How to fix bike freewheel. Pedals turn, but bike doesn't move.

Hello cyclists!
In this video tutorial, we'll see how to fix bike freewheel. The pedals turn, but the bike doesn't move. This may be due to a broken freewheel. Remove the wheel from the bike. Remove the freewheel. Use the long arm to easily remove the freewheel. The freewheel loves to cook and will not uncoil. Watch this video to the end and you will learn all the nuances of bike repair and freewheel. Subscribe and like the channel. To facilitate the freewheeling, be sure to treat the cap with a special fluid. Disassemble the ratchet. Start turning the freewheel clockwise. We see rust and a lot of dirt inside. We disassemble the freewheel completely to clean it, wash it, degrease it, lubricate it and reassemble it. We use a magnet to quickly collect all the balls. We have the top row, now the bottom row. As you can see, the teeth are sealed, full of dirt. This prevents the freewheel from working properly. Clean the dirt off the freewheel. Why does the bike not move? The spring isn't working. The freewheel won't engage. Clean the inside of the freewheel. Lubricate the seats and install the spring. There should not be thick grease in these places, otherwise everything will repeat itself. Apply some liquid lubricant. This is how we serve the freewheel workshop. It is essential to clean the freewheel thoroughly before reassembly. Then apply the right lubricant. We start with a thick layer of grease where the balls fit. Service bicycle freewheel. For grease, the balls stick like glue. Balls inside the freewheel. This keeps the balls from scattering all over the shop. Do the same with the top row of balls. Lubricate the top cup. We put the balls to sleep. See how they do it in a workshop. Little trick. How to refill balls quickly and easily. Freewheel assembly. We turn the freewheel counterclockwise. Works perfectly, like new. For additional moisture protection, we lubricate the canyon. Put a ratchet on the wheel. Tighten the freewheel again. We use no special tools. Just a regular screw and a hammer. Like this secret). Be sure to subscribe to the channel Don't miss out on interesting releases. Putting the wheel on the bike. Testing the bike. Everything works! Thanks for watching! Rate videos you like. Ask questions in the comments.
#freewheel #bicycle #tutorial
00:00 Video tutorial on how to fix bike freewheel
00:17 Pedals turning, but bike not moving
00:36 Remove wheel from bike
01:01 removing the mf-tz500 freewheel
02:01 Disassembling the ratchet
03:30 removing dirt from the freewheel
03:48 why is the bike not moving?
04:13 bike freewheel inside
05:47 bike freewheel service tournament mf-tz500
06:04 balls inside freewheel shimano
06:52 assembly freewheel shimano mf-tz500
07:37 putting the ratchet on the wheel
08:14 Putting the wheel on the bike
08:26 Testing the bike
🆗🎥🚲
Write in the comments, what you would like me to do in the new video.
❓❔❓
Ask your questions in the comments
👇👇👇

[@NiceBikeService]

❤ If you liked this video, 🙏 share this video with your friends 📈 it will help the development of the channel! ❓ ask your questions

[@sanjayprackashsk6839]

What is that injection

[@alangastonsalvatierra6518]

Tuve exactamente el mismo inconveniente... Me mate la cabeza desarmando para ver que era... Lo logre y lo pude solucionar... Pero si tu video habría visto tu video antes (hace dos días atrás) me hubieras ayudado como no te imaginas 👍👍

[@NiceBikeService]

))) en 4 días este video cumplirá un año)))) tenemos que hacer una mejor búsqueda))))

[@Rev.RatsRides]

I recently took a gamble on a motorized bike that has this exact issue. Thanks for the fix!

[@villageboy3316]

Facing that problem with whirlwind c4. No spare part shop

[@atikulislamsopnil3885]

Suddenly, My Freewhell doesn't work, freewheel 1 pin Broked i install 1 Pin... Now Freewheel Have 1 Pin and Bike Properly Working... Thank You❤❤

[@ioioytbd19]

your video benefitted me

[@Muser-w40]

Muy buen video. Muchas gracias por compartirlo 🤜🤛

[@NiceBikeService]

¡gracias por tu comentario! Comparte este vídeo con tus amigos, ¡ayudará al desarrollo del canal! 📈😘

[@lahnaflore2621]

This video saved my life!!

[@NiceBikeService]

glad to be of service! thanks for your feedback 😘

[@joseortega9633]

Excelente 👌 , me sirvió muchísimo

[@NiceBikeService]

gracias por tu comentario 😘

[@mathbluz]

This hook tool made from spoke is amazing. 😃

[@NiceBikeService]

Thank you for your feedback

[@gonzalodiaz1676]

Hoy me paso esto, gracias a este video se lo que tiene mi bicicleta ahora

[@NiceBikeService]

gracias por tu comentario 😘

[@LD_FPS]

🇧🇷This was a problem I faced straight! and it's very popular here in Brazil

[@LD_FPS]

@@NiceBikeService Exactly 😁🇧🇷

[@dastrevasparaaluz]

O pior que maioria das bicicletarias assistência técnica não executam este tipo de serviço.

[@LD_FPS]

​@@dastrevasparaaluz verdade mano 😢

[@beniligadoemtudo1450]

Otimo trabalho amigo

[@ramonuser54321]

Serviço de qualidade 👏🏽👏🏽👏🏽👏🏽

[@dastrevasparaaluz]

Muito bem feito e explicado. Gracias

[@volodyagord3834]

Чудовий канал! Хай щастить! 😉Danke sehr.

[@nesatdeniz5318]

Gerçekten iyi iş çıkardınız ❤

[@Depoox]

Jakiego klucza używasz do klucza do wolnobiegu, to 21? I jak go zamocowałeś do rury?

[@pattskatoey3139]

After going through that effort fixing the freewheel you should have cleaned up the axle and wheel too.

[@anakrantauorg]

Terima kasih tutorialnya

[@vikramthakorvikramthakor6184]

Thank you so much❤❤❤❤ 👏👏👏🙏🙏👍👍👍

[@NiceBikeService]

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

[@basricokicli3992]

çok güzel sunum çok yararlı.Teşekkürler..

[@NiceBikeService]

Geri bildiriminiz için teşekkür ederiz!

[@tysonogoti7163]

I can now fix my bike myself thank you.

[@NiceBikeService]

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

[@tysonogoti7163]

Alright

[@belowzeronautilus2207]

Cassette is already closed, you can clearly see it on the teeth... new cassette costs 15€. It then also makes sense to clean the cone, grease and adjust the new one before remounting the cassette

[@Muser-w40]

Quizás 15€ en el país donde se realizó este arreglo sea mucho dinero. Pero sí concuerdo contigo que es una pena no haber limpiado el resto antes de volver a montarlo...pero de nuevo: habría que ver si el dueño solo podía pagar el servicio que se muestra aquí 🤷🏻‍♀️🤜🤛

[@chanrite1]

thank you

[@timbocando]

THANK YOU!

[@NiceBikeService]

thank you for your comment! Share this video with your friends, it will help the development of the channel! 📈😘

[@RCh1]

That's right. Did it many times...

[@carljeromeaquilos8725]

Man how do you fix a sprocker that has a grinding noise when i freewheel, I just cleaned it with wd40 then put some chain lube on the seems, but it still makes grinding noise as if it is dry

[@lasselyhne-hansen9338]

Thanks!

[@NiceBikeService]

Thank you for your comment! 😍 If you liked my videos ❤️, support the channel financially 💰🙏. Use the "Membership" / "Sponsor" function on KZbin ✊😘

[@maddax6372]

Excellent 👍

[@NiceBikeService]

❤️

[@11GDR]

Зачотна кочерга для зйому тріскачок 😃👍

[@massimouguzzoni8631]

Grazie.

[@roxfoot]

Brilliant.

[@KKoji]

After assembling the hammers, it is best to change their position. The wear on the part can cause different situations, so when you change it you will know if they open more. You should put grease inside the body, and be more generous with bearing grease. don't put it out. it is a good idea to remove a thin washer and lock the nut to remove play.

[@NiceBikeService]

thanks for the advice ! 😘

[@snakerstran9101]

DO NOT remove those thin washers willy-nilly. They set the spacing so the ring nut can be tightened securely without binding or rubbing on the moving parts. And the ring nut must be tightened very tightly as it tends to spin loose while riding and can loose the bearing balls.

[@KKoji]

@@snakerstran9101 to remove play.

[@peteturner8493]

What about the missing ball bearings and was high temperature bearing grease used, your 'A' typicall KZbin video leaving a lot to be desired sigh....!

[@technomindof6878]

The wheel still sounded very loud on the spin test,like bearings grinding into each other,maybe more grease maybe?

[@mattweabrigida7449]

perfect!

[@SqBike]

Kasetę bym czyścił tak starannie lecz wolnobieg już nie, lepiej nowy byłoby kupić, ake szanuje za pracę 👍

[@petmonkey4798]

⭐⭐⭐⭐⭐👍👍👍👍👍Thank You for this vidéo!

[@irfanaazher2050]

Thanks u for this 😢

[@NiceBikeService]

thank you for your comment!

[@lepwokeuplikethis1851]

Hey! I have a question, can we put a fixie cog on that hub? because there is a thread there, I thought I could attach a fixie cog

[@NiceBikeService]

Good afternoon, for such bushings there are freewheels with a thread for 1 star. Maybe the one like yours will work, but we haven't checked.

[@SemVontadeDeViver0]

Nice

[@aaronayala8325]

Muy bueno el video Ahora mi pregunta es, cuanto debería cobrar por este servicio?

[@NiceBikeService]

Aproximadamente un 50% más caro que el mantenimiento de los casquillos🐱

[@keliargabesar2039]

Please, how do you deal with the freewheel not being strong when climbing the sound of the trek track?

[@bachmtb7276]

Hướng dẫn như nầy là khó tiếp thu lắm, trước tiên bạn phải có chủ đề dành cho líp vặn, hoặc líp thả vì người xem họ chưa rành ạ.. còn như mình thì khỏi xem..

[@yus3907]

NICE

[@user-gx7pw4rs2k]

what are the tools you used for removal of the freewheel. Please mention all the tools. Many thanks

[@NiceBikeService]

that's what they're called, freewheeling tools.

[@euzebiuszkarpacki3810]

Czy tam nie brakowało jednej kulki? Pytam bi jak składałem taki stary wolnobieg to też mi brakowało kulki i teraz nie wiem czy tak ma być czy się zgubiła...

[@StacyKoinva]

I would to ask would this be possible for an Ambush bike? My rear tire is the same and I trying to fix it.

[@NiceBikeService]

If you have a freewheel, then everything is the same, you can fix it

[@StacyKoinva]

@@NiceBikeService I took it apart and didn't see any of the two square things where the spring would be and the magnets balls

[@anonymously241]

R you reusing old bearing?

[@rodrigomarzulo1874]

É bem assim essa mantagem de roda livre

[@NiceBikeService]

😉😺

[@li-on1]

What tool did you use to remove the "lockring"? I need one with 12 teeth and 30 mm diameter..

[@li-on1]

@@NiceBikeService Thanks for the answer but I meant the tool to disassemble the first cogs? The one thats cylindrical. A usual cassette removal tool is too small.

[@KINGTAPOUT_RELOADED]

Parktool FR-7 12 notch

[@li-on1]

@@KINGTAPOUT_RELOADED Thanks for the info. Unfortunately, this tool is only 23 mm in diameter and not 30 mm. Im searching for a 30 mm to actually "open" the freewheel. To do so, the outermost cogs need to be removed first.

[@fbevera]

What kind of grease was that being used in the syringe?

[@NiceBikeService]

calcium divinol grease

[@letspwa]

whats that grease?

[@angelocordovil]

Faltou limpar a corrente e a base onde a roda livre se enrosca no cubo junto aos raios, não ficou serviço completo. Ou seja faltou fazer limpeza completa no cubo

[@NiceBikeService]

obrigado pelo conselho! 😘

[@heiaheiaful]

Prijatno! Smazki tolko totšno kakih ta lutše postavit?

[@NiceBikeService]

Hvala za komentar. Ne nanašajte preveč maščobe in ne nanašajte goste maščobe pod zapahi, ker se bodo prijele. Za mazanje lahko uporabite polietilensko vrečko z odrezanim vogalnikom

[@heiaheiaful]

@@NiceBikeService Nu paren ti dajoš ;) Tolko tšeres google ponjal što govoriš. Ižvini što russkimi bukvimi ne mogu pisat, dolgo poidjot. Horošo, pod dvigušimi materjalam ne daju posla maslo, no što za struktura posla maslo na lager poidjot? Vrjatli silicon? Naverno hot kakova tsvet lagernoi zmas ?

[@gaspargaspar3462]

top notch

[@Pawankumar-tt5so]

Your video help full Aap ko meri taraf se dhanyvad ❤

[@NiceBikeService]

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

[@Lappillainen]

This happened once to my bike while I was cycling home and felt that "Ivgotta go" . It was a long walk home....

[@dranurag22]

general size of ball bearings needed in a freehub?

[@NiceBikeService]

Usually use balls with a diameter of 3 mm

[@user-dk6nt2od8b]

Ok👍👍👍 uzbekstan

[@NiceBikeService]

👋😸

[@user-ko8hw3do4r]

vc não e santo mas faz milagre kkkk muito top

[@NiceBikeService]

😽

[@junzaragozavalladores5592]

boss ask kulang saan po bike shop nyo

[@user-nn3ic1iy2k]

how to put the steering wheel and grease

[@PeaceDarusNi]

Доброго дня,можете підсказати яка трансмісія краща для велосипеда 18кил 21рама і 29 тіпа мтб, щоб проїхати мені хотя б 200 метрів то лиш з горкі на дорогах треба постійно крутити трансмісія напевно найдешевша стоїть,думаю перейти на касету,але такій апгрейд на новий велосипед виходить напевно 😅 є в мене якісь варіант? Велосипед norman pegas/pegasus

[@PeaceDarusNi]

@@NiceBikeService взагалі не хватае швидкості даже по прямі дорозі,десь 15км може і розганяю але такій темп виснажує 🤷😭

[@FerscMoses]

Ty ♥

[@NiceBikeService]

♥♥

[@robertmcfadyen9156]

I haven't encountered this for 20 years now .

[@burhanbakshi9982]

What is the cause of this problem? I have same issue with my cycle.

[@Abhishek__Parihar]

it is very hard to find a cycle repair shop in my city and only few of them repair gear cycle's and i am sure none of them will a repair gear cassette

[@NiceBikeService]

Anything can happen) if a person watches my video tutorial, they can definitely do it again.) Sometimes, it is necessary to repair one part so that you don't have to replace the whole drivetrain of a bicycle.

[@Abhishek__Parihar]

@@NiceBikeService yeah, you did great work

[@NiceBikeService]

thank you for your comment! Share this video with your friends, it will help the development of the channel! 📈😘

[@jco3665]

Bang maaf tanya untuk ukuran pelor nya berapa ya bang trima kasih

[@Ezen73]

what grease do you use

[@NiceBikeService]

grease - shimano! Share this video with your friends, it will help the development of the channel! 📈😘

[@user-qi2yw7qg4b]

What was the green stuff you use

[@codykorzenowski6888]

Lube, it’s not always green but they all do the same thing the lube I have is red

[@reverse_rain]

Невже лагодити її ( для замовника) дешевше аніж замінити?

[@user-wy3di8tg9s]

what nucleo is

[@LetsDiscoverMauritius]

How many bearings are there on top and bottom?

[@NiceBikeService]

There are different designs of freewheels, in this one there are 36 balls at the bottom, 30 at the top, 66 in total

[@irfanaazher2050]

I was also having the same issue

[@NiceBikeService]

glad to be of service! thanks for your feedback 😘

[@rudragurung8407]

What happens when then spring is broken? And alternative to DIY stuff!?

[@NiceBikeService]

Then it's a complete replacement

[@robertmcfadyen9156]

Wash everything in a degreaser canister to save time .

[@eduardosavala1140]

Si combine cuando aun tiene un 50% de vida si no es asi mejor cambiarlo por una nueva ✌️👊🏼

[@NiceBikeService]

Entonces habría tenido que cambiar además la cadena y las bielas

[@francoisaacfic]

En las bolas, por arriba lleva una aro de metal y después va la tapa

[@nagasumi-sempai6740]

Como se llama el líquido que hechas

[@NiceBikeService]

Si te refieres a la grasa, es grasa de calcio divinol

[@viktorsvetlov80]

What kind of lubricant do you use(green) ?!

[@CTZN1]

yeah i wonder that too

[@x21gokartracing]

I have done maintenance to front and rear wheels, crank, front neck, to eliminate wash out of the grease I have always used marine grease with no issues.

[@Lukas-gd9we]

Is there no need for grease or oil on the inner theeth of the freehub? Becaue the pawls are constantly moving over them?

[@R3FL3X84]

is that a shumano tz freewheel ? is sounds so quiet :)

[@NiceBikeService]

Yes, it's a freewheeling shimano, but it's unknown which series😺

[@coronelpliskin3648]

como se llaman y que medidas son las bollitas que se ven el en minuto 3:13?

[@NiceBikeService]

tiene el nombre. Libre albedrío. No puedo decirte las dimensiones.

[@yokanshree4621]

Is that a steel pipe

[@jaydenrichards8815]

My pawls aren't bouncing up to hook in the teeth , I cleaned it and everything but idk why its not bouncy anymore , any advice ?

[@larrydaniels8976]

Probably put the pawls in backwards.

[@dragonart5687]

Ball measurement please 🙏

[@user-nn3ic1iy2k]

how to flip a bushing

[@BZepline]

What is the size of the steel ball

[@NiceBikeService]

Usually 3mm

[@casel4154]

В мене сталась така сама поламка, довелось новий купувати

[@user-nn3ic1iy2k]

Как смазать руль на велосипеде супер відео увас

[@jarosawzalewski4721]

Człowieku wolnobiegu się nie naprawia..Wolnobieg się wymienia wraz z łańcuchem! Pozdro Amator.

[@adredy]

jak to sie nie naprawia , domow tez nie powinno sie naprawiac stawia sie nowe :D

[@potato2531]

What if i dont gave that tool to remove the casette?

[@NiceBikeService]

It is impossible to remove the cassette without this tool. Better buy it, it is not expensive and is sold in any bike shop or can be ordered online

[@sebastiansalinas5244]

Que tipo de grasa se usa?

[@NiceBikeService]

Utilizamos grasa cálcica espesa, disponible en muchos fabricantes.

[@duniageme-gm7us]

Kak kriwil buat sepedah aviator ukuran 20 sama kah

[@NiceBikeService]

👍

[@marianbalaure9414]

ciocanul este interesant 🙂

[@ahmadfouadassaf6856]

جميل gut

[@NiceBikeService]

شكرًا لك على تعليقك! 😍

[@ebilqasimov]

Allah razı olsun senden

[@bigwheelsturning]

Now do the BB and Head Set.

[@edisonmurillo1576]

Es mejor cambiar todo el sistema

[@milindasenarath]

my freewheel completely gone silent after a service. now i dont hear any click. is that a problem ? bike rides fine

[@milindasenarath]

@@NiceBikeService i live in Srilanka . in here temperature is always around 25-33c. no winter.

[@deniwidiana6370]

Ball bearing size? Please

[@NiceBikeService]

3.17 mm or 1/8 inch

[@RobertoCarlossasigagaitan]

Yo he desarmado y engrasado ese piñón de roska a los Q no le entiendo es a los de casette

[@NiceBikeService]

sucede.