New Grapple and Third Function Install

Kubota tractor new grapple and third function install
#kubota #tractor #install #PROJECTSWITHMASON

[@joshgibson1222]

favorite part was the dog trying to catch the fly 13 min in haha 😂

[@busman46]

Mason, thank you for your excellent demonstration of installation of the grapple valve. You have inspired me to attempt this on my own.

[@projectswithmason1708]

Glad I could help!

[@robhoffman510]

Nicely done! Thanks for sharing.

[@PetersonFarmsofNashvillePFON]

Thanks for the video Getting ready to install mine on my L3301 Your video was the most helpful out of the several videos out there I reviewed Thanks again New sub !

[@russellaradine9786]

Thanks for the video. Getting ready to purchase a system for my Kubota. The first part regarding the bracket, think those lock washers go under the nuts and not the bolts.

[@kimsmith2239]

Well dang the electrical is what I needed to see

[@ajaibbrar841]

Very good job you did with ease. Keep it up young man!

[@js4455dl]

My dealer installed mine and they put 90s so the hoses wouldn't stick up nice job ps I have the same tractor and crapple. Nice video and job

[@dariussmith36]

Can you show a picture of your's? I would love to see the 90 degree setup.

[@Lannynetz]

Thank you for a great video. This is exactly what I need at this point in time.

[@projectswithmason1708]

Thanks for watching!

[@prow6586]

Thanks for the video. Cleared up a couple of things....🤠👍🍻😄.....LGB....FJB

[@joeyw4442]

One more question........I'm unsure of how to wire the switch to the battery. Can you give an explanation of how you wired it? Thanks

[@joerepic5171]

Great video. I am a bit confuse what happened to the hose you removed from the distribution block. And on the end you say this hose goes here (at the top of the loader which port.

[@SouthernGuy27]

This is a great video. That was either an easy installation, or you made it look easy. I’ll find out soon. 👍🏼

[@joeyw4442]

OK.......I was able to install my Land Pride 3rd function kit by using your instrcutions......I see why the PB hose couldn't be used to hook up to the valve body....wrong sized end of the hose........anyway, my electirc line from the joystick is pretty dang long.......in fact it's long enough to run all the way to the battery.....I had to cut the sheathing and cut the two black lines closer to the valve body to connect them......I left the two red wires intact and wired the fusable link to the postive battery terminal. And connected the two red wires to the other end of the link. Made things pretty neat and sheathed running from the joystick to the battery........One more question though......on top of the valve body there is a white screw on cap.......If you unscrew the cap, you can see down into the valve body......Anyone know what the purpose of that screw on cap is? Maybe it's a way to release pressure on the body and lines running to the front of the tractor so the connections don't get hydro-locked? Says nothing about it on the instructions or web. Thanks

[@GreyFarmTractors]

Great Video! I might would take down the "Borrowed" Street/ Road signs for your next video! Just saying.

[@jakewhitney8201]

Looks identical to the summit hydraulics kit i have except for the control knob. I like the summit one much better. It also comes with the sleeves you said you thought the lp should have. And it was about $400 less.

[@km4fsi827]

I just bought a new L2501, i wonder if the install is the same, it looks like its the same. good video man.

[@york806]

You tend to over tighten o-ring fittings..

[@joemommone3619]

Great video,my question dealer cost land pride 3rd function. Your video very informative. Good job, what state you live in. I'm in West Virginia waiting on my l2501. Thanks

[@rexhavoc2982]

I dont think you put the o-ring side in the valve on the top 2 quick connects. Next time blow compresed air through all the hoses before instaling.

[@joeyw4442]

Why did you have to "replace" the power beyond hose? Couldn't you disconnect the hose at the block and tie it in to the inlet on the valve. Then use a new hose from the outlet on the valve back to the power beyond port on the block? Or am I missing something? Why do you vae to replace the original power beyond hose with a new one from the kit?

[@olim3]

Looking forward to the rear remote vid!

[@bryandarcy9560]

You made a great video thank you

[@projectswithmason1708]

Thanks for watching

[@davidsbigfeet271]

Mason, did you have any hydraulic fluid leaks any where? Your video is great by the way. Will be doing this to my L2501 in a week. You really helped. Thanks...

[@projectswithmason1708]

Nope and it was pretty simple and fast, takes a lot longer while making the video

[@joeyw4442]

After using the grapple for a while now, are you happy with the 60", or do you think the 72" would've been a better choice?

[@projectswithmason1708]

For this size of tractor I definitely wouldn't go bigger due to the weight of the grapple. I am pleased with the 60"

[@jimmythetraveler1212]

What is the part number for this kit?

[@tangoseal1]

Just tight enough to not leak is all you need. Too much and you can over stress the fitting and cause premature failure or injury.

[@johnm.harper773]

Good job! thanks

[@KC-sr1fi]

Love your rottie……❤

[@SouthernGuy27]

Question: Did you have to add any hydro fluid after the install since more hose is added to the system?

[@projectswithmason1708]

yes i did

[@BadCook77]

Amazing job and great video. Can I ask how much the kit and grapple was? Thanks.

[@projectswithmason1708]

I believe the kit was $1100 and grapple was $1800 at the time

[@Gangstercub]

Jesus your cranking on them fittings way to hard.

[@roberthamski5564]

How do you like the terra force root grapple?

[@vikingrobot4179]

I was cringing while he was cranking on those P ringed fittings especially. No need to strip the threads.

[@candidecandide4719]

control mount is pretty cheesey,

[@homestead_diy]

I'm wanting to add a 3rd function to my L3901. Anyone have experience with this kit vs. the other ones available?

[@homestead_diy]

great video by the way.

[@SOJ51.]

Do you have any hydraulic lines going to the back of you tractor for a backhoe?

[@projectswithmason1708]

No I don't, was going to get a backhoe but recently purchased a mini excavator instead

[@bokchoy335]

I was also very interested to know because I hear it changes everything if you have the backhoe. So I'm stuck not knowing exactly what to do. At some point I hope to find that specific instruction change.

[@petezaker1565]

I just installed but had to uninstall bh92 backhoe. Not sure how to do both

[@edkern0749]

@@petezaker1565Look up “Dave Knows How” He has a video on adding additional valves w/ 3rd function installed.

[@tothefullestchannel7517]

You need a vise bud!

[@TheHadjikilla]

How has no one mentioned the doggie?!