsc3333 3 жыл бұрын
Also, use on oversized neck template which extends over the edges of the body which you can keep flat, level to the back. Clamp everything in place and route the neck.
@dominickmendoza7813
@dominickmendoza7813 2 жыл бұрын
Though the neck is always the trickiest part of any build, it all looks great. We’ll done. As far as the clamps…Irwin and Jorgensen/Pony both make clamps where you can un-assemble the top piece and flip upside down so as to use the clamps as spreaders. I think that might work in future.
@DavidImrie
@DavidImrie 2 жыл бұрын
Thanks.. finishing is definitely the hardest part I'm my eyes 😅
@oneconsc3333
@oneconsc3333 3 жыл бұрын
Use the heel,of the neck, after positioning it properly on the body, to install the guide blocks around the neck heel itself for a perfect fit.🙏🏻💜🇨🇦
@tobaccorich
@tobaccorich 3 жыл бұрын
Did you finish it yet ? I m trying to do my first telecaster. You’re doing a good job.
@DavidImrie
@DavidImrie 3 жыл бұрын
Thanks buddy. I'm getting there. Just in the middle of sanding the body ready for finish at the moment.
@tobaccorich
@tobaccorich 3 жыл бұрын
@@DavidImrie Bravo Man. Good Luck.
@davidplatel3815
@davidplatel3815 3 жыл бұрын
Why didn't you just sand the neck pocket by another 0.3mm both sided for the second bit of veneer to allow you to use two veneers
@oneconsc3333
@oneconsc3333 3 жыл бұрын
But definitely route the neck pocket before shaping the body.
fretting a guitar for the first time
24:04
David Imrie
Рет қаралды 308
Planing the break angle in the guitar top
13:50
David Imrie
Рет қаралды 1 М.
Леон киллер и Оля Полякова 😹
00:42
Канал Смеха
Рет қаралды 4,7 МЛН
Гениальное изобретение из обычного стаканчика!
00:31
Лютая физика | Олимпиадная физика
Рет қаралды 4,8 МЛН
Routing Pickup Cavities.
22:06
David Imrie
Рет қаралды 2,5 М.
When the BEST Guitarists...aren't that great
9:50
samuraiguitarist
Рет қаралды 79 М.
How Much Money I Lost On Tour
14:20
Mary Spender
Рет қаралды 128 М.
Carving a guitar neck and volute with files
22:06
David Imrie
Рет қаралды 457
darkening a laurel guitar fretboard on an Epiphone Les Paul
27:14
Custom Telecaster - Episode 14 - Applying Finish
10:43
Voyeur Guitars
Рет қаралды 697
I can’t Make these Quick enough ! 32 products from a 2x4
17:15
BeardedVikingWoodWorks
Рет қаралды 34 М.
Guitar Shed Diary 49: Fretboard Inlay (Part 2) Epoxy?
27:41
David Imrie
Рет қаралды 3,4 М.