Machining Process of 2000KG Pulley with Old Scottish Lathe

[@williamcooper2368]

I can't even imagine. How much that piece must COST

[@USA-freedom]

Less than you may think. Ran a VTL for years. What you see here is simple machining on one of the easiest metals to work with cast iron. This part was probably made complete in under 24 hours. The casting to is a simple one to product also.

[@RodneyBrunton]

Think about the machine that's going on to 💰💰✌️🇺🇸

[@KnolltopFarms]

$99.95! Order now!

[@KnolltopFarms]

​@USA-freedom what's the difference between a VTL and a VBL?

[@USA-freedom]

@@KnolltopFarms They are very similar in many ways and the much larger of the two is actual called a vertical boring mill.

[@eddyb1596]

I worked Emerson Fisher Controls in college and got to tour the manufacturing floor where they had an eight foot tabletop lathe and was told about the time a part came loose and rocked the whole plant like an earthquake.

[@izalman]

Very nice old Webster & Bennet Vertical borer, very versatile bit of kit in skilled hands.

[@Wlad47kz]

Представляю каких размеров агрегат куда его установят.

[@peterfitzpatrick7032]

Should be fun getting all those belts tensioned properly, even with a matched set any slight deviation from the specs on the grooves will have wildly differing belt seating and subsequent tension variations from groove to groove.... 😲

[@ramonjimenez594]

Muy interesante su observación 👍

[@TheDiosdebaca]

Use bonded belts (I'm sure it's as special order as the pulley) and you're good to go. Just make sure the pulleys are square to each other, lol.

[@peterfitzpatrick7032]

@@TheDiosdebaca To a degree I agree with you, but if a couple of those machined grooves are a fraction wider than others, they wont be sharing the load equally is what I'm saying...a multi-veed bonded belt wont really solve that issue as much as mask its existence... as for your point of the pullies being parallel to each other when using bonded belts... well, HELL YEAH !! 🙄😂 😎👍☘️🍺

[@WhyNot-ez8gf]

When the pully is the flywheel

[@alanhenderson9092]

Haven’t done anything like that for more than 25 years now but I can still taste the metallic cast iron dust in the back of my throat watching this 😂

[@ironwill8596]

Vertical lathes are awesome

[@ruldali615]

В Пакистане советских станков почти не было. Это была британская зона.

[@AndresRodriguez-ym6zq]

Es una pieza para relog de mano.

[@user-zz1xg7eb9e]

😂😂😂😂😂😂😂 😂😂Elephant clock

[@user-su1oq4wb3r]

Стоп! Они же сделали детали за две установки,а второй раз зажимали за не обрабатываемую поверхность,там же биение 100%😮 В чём я не прав?

[@gurwantsingh5068]

Amazing, Hard Working People 👍👍👍👍👍

[@user-xz7xh2hq7b]

Изготовление шкива генератора ЛАДА ПРИОРЫ

[@FeederBrain]

Не путай, это обгонная муфта генератора!

[@user-xz7xh2hq7b]

@@FeederBrain на приору

[@user-wq4ik4gc9p]

Как с языка снял 😂только хотел что то подобное выдать в студию

[@bobrat]

You can't believe how loud this is. I worked at Harnisfager in the 70's and we cut the cast iron rollers for the overhead cranes.

[@landlifem5872]

But webster and Bennett are english, and it's a verticle borer, not a lathe...

[@joewoodchuck3824]

A distinction without a difference.

[@landlifem5872]

@@joewoodchuck3824 yeah right ....

[@joewoodchuck3824]

@@landlifem5872 Work piece rotating against a tool bit in both cases. One has a 90° axis difference from the other. Same function.

[@oh_crumpets]

Aren’t they from Coventry? I’ve seen many other videos and calling them Scottish too

[@markbeale7390]

Vertical lathe.

[@user-hn5je8nw5s]

Это карусельный станок!такие и в разы больше выпускал в СССР завод им. СЕДИНА в Краснодаре Нет СССР нет завода😢

[@DarkAngelOfWar1]

Карусельный станок подарен совку от Америки так как придуман был в Америке как и ЧПУ

[@_tot_ruslan_]

Есть завод, его сейчас под оборонку переделывают. И так же он мелкосерийное производство освоил. С китаем тяжело конкурировать. Цена! Но все восстанавливать стали)

[@viperz888]

This is a Webster & Bennet, made in Scotland 🏴󠁧󠁢󠁳󠁣󠁴󠁿

[@frankroy9423]

These guys never sease to amaize, they are the best.

[@damata4983]

ADMIRO MUITO QUEM FAZ ESSE TIPO DE TRABALHO.......TEM QUE SER PROFISSIONAL MESMO....

[@rodneypratt4324]

I have no idea what I just watched greetings from Texas

[@user-iu2sv9rg9e]

Complimenti eccellente lavoro 😊

[@user-fn5id5tt9j]

Loved running these machines, they are far superior to horizontal spindles for the type of work they do.

[@seanmolloy6188]

I can't imagine how many days and how many tips they went through. Dry cutting that thing.

[@ManuelLopez-ix6cn]

Great work guys 🎉🎉🎉🎉

[@themanthelegend7048]

Man super charger pulleys are getting crazy.

[@derspielographdsg7435]

As someone who did the same job for years, with the "small" difference that i did it in germany, my heart bleeds when i saw this.

[@bobrat]

And your ears

[@nivaldolopes5153]

Esses trabalhadores são muito bons

[@jesushuaman1226]

Hermoso metal mecánica ❤

[@ZinaVasilkova]

Когда не паришься о допусках и посадках!!!😂

[@imac786]

When you dont worry about the garbage coming out of your mouth😂

[@muten861]

Do they really let a two-tonn-high-precision pulley fell sideways😂😂😂

[@davidhamm5626]

It is harder than the ground, and on something that size a small nick would not matter.

[@muten861]

@@davidhamm5626 sorry, that isnt a sound argument. Whats about debree on the ground? Regular dust contains quartz cristals, which is close to diamant in its stiffness. What about hurting the structure of the object? Looks to me less impressive work, more as "primitive" or errorprone unterstanding of these people

[@Matthew_Removeafterwashing]

​@@muten861for the price they will get for making this pulley no one would care about minor damages and scratches

[@davidhamm5626]

@@muten861If the object was weak, it would have showed that when it was being machined, and it would have broken. It will be exposed to dust, all of the time when it is being used, so I do not see the issue there. Yes it is a "primitive country" , but they do get the work offered to them.If everything they made failed, you would not see the many videos, on you tube, you do not have to like what you see, some of us are fine with it

[@muten861]

@@Matthew_Removeafterwashing jyeah, that may be a legitimate arguement!

[@KSKwak-fz9qc]

It's a large v-belt pulley cast in grey cast iron.

[@geraldomagelacoelhomagela9183]

Maravilha

[@jahangirqaisar1199]

Pakistanis patriots at work

[@robinvalantra6839]

God bless you

[@HanhiEmo]

I first looked that its gonna be one damn big sparkplug

[@ghostoftheUchiha3250]

No lubrication?

[@markbeale7390]

Graphite in cast iron, no lubrication required.

[@danieldesouzadiassouzadias6226]

Usinagem super pezada com máquinas rudimentares todavia o serviço então 1000 parabéns

[@BigDrawls79]

Ya boy precisely measured with a stick and sidewalk chalk

[@cat-man5522]

What is it even used for ?

[@janstolk486]

now , that's a big pully !

[@victimovtalent6036]

for air compressor?

[@joewoodchuck3824]

Very impressive. Shouldn't there be a cutting fluid in use?

[@bhagasasi425]

not really hot

[@markbeale7390]

Not required for cast iron.

[@andreblanchard8315]

The only reason would be to cut down on the dust in the air. In return for a nasty black sludge.

[@sujalkanker]

Do not use headphones 😅 While watching video

[@theprinceofallsaiyans5830]

Just breathing in all them lovely metal flakes

[@1tinMan]

Hey wait.. I forgot to carry the 1.

[@wornoutallover]

And that's just for the alternator.😂

[@Blade___]

This maybe a big crane pulley for heavy duty machinery maybe

[@theGeniustechDHRUVGOEL]

It looks like it is a belt driven part good luck fitting those belts to proper tension and maintaining no precision in this gynormus part will eating up efficiency like crazy.

[@Kutuz66]

У этой стали есть марка?

[@bundyboy961]

That is a vertical borer.

[@doge3667]

Reminds me of a lego tire

[@joaoalves1944]

Top

[@psychiatry-is-eugenics]

Dust mask ?

[@stevelandsaw3132]

What steel toes? 😅

[@Dimetrij1]

Точность на уровне ...

[@sc1petrol]

Have someone asked himself, how in the heck an old Scottish lathe turned out to be in Pakistan?

[@user-rc6zf3tt8q]

✊🔥🔥🔥🤝

[@CheckOne2]

What’s that rated to🤣

[@andrescosta3678]

Que trabajo perfecto

[@outerthoughts30]

Whats your surface feed? 500? Lol.

[@PistoKTM]

Where is the lubrication/cooling? That tip must be red hot 😂

[@Gottenhimfella]

Cast iron does not require cutting oil because the excess graphite lubricates the cutting edge, and because it is relatively brittle there is not much heat generated in the process of shearing it.

[@PistoKTM]

@@Gottenhimfella ok...i was suspecting that but think that It would be Better with cutting oil!

[@Gottenhimfella]

@@PistoKTM The problem with any sort of fluid is that it turns cast iron dust into an abrasive slurry or paste which quickly rounds off the sharp corner of the cutting tool. Which is why it's always machined dry in shops which do a lot of cast iron work.

[@PistoKTM]

@@Gottenhimfella thanks for the explanation my friend

[@nandkumarchure1149]

This industry having only momedian workers

[@user-Uralsedoi]

Дак вот куда Уралмаш переехал!😮

[@javierrincon4963]

Como sea, yo veo que ese torno tiene un desperfecto y la piesa no se mantiene totalmente centrada

[@anton-ei5gg5sn6s]

Чугуннина.

[@vishalkohli13]

Inki tecnology bahut piche hai abhi bhi hamre jha is 1000 guna tez gupta hai motar yaar

[@audio323]

And no a single piece of safety equipment was seen

[@vk2ig]

Only married pieces of safety equipment were seen ...

[@Matthew_Removeafterwashing]

​@@vk2igalso not

[@jameshall6277]

Tolerance of plus or minus shiny

[@annasakuramoto61]

😊

[@user-yw4dj4xp2i]

С таким за мерами на глаз, точность сомнительная будет

[@Mickel-jb3mt]

I was taught that the tool wasn't working correctly if it made that high pitched note. But I'm certainly not an expert. More comments would be good.

[@garrettwilson3264]

Some tools squeal especially in operations like this. Hearing protection is key not for the noise but the high pitch squealing

[@imranchaudry858]

Great Pakistani workers

[@shahbazshafi6873]

Good 👍 iop

[@RuliTemo-ru1tb]

No logro discernir el motivo de estos vídeos, el personal no cuenta con la mínima seguridad laboral, ni calzado apropiado, ni gafas, vaya, ni siquiera guantes... Es deprimente en verdad y la empresa, ganando millones

[@OrlandoBurguette-om6gx]

Para que máquina será?

[@ozenbash2912]

Гарний шківок

[@ChiragKharote]

Titans of CNC would have made it with the profile grinding wheel. Such a waste of time😂😂😂😂😂

[@Matthew_Removeafterwashing]

they would make a 30 seconds video in which they would just touch this large cast iron slab and it would be edited with 45 fast cuts and some random "rock" music

[@t.k.5698]

😮

[@user-dt8us5pe8n]

А по итогу гайка М8 😅

[@crazydeathcar]

There's gotta be a more efficient method to transfer power than this absurd pulley

[@josefreitasoliveira4547]

Falta máscara

[@user-ne8vc2mx9m]

Peralstan alat berat ia

[@leonidsimenzov6946]

Шкиф на мотор стиральной машины😂

[@user-dv8hl6tm5t]

高手

[@audio323]

Not even closed toe show with all those cast iron chips ... oowwwwww. Iron slivers in your toes alllll day

[@mikes2381]

Man these guys must have the worst boogers and black lung butter. This is a place that should have masks. But I can tell this is also sadly a place that tends to not have the money or rules to have PPE which would save them money on healthcare and people and companies would earn more for longer wuth said PPE.

[@user-sf6pw7wk6m]

Шкивочек 😂

[@budennovsk26rus]

Он уже поржаветь успел пока точили

[@ZinaVasilkova]

Достаточно одной смены!!!

[@iluha9818]

Ручейковый шкивок.

[@user-vk2vu6vp4i]

Чугуний 😅

[@ro_oa]

ㅇㄱㅁㅇ

[@faizan_mevv]

Shiv ling

[@fehidalshaikh6111]

This work is not clean and not professionally

[@My-vlogs07]

Bichara garib Pakistan 🤣

[@reynolportillo595]

El acero es de muy mala calidad ni siquiera es de acero inoxidable esa pieza no durara ni un par de años

[@Venom-nk8nd]

🇵🇬,.,.

[@FlatBroke612]

Dirkha allah Mohamed jihad

[@user-lc4lv1nf6t]

С таким же лицом обороняли евреи свои границы

[@user-tl8bx6og5q]

Чявік ун

[@putoncabron]

Cave man ways of machining. CNC is the way to go!!!!