New Holland Bring Me Your Baler!!

[@markbrittell2001]

Looks like baby windrows they were baling.

[@biggamehunter9138]

They’d be taking a risk by sending on to Wes but if it did well it would be one of the best advertisements they could ever make for the baler

[@vacone1]

Have to have a demo. 45 years construction. Bought only Caterpillar and Case. New Holland wanted me to demo backhoe, loader. Had for a week demo. Operators used about 4 hours, would not get back in. Finally, I learned the salesmanship never ran or new anything about the Job. Only had company stores. Didn't waste time again with them. Wes is exact correct to check out the third party stories.

[@pdbuilder8212]

Thinking it said our customers come first ? Ha bought a BC5070 last year had around 700 bales through it and the bale plunger pin fell out while it was packing a flake ,feeder forls hit it sheared a inch and a quarter shift off Dealer service truck came out cleaned everything off ,there where all sorts of bolts loose , never torqued down at the factory dealer took it back and went through it hats off to the dealer service team ,running like it should now

[@snowdevil73]

I am not a farmer but its a shame that more companies don't utilize input from farmers that actually use these products rather than rely on an engineer who just graduated from college. Take care Wes, keep up the great videos!

[@kejay74]

That looped knot looks identical to what an IH #46 tied in 1965!!!

[@craigsmith8217]

I liked my 1948 New Holland. I got to know every part on it, including the wheel bearings. I've probably hauled off a ton of needles to the scrap yard. Made out own slide bearings out of bois d' arc.

[@christopherhughes2087]

I will be watching in anticipation as New Holland do very well in europe and I really hope they step up and get an honest opinion from a bailing specialist. its fair enough trying to sell a bailer to a farmer that only uses it once a year but when you using them flat our 24/7 it is contractor territory and a whole new ball game.

[@sethacker2898]

Let's go New Holland send Wes a baler. Let's see the side by side comparison and I'm sure that Wes will be fair.

[@dodgeram15007]

We had this baler at our farm. It is an impressive machine, you do get the bale density in dry first and second cutting hay. That damn crop cutter is definitely a bullshit setup. Lowers the flow of the crop. Just cant beat a hesston(Massey Ferguson). But to each their own. It's not that it's a bad machine but its alot of money and definitely see future electrical problems.

[@welder78s7]

I'm not sure if they still make a large square baler any more but out west Freedman Baler was the baler to have. Granted I was 12 or so but they were well made and a lot of ranches that sold hay used them or Heston. And as always you give you honest opinion.

[@t.c.bowling1934]

Gleaner silver seeder pheasant feeder. My grandma had one, it had a gas motor.

[@lukestrawwalker]

Yeah, the old Gleaners were really made to perform well in one crop only-- dryland wheat. For everything else, it was a kludge... OL J R :)

[@skydom1000]

Néw Holland makes excellent equipment and there balers are great.

[@lsellclumanetsolarenergyll5071]

Now that's a statement !!!!! New Holland better bring it now to you. This would be epic on straw side by side this will really show how much they caught up with KRONE. But I have to say the new blue color from New Holland on those tractors is eye catching like JD, CAT and Chase colors. I hope they stick to one color now like everyone else is.

[@remyrood2215]

Looks like a cool opportunity to try the new holland baler, but I see why you're sceptical about the performance in comparison with the Krone. But look at those tires tho! Thats certainly a big improvement!

[@fabioportelinha8546]

Claas makes that type of knot. Or at least it used to. From what I've seen, breaking billhooks is possible if you have too much tension in the cam follower.

[@thomasleonard1846]

I enjoyed this! There you are, New Holland!

[@jackwillie2729]

Wess you've spoken well you pay top money for equipment and it should perform just as good ...equipment that continuously breaks or dosen't perform in todays high speed and volume is just cutting into profits...best review of a sales pamphlet I've seen on you tube

[@seveneleven5742]

haha like they need the wesley destroy everything approval!!! ;)

[@joshmiller8663]

Wes the only way you'll see a baler for NH is at the dealership.

[@pseudorandomly]

I recall timing an old OLF video; he was moving through very heavy windrows at a speed that amazed me. By actual timing, he was dropping bales every 45 seconds (== 80 bales per hour). The clip only gave me two timings, though; I wish it had lasted for several more cycles. Decades ago, I spent a lot of hours running an idiot-block baler at little more than walking speed ... Wes can bale more hay in about 10 minutes than I ever baled in an entire day.

[@drewbooher1618]

As we say round here , I double dog dare NH to bring Wes a baler

[@tiggerweld4317]

Yes

[@danw6014]

I triple dog dare them.

[@russellpetrie119]

i like this vlog because its a farmers honest review on equipment

[@elliottthiessen1143]

I loooove my new Holland’s . They are the cx 8080 models so conventionals.

[@CarbineAssassin4]

With the knowledge you have for big bailers you should try to get in with a company that makes them and be part of the research and testing of them. Could probably make one that would put perform everything

[@machintelligence]

Use the voucher to pick up some spare parts for the New Holland combine.

[@mtrahan001]

I remembered all the header problems you had . Would be interesting to see them run side by side.

[@lukestrawwalker]

Yeah that pickup drive system was a JOKE on that old NH baler he had... built WAY too light for anything but light straw and maybe alfalfa... OL J R :)

[@farminwithfergusons]

knotter looks like old international baler style with the loop that gets pulled off the billhook

[@russkettner6792]

Come on New Holland get him a baler

[@kevinhickson1481]

Would be nice to see it in the field.

[@gregbird6615]

I’ve had good luck with the small balers but that style operation is huge compared to me. Would like to see a test

[@MessicksEquip]

We have one at etown right now

[@ReverseProof]

Will it stand up to the Krone?

[@MessicksEquip]

@@ReverseProof no idea. We're learnig at this point.

[@markpontes4457]

Send It to Wed You will Know more in 1 week then you would in years! Wes put some skin in the game and tell them if you’re impressed you’ll make a commercial and endorse it! I wonder if Trevor Bales got a card!

[@millerurbanhomesteading8632]

get on the phone M. E. make this happen.....

[@bryanginder5903]

Wes, that's really something that they keep their eye on you!!

[@jacobconfer1693]

I would love to see the new Holland get run beside the krones. Nobody on KZbin has done it. It would be very interesting!

[@danielsweeney6742]

Wes, I would guess it would be like buying a new car. You never want to buy the first one. You'd want to wait a few years to see how it performs

[@milldenhayandstraw262]

Wes run a prototype over here in Western Australia in straw that loop knotter video is different to the system I had the bill hook opens at the end of the cycle to save the billhooks they were a awesome baler to run

[@onelonleyfarmer]

When do you start straw I will come run it on your farm for a week.

[@kluckfabrication5991]

@@onelonleyfarmer that would cool to see

[@lawrencelacenski9781]

onelonelyfarmer that would make for an awesome video

[@milldenhayandstraw262]

@@onelonleyfarmer it was last year before they were released straw season is on now

[@steamfan7147]

I did notice in your recent combine vids, that the Corn in the tank was noticeably cleaner than any I have seen from JD or Gleaner. That has to reduce foreign matter docs at sale.

[@steamfan7147]

For a new product to be successful, it has to do the same, or better, job as its competitor for the same, or less overall costs. I personally think New Holland, if they really do have a better design, they should Pony up and offer you a baler for your fleet in the 2021 season.

[@swainpadgett5633]

Love it Wes! Let's see what they do!

[@ollie-lk5dx]

The ball is in New Holland's court let's if they follow through!

[@ishkur1645]

The new Case baler is fast too

[@0796logsplitter]

Haha love it!! You really don’t give a s**t. No ass likin from Wes 👍

[@69druth]

For a lot of equipment the smaller companies that produce products for a certain field do a better job than large companies that make everything and the support is better in my opinion.

[@clearingbaffles]

At 11:05ish I like the idea of the Jetsons baler no compaction AT ALL! Do they have a Jetsons tractor to pull it? The problem I foresee is fyre unless they have a horizontal system similar to vertical system to motivate the tractor and baler along the ground 😉 New Holland should go one step further and add an antigravity unit to the bales as they are formed so the bales can stack themselves on the stack wagon or even better in the storage you have near the house although I’d bet a lot of MUFON reports would be generated in New Jersey Thanx Wes lovin’ you videos from just east of Krapramento, California the Krapital/Krapitol

[@SledgeHammer43]

Material Agricole is French for Agricultural Equipment.

[@blockmaker3333]

I would love to see the side by side comparison in the field!

[@ivankillins8407]

Hi Mr. Onelonelyfarmer, how are you on this fine Sunday evening. I like your shirt

[@allisterbrown5922]

I would enjoy watching the different between the two balers

[@mikecox9214]

Need to tell them how many bales you make, maybe they don't know. They obviously already realize that you are a potential customer. If they were really smart they would have their engineers interview you as part of their design process.

[@vafaningetnamnledigt1]

The most custommers doesnt bale the amount of bales as you. Here Krone doesn’t sell to many mainly because off the pricetag. They are ok but not to good if you bale 3-4000 bales a year for that 50% higher price. Parts dont come cheap either and Krone do break. Did run a Krone BigM for a few years....

[@jesstroo]

I have owned a Heston and switched to a Krone and I can tell you the parts price is about the same the difference is the Krone will punch ten bales out with Less issues then the heston

[@vafaningetnamnledigt1]

@@jesstroo I have no knowledge about hesston at all. Just CNH and Krone. Krone roundbalers cant compare at all with McHale wich are in a differentiera league.

[@jesstroo]

I do agree with the mchale round balers are in a top league of their own. I still run a nh 648 cheaper baler but a solid baler it has around 15000 bales on it the only issue I have had is the electric sensors for the twine and net actuators. I have a nh tr combine and it is in my opinion the best threshing design and service ability.

[@Ham68229]

Those are small looking windrows, of course this is straw that's being baled. Let's see it bale regular hay crop instead of straw. If NH actually does send you a baler to test out, would be nice to see the comparison between the Krone and NH. Don't think Krone will be beat. If my memory serves, Krone is pretty much designed by farmers, hay farmers. Put it against the Krone, want to see this is. We left NH in the early 80's, (haying equipment), due to exactly the same issues you encountered. Cheers :)

[@ginggur17]

Would be a great comparison side by side. Cmon NH, put the product placement by the side of the Krone. Wes will always call a spade, a spade.

[@jameslonergan4581]

About as much chance of them taking you up on that offer, as Mike Michel getting the Deer X 9. It would be very interesting to see though. A reel world test and honest review

[@jarrettwilliams5992]

Could run an old chain round baler over them little windrows probably damn near as fast as they were going in that video. Not real impressed with the pick up. Surely a brand new baler could handle a windrow that rubs the bottom of the tractor. But nonetheless, im a round baler guy, simple and easy baling, so you can pretty much guess how mind blowing this shit is as far as the technology all the other stuff. Im ready to see Wes put 'er to the test. This will be good.

[@irenesilvers7096]

Nice video, thank you.

[@dehavenfamilyfarm]

I sure had to laugh when you read the part about their customers being important to them. CNH left me high and dry for over 4 months waiting for backordered parts on a brand new tractor last year. Meanwhile, the tractor is sitting torn apart in so many pieces you couldn't even tell what it was. Some dealers definitely care about their customers, but big corporations could care less! Let's see if they will step up and redeem themselves in front of everyone they have done wrong- I doubt they will lol

[@2cylinderjohndeere720]

It would be worth trying out but you know what you have with Krone. Once you get a Krone Big M mower there will be no looking back!

[@kieranosullivan02]

50 foot krone tedder and rake then? Haha

[@damjord]

If New Holland really believe they have a good baler they should provide you with one. Everyone knows how unimpressed you've been with their older balers, so if the new one compares favorably in some aspects to the Krone, and leaves you impressed with how far they've come, then surely that's got to be win-win situation.

[@blacksheep9734]

I remember a time before the speed rower. Where you swore by new Holland

[@foolton468]

I hope they send you one to try. If it is that good they should have to worries about it standing up krone.

[@machintelligence]

On the loop knot, it looks like if you pulled on the short cut end of the twine, the knot would untie. (Not that you would, of course.)

[@two-strokesmoke7289]

Wes always has the best ideas.

[@jantkb]

With the new HD Square baler, what density can you get? How much does 3*4*8 weight?

[@robertstibz9506]

I would put money on New Holland not excepting your offer, it won't beat your Krone balers. But they won't dare put it to the test with you lol, I just Dare them to :-)

[@evanstoll4656]

You should see the new gen 5 krone balers in action, they are awesome but wont be released till later 2021.

[@s.pursell8901]

I really think you should get the Krone Pelletizer. You'd make a killing in these parts. Everyone around here has a pellet stove.

[@youngdude7500]

That pellet maker is a disaster. Moves over the field at 2 m/hr. Better bale the stuff and make pellets in a stationary installation.

[@akersjon278]

So there must be this new risktaker guy in the New Holland managment team. He probably likes to rock climb and base jump, cause why else would he send this promo pack to you Wes...lol! Sending a promo pack for the "Knot master" to the OG "Bailing master"...

[@AlextheDutchDairyfarmer]

👍👍Really Hoping New Holland picks up the glove.

[@Northern_Farmer]

That would be interesting

[@jimarcher7665]

Monumental if it works well and monumental if it sucks ass LOL. Wes I wouldnt count on that ever happening, they want outcomes that they can control

[@mattbrachtenbach2172]

We ran new Holland equipment and we always thought they over engineered everything thing. From their swathers to their round and square balers.

[@jimbennett6296]

Would love to see the comparison!! We are livestock producers in Ontario We went to the Krone Comprima round baler a few years ago Nothing compares !! Jim Bennett’ Ontario Canada

[@JDfan1990]

Those knots look like the knots my old b46 and 56 international small square balers make lol anyone that knows the old IH knotters knows how well they go when they get worn...

[@samriemer3968]

My biggest bitch with new Holland is there lack of availability of combine parts. I run a cr9040 combine. Takes my dealer 3-4 days in most cases to get even cutter bar parts, knife sections and guards, for my 740-25cf new Holland flex header.

[@jeromemiller5262]

Someone in marketing just lost their job because they sent that to you! 😂😂😂 I’d love to see the side by side, it would either solidify or liquify their new baler.

[@khalidmasood619]

They expected. Mr pandy was a sell out like Cole or Larson fake farms

[@movingon4211]

Gleaner is just a galvanized grinder....lol

[@calitrainman]

I'm not gonna hold my breath that they show up with one for you to run

[@jankotze1959]

You handled the scenario excellent, if there is any credibility and believe in the claim of being the best in the tests done then there will be a baler, hopefully, Krone impress me a lot and on the other hand I would like to see that you are impressed by the new New Holland if they bring one

[@theokusters7491]

Local NH dealer has a new big baler340 sitting in the yard for over a year and couldn't sell it. Last week I saw it again but now with a (retrofitted) hydraulic motor on the right side where the pick-up drive is.... People know what the problem with those balers is....

[@ericrichwine7781]

That would be awesome!

[@OleRustyTractor]

I would like to see a demo of machines ran in the Dakota’s where they can run these machines side by side for weeks to compare reliability and speed through every different grain you can think of. Not just straw on the east coast bouncing through 100-300acre fields by some guy that can’t keep his own shop clean

[@bobopsahl7415]

Wow what a ZINGER OF A COMMENT that was !

[@kennethhamabata2338]

love your hat

[@amsimons29]

Its funny watching your video now it has new holland commercials. It would be great to see wes run a new Holland against a krone baler

[@Rooftopmatty]

There is very few company’s that will let someone get a demo and be able to post it on KZbin with an honest review, the only dealership who I’ve seen do that is the agco dealer that mike Michelle shops at in canada

[@pureneglect4702]

Personally I think new Holland should let you run one for a full season. That way you'll find out what is likely to were out and will be put through a proper test that you can compare to the krones

[@Blasterxp]

You should lease one, and run the balls of it. Every error, you let them fix it. They will know all mistakes the bailer will make.

[@calebbisson4577]

But then he'd be paying for something that would potentially slow him down. If he leases it it has to make money

[@johnvady3990]

I think the test was made in France (krone, new holland, fendt) in very dry condition this year (weat straw)

[@thesilentg3941]

Well if new holland really gives you the baler, then i think we can truly expect a word end :D

[@dexterscott33]

If NH has any nuts at all, they will send you a baler. If they are that confident in their product they should feel comfortable with the risk of sending you one bahahaha. And based on the comments below, a video with thefarminglife would be interesting in deed. It would be like America and North Korea coming together and shaking hands.

[@Gustav4]

it is so cool the new one. (the european model)

[@glennkingsbury1005]

Based your experience ! Thanks. Again !

[@jimpetersen8900]

Good for you Wes,tell them like it is

[@chadtheartist5081]

New Holland makes a claim, Wes counters........New Holland, the ball is in your court.

[@mesh1248]

Lmao i love the way you take apart the new Holland video and show us what you think is good or not

[@RoisinT2]

The baler it self could be kinda alright as was the last one i remember you saying, but the pickup.. that was beyond trash. If they havent done a completely new one for it, i think it isnt even worth of a test.

[@johnsweda2999]

Why do you prefer Square bales and not round bales is Square bales better?

[@sjaakvanengelen4072]

its a good baler .try a demo

[@youngdude7500]

If you like camless that much.... then you must really hate Krone VFS with cam and bearings that need to be replaced every 13000 bales.

[@genechronister7085]

Don't tick off the lawyers

[@daniellepoidvin7592]

I hope they send u one. Mabe two so u can use one for parts when the first brakes down