4 Days REAL use in on the inexpensive needle scaler and its showing NO signs of ANY problems or issues for usage. So for $40 how can you go wrong?
Пікірлер: 34
@voidisyinyangvoidisyinyang8852 жыл бұрын
I've nominated this vid for an Emmy due to the high class editing.
@rcguygarage2 жыл бұрын
😂🤣
@voidisyinyangvoidisyinyang8852 жыл бұрын
This vid made me feel better about just getting an electric scaler!! It really does remove rust very well - better than a wire brush. thanks
@vitix59064 жыл бұрын
Excellent visual representation! I think this along with a chipping hammer and a heavy wire brush grinder all working together will be my solution for my trucks frame resto... I was looking at that very same tool on amazon....SOLD!
@mongomay12 жыл бұрын
A air chisel helps break the heavy stuff, then needle scale.
@rcguygarage2 жыл бұрын
BFH works too😉👍
@Cjinglaterra4 жыл бұрын
We used these extensively in the Navy. I bought one from Harbor Freight to take care of some frame rust.
@rcguygarage4 жыл бұрын
They work as expected! Not the best but get the job DONE
@juliogonzo27184 жыл бұрын
Guy I worked for gave me one 6 years ago. Has sat unused since. Need to get scale off a scabby used engine I'm swapping in so I can paint it. Finally going to get used!
@tiredoldman53295 жыл бұрын
Nice vid. I just got the same one. haven't used it yet though.
@jeremylister892 жыл бұрын
🇬🇧 UK here! Are the needles specially hardened? Made of special steel or even something like tungsten? Tried hammer before and got bits in my eye 😁
@rcguygarage2 жыл бұрын
Not soft but no need replacement eventually or just buy a new one
@manbearkremer5 жыл бұрын
I wish I knew this tool existed, would have made cleaning up my axles 10 times easier
@rcguygarage5 жыл бұрын
Definitely can make quick work of certain parts and then again the original old school way still works in other areas faster 🤣😂👍
@robertjohnson7744 жыл бұрын
What type or brand of paint did you put on the knuckle?
@rcguygarage4 жыл бұрын
Rust-Oleum 2x Ultra cover Paint & primer gloss black
@SpaceFrawg Жыл бұрын
How much pressure do you have to put on the tool?
@rcguygarage Жыл бұрын
The tool just needs to contact the surface so very little to none
@lawrencenisbett75793 жыл бұрын
You've sold me to it, and I'm a hard sell!
@engjdsАй бұрын
Dont know man, to me it would be better with a flap disk for that.
@rcguygarageАй бұрын
@@engjds flap disk can't get into the back side crevices. This was to just show what it does not an actual viable use every time👍
@engjdsАй бұрын
@@rcguygarage Fair enough, they do look handy, especially for bad welders like me haha.
@aceorace3 жыл бұрын
What's the minimum size compressor needed for this?
@rcguygarage3 жыл бұрын
5 scfm 20 gal just know that if your recovery time on pump is slow you'll kill your pump. This is with ANY high air usage tool. USE WATER SEPARATOR
@pappaclutch32663 жыл бұрын
So this works better then a good angle grinder and heavy duty wire wheel?
@rcguygarage3 жыл бұрын
Yes but keep in mind I was showing the usage of the tool. A good size hammer can take off the big stuff