Ultimate Zero Clearance Throat Plate with Replaceable Inserts

[@lwaynes1]

One quick question, where do you find 1/4" mdf with melamine coating without having to buy a 4'x8' sheet? I have exhausted all woodcraft related sources in my area (Dallas/Ft. Worth, TX) without success. Please, would like an answer from anyone that knows a source, Thank you, Wayne Standerfer Duncanville, TX

[@NextLevelCarpentry]

Hey Wayne, Lucky for you, you're in a large metropolitan area where there are surely dozens of commercial/light residential cabinet shops. Stop by any one of them with a dozen donuts on a Thursday morning and ask for a few pieces of scrap. In my experience, most shops throw away more scrap in a week than I use in a year and, with just a little bit of luck, you'll find a shop who will gladly trade maple with sprinkles for mdf with melamine! 😉😎

[@lwaynes1]

Thank you for this suggestion, will certainly follow up. Just FYI - the cheap Chinese 60 degree router bit listed in supplies will not fit an American made Bosch 3/8 router collet chuck, Chinese 3/8" is larger than our 3/8. Thank you again, Wayne Standerfer Duncanville, TX @@NextLevelCarpentry

[@jeffdeluca1153]

You're never boring friend! Making these videos takes a lot of time and effort and should be appreciated by all. Keep up the great work! Jeff

[@garryjohnson5310]

Certainly appreciated by me. Never tire of watching a master craftsman in action.

[@dmcarpenter3097]

I know this guy Jeff, bought a router off him years ago. Crazy to see we watch the same Craftsman's videos. What's up Jeff, how's the kitchen coming?

[@alsmith4791]

%%%%%%%%%%%%%%%

[@jeffdeluca1153]

DM Carpenter Small planet! Well I'm working on the bathroom right now but doing well, hope you are!

[@terryt2910]

Gotta love this much detail. This is teaching, not just showing.

[@cajunx1113]

You produce some of the most informative content on KZbin. Thank you for all you do!

[@NextLevelCarpentry]

You're quite welcome... I appreciate that you watch and comment here!

[@DanielWhitcraft-m8d]

Great job! Every time I watch your videos I learn so much and I’ve been a carpenter for over 30 years. Again great job!

[@NextLevelCarpentry]

That right there is the ultimate compliment... thank YOU! Best, Matt

[@hytekrednekbama4400]

I first saw these type inserts watching the legend, Norm Abrams. He had a table saw episode that mentioned these. I looked and looked, finally found one from Charles Neil woodworking. I am glad Norn put me on to these. I miss Norm! I wish he still did videos every week.

[@hyperborean.]

Thank you for sharing your knowledge and experience with us. I believe what makes Matt different from other similar channels is his magnificent ability to relay his knowledge clearly to the viewers, without becoming boring. Enjoyed every minute of it. Thank you!

[@VertexCarver]

Wow... Thanks! This was next-level kind of you to make. Blows my mind a bit that he made an entire build tutorial for something he already got sorted. If you happen to come across this comment just know I highly appreciate it. ^^

[@jerry-p]

You're a fine teacher, Matt, and your in-depth instruction, coupled with your dry sense of humor, keeps the wood from warping and passes on valuable knowledge. I appreciate the work you put into your videos.

[@NextLevelCarpentry]

Appreciation backatcha Jerry... thanks for watching and commenting on this one!

[@wmcwings4343]

I just received as a gift my first table saw. Looking through various videos I stumbled across yours. I have to say this has been the most educational, well produced and useful video I have watched in a long time. Excellent job! I only wish you were my neighbor. Keep 'em coming.

[@TheVideoGameVault]

I love the level of detail you have in your videos. It really helps noobs like me really understand the how and why.

[@NextLevelCarpentry]

Thanks for saying... you can always post a question here in a comment if there's something I overlook in a video. I try to include all that detail but sometimes have a blind spot about something that seems obvious to me but not to someone starting out...

[@GregsGarage]

Great looking and great functioning piece of kit Matt! All your points regarding the difficulties of manufacturing a one-size-fits-all product are spot on. This is a wonderful solution that anyone can tackle for the saw opening they have.

[@NextLevelCarpentry]

Thanks Greg! You know details of those difficulties more than most, including myself, so it's nice to learn your approval of this alternative 👍😎

[@IH1940HAY]

Thanks so much for sharing your super sable saw insert. I really appreciate your detailed and convenience narration of the construction.

[@kevingeaney7741]

Lots and lots of very helpful supplementary information in addition to the outstanding zero clearance plate video! Thanks.

[@milesodonnol4456]

"copacetic", "antidisestablishmentarianism", "in situ" Hey, you're my kinda guy. I recently cut some aluminum on the table saw; a small bit dropped into the blade well and shot out like shrapnel. I was standing to the side so it missed me, but the way it hit the ceiling was impressive. And it got me to thinking about zero clearance inserts. Yours is the best, of course. Thanks for a top notch video!

[@biancaw.5987]

Another fabulous video, Matt! I learn a ton every time I watch you do something. Thank you!

[@daveh7945]

You son of a.... now I have another project on the list...🙃 great video. very clear and thorough

[@marcuspullan1142]

Another great video. Sometimes I get lost in what you’re saying, but when you show the step, I get it.

[@JimChampaigne]

I watched your video on my 81st birthday. Been woodworking since I was 15 years old. THANK YOU for this very well done presentation. I too added my router to my new Grizzly hybrid table saw. Jim Champaigne Elkhart, Indiana USA

[@NextLevelCarpentry]

Happy Birthday Jim! You've got a few years on me... I was 5 years old when you started! Glad to hear you are still interested in woodworking and hope you have many more years of enjoying it!

[@travisg1759]

Thanks! I love the detail of your videos to the point this is the first time I've ever bought a Super Thanks. It takes normal KZbin videos to the next level and so few do.

[@NextLevelCarpentry]

Thanks for the compliment Travis... And thanks for making Next Level carpentry your Super Thanks guinea pig!

[@inygomontoiya]

I have to agree. The attention not only to the detail of the work, but the detailed explainations of how/why are amazing. Kudos.

[@NextLevelCarpentry]

@@inygomontoiya much appreciated!

[@bobstovall9570]

If you wish to commercialize the production of these inserts you could simply manufacture the blanks of an approximate width and length with the dovetail groove and inserts and allow your customer to tailor them to their specs with a disclaimer that you assume no liability for any injuries or damages that result from your product having been modified in ANY way. That should also eliminate your liability issues since all you are providing are raw materials that the purchaser can use as (s)he sees fit. This is, easily, one of the best videos in this genre. I feel certain that Stumpy Nubs would approve.

[@jim7smith]

Outstanding display of ingenuity including the ut ohs. I can hardly wait to get some of these made for my Grizzly 1023 which I acquired 4 years ago second handed. I was getting nervous at the end but you finally showed how to make the initial cut in the replaceable zero clearance insert! Thanks so much, I watched the whole thing!

[@tedtolentino4955]

A really well made video, IMHO. Yes, long, but with detail that would otherwise leave one wondering how it was done if not included in this tutorial. Sorry to those whose attention span or patience is limited. I have an old table saw that I am hoping to rehabilitate and restore and this project for a zero clearance throat plate is a perfect update for this old saw. Thanks, and don't be intimidated by the comments. You have nothing to be ashamed of and plenty to teach us novices.

[@markhedquist9597]

These are super nice inserts! And your step by step process was well worth the watch. I started upping my carpentry game about 5 years ago after 25 years of being a ho-hum carpenter. It's videos like this that have helped me improve my skills and methods. I greatly appreciate your thoroughness of explanation. AND, I will be making some of these inserts to replace my cruddy plywood ones that ain't that great.

[@NextLevelCarpentry]

Kudos for acting on the inspiration/motivation to take your carpentry skillset to a next level of your own Mark! I'm honored to be part of that journey and forsee a bright future for you as you move to the front of the pack!

[@Tim1967-o7j]

Best video and build for a throat plate anywhere. Don't waste time on anything other. Spend it building 3 or 4 of these and end the problem. At least. You will have a perfect throat plate and time to think about project solutions and builds. Thanks. Great information and video.

[@lonwhitmer7771]

Nice video. I have been making zero clearance insert out of melamine for my unisaw since 1984 in a simalar fashion And cry when it's time to make three or four more. This is a better setup and easier to keep a fresh clean cut in the plate. One last time to cry. Hallelujah . Thank you

[@NextLevelCarpentry]

I find that the bigger stack of spare inserts I make the less 'painful' it is to swap them out so I'm always using ones with a very tight zero clearance. You're quite welcome too, Lon!

[@fuddly123]

Wow !!! that is quite the precision made Insert , Bravo on the fine work !!!!!

[@gmyrick49]

Great video as always. My Unisaw is 46 years old. The "riving knife" never worked worth a damn. Got rid of it right away and moved on. My wood shop teacher taught me to stay out of the line of fire. Works for me.

[@NextLevelCarpentry]

Yours is 3 years older than mine... I know what you mean: the splitter/riving knive/ anti-kickback that came with my was a gangly/wobbly affair that was far more danger than nothing at all IMHO.

[@kencross25]

I'm a repeating all the previous "Thank you". I copied your detailed instructions, which you made very easy for me, and made three "Zero Clearance Throat Plates" for my Delta Contractor's Table Saw Model #36-725T2.

[@jeremyhuggins8796]

Never got bored with the video. I actually backed it up several times to see a step performed again. I love the manner of your presentation and explanation. Subscribed. 'Jesus Saves'

[@NextLevelCarpentry]

Thanks for watching, commenting and subscribing Jeremy... much appreciated!

[@firewoodsteel]

Nothing boring here, a great teacher giving some great advice. Just tan put of HDPE for other projects but I'll be sure to use this jig for future work.

[@BrianGalyer]

I wish someone would make me one of these for my DeWalt DWE7485. All I can say is you are very clever and talented man. love the videos,

[@doughall4901]

Great job of showing and explaining how you make copies of the inserts!

[@kennyshipman7136]

Another great shop tool build. Thank you for the depth of detail you use for all your videos.

[@NextLevelCarpentry]

Youbetcha Kenny... thanks for watching and commenting!

[@norm5785]

Great work. Thank you for sharing. Everyone stay warm, safe, happy and healthy. From Henrico County Virginia

[@StratOvation]

LOL, Hard to argue with the choices of a Certified KZbin Diva! Great Instructional video, Thanks for sharing this!

[@NextLevelCarpentry]

I know.... right? 😂

[@scottgutauckis4615]

My biggest takeaways form your videos is not what you are building but how you are building. Your techniques are not widely shown elsewhere and usually leaves me with a "Why didn't I think of that". Great video.

[@NextLevelCarpentry]

Thanks for watching and commenting Scott... since I'm almost entirely self-taught I think the way I approach things is 'outside the box' some folks end up in by attending schools or courses that can inhibit free-range thinking that ends up in a different paradigm. It's mostly good but I'm sure I'm missing out on some mainstream ideas that would be better in some situations...

[@passerby6168]

Really like the idea of having more than two throat plates for different blade thickness, dados etc. This seems very functional. Thanks for sharing.

[@NextLevelCarpentry]

I agree and have 20 or so to prove it! Best thing is that 20 inserts for this design are easier than 2 of most other designs.

[@ederorellana9919]

I finished my inserts this weekend and I’m so satisfied with the result. Thank you for the video. This is exactly what I needed.

[@NextLevelCarpentry]

Glad to hear it... and kudos for tackling the project and seeing it through to completion!

[@joedance14]

Beautiful work! I had thought of something like this, but never got around to it. You make the whole process much clearer. Thank-you very much!

[@lvmadsen]

You are now my favorite youtube Diva !

[@lvmadsen]

And then i watched some more - holy crap some nice learning ! tywm ! Great video... guess I have to upgrade my router table a bit before I can do this... ( just slapped together fast with some plywood )

[@audreyhargett3094]

I watched to the very end... even though I was supposed to be sleeping. I just had to see the finished product! Thanks again for another great educational video :)

[@clutions]

I just spent an hour watching this video not because I plan on making a ZC insert, but the many tips that were thrown in! THANK YOU!

[@Steve-od6hi]

Totally awesome idea and video, much better than what I have done before for myself, Big Thumbs UP !!!

[@Oldiesyoungies]

this is one of the best videos on youtube

[@NextLevelCarpentry]

Thanks for saying Stan, much appreciated! Put a lot of work into filming and editing this video so it's always nice to hear when viewers appreciate the end result!

[@jeffbourne6015]

A superb video demonstrating how to make a zero clearance throat plate with replaceable inserts. All aspects of the construction process were fully explained along with many useful tips that could be used in similar situations where real accuracy is required. Many thanks for sharing such knowledge, showing us why attention to detail is so important and how to achieve it using basic tools and equipment. Moreover, thanks for the time and effort to compile and edit this highly informative video.

[@NextLevelCarpentry]

Thanks for such a glowing review, Jeff... much appreciated. Knowing that viewers like you find value in this sort of 'deep dive' videos is gratifying to content producers!

[@blaineverhelle4104]

It's amazing! I've been looking for one of these zero clearance plates for my saw and I can't find them anywhere. My saw's weird. It's like 3-1/2 by 15-13/16 long. I saw your video pop up and was shocked. It's like yes, this is what I needed. Thank you sir.

[@NextLevelCarpentry]

Woodworkers like you are who I had in mind when I decided to produce this video Blaine: those who want/need a very useful/functional zero clearance insert for their saw but can't find one to buy... have fun with the build and enjoy using it when you've made it!

[@blaineverhelle4104]

@@NextLevelCarpentry👍

[@robertj6477]

thank you very much for taking the time to answer my question and that makes great sense thank you very much

[@kennethbrooks9818]

Very, very thorough presentation. Thank you. It was worth the time to foresee all the details well considered.

[@frederickburns1739]

I watched it all and gained some pointers!

[@barrydoxseyuk]

Just what is needed. Love the last section, using the fence as a hold down👍

[@Bosk2420]

This is THE BEST instructional video I have watched (and I watch a bunch of them) If memory serves, I may not be able to use the information, as I think my plate is thinner, but I will be subscribing, as I am sure there are more tips and instructions I can use with this exceptional narrator.

[@NextLevelCarpentry]

Glad you like this video! The best thing you can do to thank me is to share and spread the word about Next Level Carpentry on KZbin! 😎

[@coachwalrus3158]

Always a pleasure I had a funny ideas you were going to come up with something I checked Greg’s site for quite a while and it never came into play. You don’t disappoint

[@bryanspiers]

I see people saying great job - I will concur - great job - great detail - keep up these great works !! Thank you!

[@michaelgeraghty8699]

You're a breath of fresh air excellent video. Thanks Mick

[@robertlewisvideo]

Awesome video !!!! Love your sense of humor in your videos as you show your expertise with safety in mind.

[@nelsondog100]

I asked, you answered in a way I never thought possible. Thank you so much and I’m happy to say, I’ve subscribed. 😊

[@NextLevelCarpentry]

Awesome! I meant what I said at the start of this video because so many viewers like you have asked over the years... glad to help out and thanks for the sub!

[@MrMutzikatzi]

Very professionally made video! I enjoyed it very much. Your advices will help me a lot! Thanks to you from good old Austria Europe!

[@erictownsend4236]

Hi Next Level Carpentry, I bought a Powermatic 66 table saw in the ? late 70's. Did not like the supplied throat plate. I bought the original version of the throat plate you showed. I LOVE it. As you mentioned that co. went out of business, so I couldn't buy any more replacement strips. The original strips were made of wood. Now I make my own out of scrap hardwood. Zero issues with the plate I have. I built a rack to hold various inserts for thin kerf, 1/8" , various dado widths, blade set at 45 degres etc. I even have inserts for the same blade , but for different hight cuts so it is a tru zero clearance insert. I mark on the insert what blade it is for with a sharpie. My saw did not come with a riving knife/ spliter either. No issues cutting very small pieces, improves dust collection. No down side that I have seen only pluses on this design! All of the zero clearance plates I see on the market today are a flat plastic plate shaped to fit what saw you own. They are pricey! This is the only way to go! Great Video! Thanks Eric

[@Tito1984]

I recently picked up an old Rockwell Unuisaw that is in fantastic condition with an upgraded fence. Can't wait to get it going, need to make room in my shop and get the 230V outlet first. Throatplate with removable rectangular slides, what a great idea! Just went to Gregs website and I don't see any of his throat plates for sale.

[@davidquirk8097]

Thank you for the in depth video. I appreciate how much effort it takes to produce content this good.

[@NextLevelCarpentry]

Thank YOU too, David... please share NLC content with friends and on social media to spread the word? Best, Matt

[@JamesWilliams-en3os]

I’m a new subscriber, thanks for this excellent video. I have been making my own zero clearance throat plates from plywood for several years, and am a firm believer in their utility and safety. I need to make a new throat plate for a new thin kerf saw blade, and was not loooking forward to having to fabricate yet another throat plate, when I stumbled across this video. Now I plan to follow your method to make one throat plate with multiple inserts instead.

[@mikesimpkins7919]

Great Video. Thank you for showing your process. I will be making my own.

[@nonfacebookuser5867]

Thank you so much for what you do Matt. I will be making a few of the zero clearance inserts for my Net. That is a soon as I can get in my garage workshop. 5°F, is much too cold to work out there. Keep up the great work!

[@NextLevelCarpentry]

Have fun with your project and we'll both hope it gets warm enough for you to work in your shop sooner rather than later😎

[@jamesoddsends4483]

I made one of these zero clearance inserts years ago just after I bought my 10" contractor saw. Nice vid.

[@mwoody4560]

New to the channel. YT advertised this on my home page and I decided to take a look. I’m in the same boat, my tablesaw is no longer manufactured and throat plates no longer available. The saw is great and will probably out live me. I could buy a Saw Stop which I really like, but I just don’t want to spend the money when I have a perfectly good tablesaw already. Plus with nearly 40 years experience, I haven’t cut myself on a tablesaw. My mentor drummed into me how to safely use a tablesaw back when they had a lot fewer safety measures. Anyway, I’ve made many inserts and have experimented over time. I have been considering something similar to this and I really like this approach. I’ll probably reuse a lot of it. The biggest change will be perforations in the throat plate to improve dust collection. I know you made a comment on that as why not to include a finger hole to aid in removing the throat plate. But I’ve experimented with this and perforations improve the dust collection. They also supply a slight suction to hold your cut piece down to the table, which is noticeable when cutting thin stock or laminate.

[@NextLevelCarpentry]

I just don't like working with a left-tilt saw... annoying that the fence needs to be re-zeroed any time blade width (or dado stack) changes... a total deal breaker for me! There's a lot to like about SawStop but they're all left tilt! 😡 Interesting what you've found with perforations in the throat plate for slight suction when ripping laminate. I may try and drill a string of holes through one of the 3 from the video for just that application.

[@OORAH659]

do you have a video of how to use a dado. I like the method you use to cut the dovetail and show us the ruff look. (especially the orange board)... We The Few will never give excessive emphasis to (something) you showed us. Our and your attention to simple design is never unnecessary. ....OORAH!!

[@NextLevelCarpentry]

I use a dado blade in various videos on the Channel but never did one dedicated to the topic. I think a couple videos the Pallet Door Build Series probably have the best look at it though...

[@Spoon819]

Matt, I love all your videos and greatly appreciate the time and effort you put into them! The information you share with us is priceless, and I sincerely thank you for all your hard work and time. This video was no exception. I do have one concern in regard to your health. I have always been told to wear a mask when cutting or sanding MDF. I have seen you working with MDF without a mask on, and while I understand for the sake of the video, it is more convenient I worry for you. All of us here I am sure would not mind if you wore a mask when working with MDF.

[@josephhaddakin7095]

I saw Norm using one in an old New Yankee Workshop episode & was bummed when I searched online & couldn't find any. Thanks for the indepth how-to video. I have an xacta jet 10 inch left tilt.

[@NextLevelCarpentry]

Being bummed out that such a great product was no longer available was my motivation for putting this video together because the zero clearance insert is invaluable for so many projects IMHO. Hope you're able to make one to fit your saw...

[@dmcarpenter3097]

Would have loved to have known you when I was growing up, learned so much from you over the years.

[@NextLevelCarpentry]

That would probably be a good thing because then, in that parallel universe, I may have actually grown up too 😉🤣🤣 As it is I keep wondering when the whole 'older and wiser' thing is supposed to kick in!

[@robertcote5398]

Call me a nerd...I enjoyed the patience, precision and meticulous approach- like rear woodworking. Great kaizen. I look forward to seeing you cut that tomato...GREAT VIDEO!

[@NextLevelCarpentry]

Watch for a video showing how to slice tomatoes in the next video from Next Level Coventry on the late night TV Shopping Channel "but wait, there's MORE...!" 🤣

[@jedevans1]

Brilliant video. I’m off to the worship to make mine now. Thank you..!👏

[@lounackman6104]

I'm fortunate enough that my Powermatic 66 came with that type of aluminum insert as an accessory. What a great video - very well thought out and stepwise demonstration of how to mill up your own to fit just right.

[@DaveEbert]

your videos are outstanding keep it up. I for one cant stop watching your videos

[@NextLevelCarpentry]

Thanks for watching and commenting to let me know you're binging out on Next Level Carpentry!

[@ClintonCaraway-CNC]

The best saw I ever owned was a mid-90s Unisaw with the Unifence. I'd love to have a Unifence again. It was the most versatile tablesaw fence I have ever used.

[@NextLevelCarpentry]

Seems like all the upgrading 'they' have done to tablesaws since the mid 90's have actually been downgrades IMHO. Bet you could find a used replacement somewhere if you try...

[@michaelcantu1766]

I stuck around to the end I'm ready to make some first chance I get Thank you much, Great lesson

[@NextLevelCarpentry]

Thanks for watching (to the end X3) and commenting on this one... do you happen to have a brother named Chris? 🤔

[@michaelcantu1766]

@@NextLevelCarpentry Sorry just Three sister no brothers!

[@NextLevelCarpentry]

I ask because of your unique last name which is shared by a long time viewer/subscriber to the NLC Channel.

[@mikedtubey]

Love it! I will make one of these instead of making multiple plates. Thanks!!!

[@mmmdesignllc]

That was better than I thought it would be! Good job...again.

[@discerningx3375]

I am SO excited you decided to make this video!! Thank you! You are by far the most complete and comprehensive educator on YT. I learn as much or more from what you intend to teach by watching how you do your craft. Well done Matt.

[@NextLevelCarpentry]

I was hoping to hear back from some viewers who asked about the throat plate in previous videos... not sure if you're one of them but glad to share the process with you!

[@discerningx3375]

@@NextLevelCarpentry Hi Matt, it is Lee. You and I just discussed this over email a month or two ago. I had mentioned possibly using bamboo for the inserts. Great build and I watched the end of the end 🤣

[@NextLevelCarpentry]

@@discerningx3375 thanks for letting me know... I remember our conversation now that you mention it. Bamboo might be fun to use but plastic and MDF are probably the most stable options and less expensive albeit not quite as classy.. and thanks for watching to the end X3!

[@johntenhundfeld1529]

I certainly appreciate your videos. I have been watching since your very first one. You have kept up the clarity and level of humor throughout. Keep it up and thank you for doing it.

[@NextLevelCarpentry]

You're welcome John... hope recent NLC videos are easier to watch because of better editing/production? I do appreciate your sticking with the Channel as I feel editing has improved quite a bit from what I was able to do 5 years ago...

[@jwar2163]

I have a zero clearance throat plate with multiple inserts.Although I have a newer PCS Sawstop that throat plate made the dust collection even better and I can still use my riving knife. Wish this video was out then. Because that throat plate was not cheap from Infinity Tools. I will reference Your video Matt when I need to make replacement inserts. Thank you for sharing your knowledge.

[@danmac4132]

Outstanding, informative and clear instruction. Thank You!

[@richardvalli1058]

If making the initial clearance cut on the under side of the insert by hand is intimidating, try using an 8" blade from dado stack and raising the blade like you did for the final cut thru the insert with the fence holding everything down.

[@andrewbieger5004]

Good call. Less sketchy with your method. The dado blade is typically 1/8", so you cover the full kerf blades, as well.

[@trinitytoo]

Matt shows that at 59 minutes in, near the end.

[@richardvalli1058]

@@trinitytoo This was about using an 8" blade instead of a 10" one

[@trinitytoo]

@@richardvalli1058 Reread your original comment properly - missed your point about using a single blade, not the whole stack. Yes - a much better idea! And thanks for the poke because I'm much happier using your solution. TY

[@kkarllwt]

The right start to a video. what you made and why you made it. How it works. Then I can decide if I want to watch it.

[@hytekrednekbama4400]

I purchased one of these years ago, aluminum with oak insert. I love it. I forget the guys name I got mine from, but he is well known and a super good builder and finisher. I use mine for dadoes and slot and such. I use my Betterly zero clearance set as my everyday set/standard type blades set. The Betterly is even nicer but it is also more money. Both work great and will last forever.

[@hytekrednekbama4400]

Edit... Charles Neil is who I got mine from for a delta unisaw. Got it about 7 years ago or so. Sadly, Mr.Neil has passed away. He was a master of finishing for sure, and a superb woodworker, but most of all, he was a wonderful teacher.

[@NextLevelCarpentry]

Could you post a link to the throat plate you describe? Also one for the Betterly model? I think other viewers, myself included, would appreciate it along with the comments/perspective you've already posted here. Thanks. Best, Matt

[@greavous93]

we call that a "spring cut" in the machining world. Mostly when turning a part that needs to be dead nutz. I made my version of your throat plate about 25 years ago when they first came out. I wasnt going to spend the money but Id spend the time. I used some 1/4 inch plywood and had all sorts of trouble with the inserts swelling and shrinking over time and weather changes. I need to make a good one like yours now as Im a believer of zero kerf throat plates.

[@mightymorka]

Just love all your videos and can see all your skills on display, very inspiring for us newbies, Thanks!

[@NextLevelCarpentry]

Thanks for the Super Thanks "tip" mightymorka... it's much appreciated and you're quite welcome!

[@brianwalters6320]

I know this video may seem long, but I enjoyed all of the details. I am impressed with your skills and knowledge. Thanks for sharing.

[@NextLevelCarpentry]

Glad to hear you're good with long videos that are full of details Brian... much appreciated!

[@russkellogg8189]

Thanks!

[@NextLevelCarpentry]

Thanks for the Super Thanks Russ... much appreciated!! Hope you're able to make one of these for your saw if you're inclined to do so... Best, Matt

[@steveh7866]

Only wanted a quick sandwich and you made a 4 course meal! Thanks - there are always going to be things folks would do differently/more simply/cost effectively - but they didn't spend the time to make the vid

[@johnmclarnon5890]

Awesome design😊 After seeing your video, I have decided to try to make one for my Delta table saw ! Thank you for another very, very informative video.

[@NextLevelCarpentry]

You're welcome John... I get the impression quite a few others are making these too. Have fun with the build and enjoy working with it when you're done!

[@orrinkelso9295]

Excellent video. I am definitely going to make some of those for my saw. I also have a Delta Unisaw like yours. Except mine was made in the early 50's. I also do not have a splitter or riving knife. Never have. But my dad was a custom furniture maker and I grew up in the shop. The shop was on the Same property so we were in there all the time. My dad taught us how to use all of the tools properly. So knowing what you can and can't do with a table saw prevents accidents. If I had a splitter or riving knife I would use it but with this old saw, that is difficult to do.

[@NextLevelCarpentry]

I think you'll really like one of these for your saw if/when you get around to making one. It's a nice upgrade to even a decent OEM throat plate and, considering the age of your saw, should be a dramatic improvement. Have fun making and using it... and keep up your safe work practices!

[@geoffreykail9129]

One of the most useful videos ever. TY The last tidbid for first cut was good too.😁

[@aco319sig3]

Very detailed and exacting instructions. Thank you!

[@rontidd6551]

Oh. Thanks a lot, now I have to go make some of these.. :) As always, thank you.

[@88gogoyubari]

Top notch craftsmanship as well as videography. Most enjoyable. Thank you!

[@NextLevelCarpentry]

Thanks for sayin' Steve... this video was a long time coming and I'm glad to share it with the world of KZbin.

[@victoryak86]

I think this is a great idea. Was thinking of over sizing the pieces width wise first, cutting the dovetails to the size as he shows, then simply cutting all the pieces to width with proper offsets.

[@NextLevelCarpentry]

There's surely a number of different sequences to get the inserts to fit but I like the one shown in the video best because it's repeatable for making batches of inserts far into the future...

[@abe9mc]

I'm glad I stuck around for the end of the end of the end... I have the same insert setup for my table saw and the replacement inserts are impossible to find. I can make my own now; and saw how you have yours marked for different setups. That section at the very end was an epiphany. Thanks for opening my eyes. Great videos!

[@NextLevelCarpentry]

It's a great accessory to be sure! These are the first MDF inserts I've ever made and I'm really liking them because they don't grow/shrink with changes in humidity and become loose or tight accordingly. I hope you can find MDF that's actually a full 1/4" thick though because the stuff I have is too thin to work well in either aluminum throat plate I have.

[@tomholman2881]

terrific How-To video! Thank You I made one with HDPE too but to cut the first cut I installed a 7.5 in blade from my Skillsaw, Thanks again.

[@jimb9459]

Great solution to a common problem. Thank you.

[@N719SM]

Thank you for a great video! I look forward to making my own plates for an old Rigid table saw.