With this technique you will do incredible work!

[@jayminor9757]

Great idea! Simple, inexpensive, quick and works very well.

[@darioromano5324]

Fantastico.... sempre cose interessanti nel tuo canale

[@Armanufacturingskills]

Amazing video

[@sharkbaitsurfer]

That was beautifully done and such an incredibly useful technique

[@deniscortes9200]

AWESOME!, GOOD IDEA. THANKS.

[@centurion2185]

Thank you for sharing this great technique.

[@claudiovandoni7878]

Molto interessante bravo

[@bobguarnieri280]

Excellent!

[@Micha-hw9ob]

Naprawde super rozwiązanie !! Dzięki 👍👍👍

[@juanpabloramirez6565]

Gracias por compartir

[@RustyInventions-wz6ir]

Very nice work.

[@theoutbackshed]

Great idea, I shall store that up for future use.

[@DerbederBiri]

Bravo Türkiye den selamlar 🎉

[@Armanufacturingskills]

You are doing unique work

[@fabricepoulain02]

Excellente idée. Je suis abonné à la chaîne et j'apprécie beaucoup. Merci 👍👍👍👍👍

[@un-factory]

That's good 👍 👍 👍

[@ورشةاولادابووحيد]

تحياتى لك.. افكار ممتازه ومحتوى القناه مفيد ‏‪

[@juliocesarmarreroleal8913]

¡Excelente! Felicitaciones.

[@СергейВечканов-у7з]

Bravo!

[@NJKTJ]

Thank you so much sir for this new idia

[@Massimo68ac]

Magico! 👍👍👍👍👍👍😎😎💚💚🤗🤗

[@steveforbes7718]

All things considered those are some slick tricks. It is true that you may lose concentricity but, if can be reestablished when the part is first run. As long as the clamp and part are not removed and turned around then that won't change. However, for the objects shown that really is not an issue. This idea does have a lot of uses if one thinks about it.

[@lotharprimas812]

Sehr sehr gute Idee. Vielen herzlichen Dank. Mfg.Lothar aus Haburg

[@ramiromarroquin3021]

muchas gracias MAESTRO

[@louisd1968]

😀 tres tres bonne idees merci

[@Ник-л9х6ъ]

Уровень ПТУ 😅😅😅😅😅

[@garygruber1452]

elegance is in its simplicity.

[@Walker7745]

Вот именно для этой цели я сделал маленькую проточку на кончиках кулачков. И теперь любая шайба толщиной свыше миллиметра легко зажимается прямо в кулачки.

[@pier3461]

Ciao, sempre ottimi video! è un pò di tempo che ti seguo, hai anche una pagina fb e/o instagram?

[@newtech5042]

Ciao, ti ringrazio... Al momento ho solo il canale youtube, comunque non escludo la possibilità di creare qualche pagina su altre piattaforme!

[@annacalise8336]

Making a small grooved adhesive plate works really good too with super glue, but I like this idea even better because you can keep the nice surface appearance without worrying about the heat turning it while removing...

[@pawekowalski7469]

👍👍👍

[@wawansetiawan4042]

Mantap bos.👍👍👍

[@LeoA-t4z]

Gracias ahora si me dejaste anonadado lo pondré en práctica 👍

[@GiovanniSimiani]

Ciao, una domanda, in questo modo si può sfacciare e tornire il foro ma per ridurre il diametro esterno? C'è un modo altrettanto fantastico quanto questo?

[@newtech5042]

Ciao, se devi tornire il diametro esterno di una rondella, puoi prendere un bullone (le brugole hanno un diametro più preciso) e stringi tra due dadi la rondella. Se hai bisogno di un diametro non commerciale, devi tornire un tondo e filettare un'estremità per stringere la rondella con un dado o bullone per tenerla solidale al supporto appena tornito.

[@GiovanniSimiani]

​​@@newtech5042​si la rondella è 30x38x2 mm e la devo portare a 30x36x2 mm quindi se non ho capito male c'è da costruire un supporto con dado o qualcosa di simile che pressi poi la rondella. O meglio un supporto ad espansione?

[@newtech5042]

Dipende dal materiale che devi lavorare... Se è un materiale duttile, devi stringerlo a pacchetto, se il materiale è ad esempio ferro o acciaio, puoi utilizzare anche una pinza ad espansione.

[@GiovanniSimiani]

@@newtech5042 alluminio, ok grazie mille!

[@GiovanniSimiani]

​@@newtech5042 ho realizzato un porta rondelle con un foro centrale da 6, ne impilo 8 insieme e poi con un perno le stringo a pacchetto e le lavoro esternamente. Funziona perfettamente! Grazie!! 🥰

[@AlexandruMitroi-u5u]

Mulțumesc frumos pentru cea ce ne inveti pe unii dintre noi Respect si admiratie Te rog daca sti spune mi cum fac un nut de pana la interior pe strung Mulțumesc încă odată

[@williammorris1763]

You know the weirdest thing about watching these videos and knowing what everything feels like in your head.😂

[@DigitalVideoFromOz]

You lose accuracy when you remove a piece from chuck and later re-insert it. There is also accuracy lost in closing the saw cut by tightening the jaws. Maybe its not enough to matter in some instances.

[@localele1]

And if you use the version with a shoulder against the chuck it gives you a repeatable reference for multiples.

[@JimBrown-zj2rz]

As a time served machinist I must tell you that you are only half right. what you missed is that you need to mark your fixture at number 1 chuck jaw so that you can put your fixture back in the chuck in the same place that you machined it every time to keep concentricity.

[@newtech5042]

Hi, you're right! However, this is just an example, so I didn't want to waste too much time with the details... In any case, I thank you for the comment which may be useful for users.

[@retrotehnologii]

Профессионалы так не делают, для этого существуют сырые кулачки с выточками... Но для гаражных хобистов пойдёт!

[@НиколайКалугин-б3г]

У профессионалов два, три,четыре десятка комплектов кулачков (пропорционально стажу работы) под различные операции, гаражные хоббиты могут только мечтать о таком изобилии .

[@enricotosco]

🎉💪💪💪👏👏👏

[@csakanydavid7427]

👍👍👍❤

[@lubovmeshkova1458]

Awesome technique. How to made a ring from Teflon with a thickness of 1mm and a diameter of 35mm, dephth - 5mm.

[@ZlodieIzZaholustia]

Метод рабочий! Но также для этого можно использовать токарный патрон меньше и сделать на нем микро выточки в кулачках

[@СергейАли-у6е]

смять шайбу можно, приходится осторожничать , а в оправе она плотнее сидит, не пережмёшь, особенно медяшки

[@sky173]

That's very good. I wonder how to make a .002in washer/spacer

[@mikebowling3228]

I could tell you how, you need to make several out of shim stock, finish the ID while holding on the OD then do not unclamp and put a bolt through the ID to hold while you remove the OD clamp or bolts then finish the OD

[@clivelee4279]

An elegant solution , however just superglue the washer to the ends of the jaws ( it helps if the jaws are clamping something) , the washer doesn’t as a rule need to be concentric , hold it in place for a few moments with something in the tailstock , good enough for rock and roll .

[@jand6329]

Laudetur Iesus Christus 👍👍👍 Deo gratias 👍👍👍

[@peterfromchile634]

Es un antiguo recurso, usado por torneros para fabricar golillas (washers), también se le conoce como "camisa partida" (clamp). Generalmente se fabrica de bronce, material que es más "blando" y rápido para tornear.

[@christophersheward9266]

Would you call this a split collet ?

[@JSmith19858]

This is what soft jaws are for and do. A lot of these 'simple hacks' are unnessesary with a set of soft jaws used correctly

[@Sparide-y6m]

Non facevi più subito a fare la rondella?

[@brunocalvia5831]

Dov'è la novità?

[@MonicaDenis-wr9jj]

saludos vean y aprendan

[@sergeypetrov9499]

А что такое-опустить шайбу?

[@НиколайКалугин-б3г]

Возможно уменьшить высоту ( толщину) шайбы?

[@ellieprice3396]

How do you "lower" washers? Wrong word.

[@newtech5042]

Hi, sorry for my bad English, what is the right word?

[@robertsanders1916]

try making them out of steel.

[@douglasfeilen4344]

I guess you mean facing off!

[@mariobenedetti9714]

Guarda che esistono i morsetti teneri, per fare queste cose. Comunque anche il tuo metodo e' valido, anche se molto macchinoso.

[@newtech5042]

Ciao, hai ragione... Ma cerca di immedesimarti nel hobbista che vuole ribassare una singola rondella, pensi davvero che comprerà un set di morsetti teneri per quel lavoro???

[@WeebRemover4500]

so simple, i feel stupid

[@СЕРГЕЙВОЛОТКЕВИЧ-щ4й]

это если их 100 штук надо. из за одной не будешь делать

[@JohnBrown-hx5oy]

Would have liked to finish video, but couldn’t because of the irritating music😢

[@steveforbes7718]

Turn the sound off dimgbat!

[@КузнецовАлександр-й6ь]

Древний способ ! Старо как мир !!!

[@НиколайКалугин-б3г]

Уважаемый! Не все такие древние как Вы! Молодые начинающие "наркоманы"металлообработки имеют право знать и древние способы камлания с металлом.😊

[@mikebowling3228]

What a waste of my time..

[@carlosalbertobarbosa7568]

Se for muitas arruelas de diametros diferente aja matérial.

[@franciscomartindelucia782]

Primero aprende a hablar, girar????