Nissan Frontier Ignition Coil Fix CODE P0300, P0301-6

[@noahmarcus7081]

It takes two minutes to change plugs and coils on the driver side but the passenger side is a completely different story luckily my misfire is in cylinder 2 this time tho

[@DAN-ib5kj]

Good gob .I got a 2007 nissan fronter .found out my 5 spark plugs misfiring im not mech so hope yu help me thought this

[@martyrafter5588]

You got lucky it was that side of the motor because the passenger side sucks to get too. I replaced all the spark plugs yesterday and I still have the same issue. I guess its time for coils. I dont know which coil it is and I don't have time to unbolt the intake and rebolt it back on three times to figure it out. I guess I'm buying 6 coils.

[@DwayneKenDoIt]

By now I've done it a few times and the intake is lickety split to take off for me lol

[@martyrafter5588]

@@DwayneKenDoIt do you have a link for the one you bought.

[@DwayneKenDoIt]

@@martyrafter5588 www.amazon.com/Hitachi-IGC0006-Ignition-Coil/dp/B004A0RAE0

[@909fresh]

Man thanks for this. Best video on the issue 💯

[@rafiktunangler6190]

Thanks for the video, i have some symptoms like yours, at idle the rpm drop and bounce back, hesitation when accelerating, car shaking when at idle...but no check engine light. How to diagnose and determine the faulty one?

[@luisvaldez2941]

I have the same issues for months not. Check engine finally came on today

[@Chris.Lewis1456]

I have p0300 put new plugs, bew coils, still same thing. Also changed cats oit and its still having that code. Runs good still as long as the engine light is on. If i reset it it runs like crap. And it has a bad exhaust smell like it's dumping fuel. Has new injectors also. And a new fuel pump. And timing chain and guides im stumped now.

[@DwayneKenDoIt]

Any noises? On this one I eventually sucked cat debris into the motor and bent connecting rods and ruined the motor. Replaced it with one from a wrecker

[@Chris.Lewis1456]

​@@DwayneKenDoItno noise at all and truck runs strong.

[@mb1636]

Where did you get your made in japan ignition coil. Please add link if you can.

[@DwayneKenDoIt]

Hitachi IGC0006 Ignition Coil www.amazon.ca/dp/B004A0RAE0/ref=cm_sw_r_apan_glt_i_HBHCEM0QDH0W3TBBZPJP?_encoding=UTF8&psc=1

[@ricardocarrera5252]

I have a P0300 new spark plugs and new coils, wont give me a specific cilinder, just reads misfire? Also removed catalytic converter for the driver side and cleand it. Any suggestions?

[@DwayneKenDoIt]

Still gives p0300 after changing that stuff and clearing codes? I'll have to think. Also check the forums

[@DwayneKenDoIt]

Any other codes?

[@ricardocarrera5252]

@@DwayneKenDoIt no that's all.

[@kyarakll4os7]

What does a misfire feel like? My 2016 frontier sometimes vibrates when sitting in idle or at a red light/ drops in RPMs to about 550 then bounces back up. Sometimes when I accelerate it will hesitate or tiny jerk. But once the truck gets going it runs smooth.

[@DwayneKenDoIt]

In my experience it was usually, if not always under load and you can feel the vehicle jerk

[@rafiktunangler6190]

Hi, any updates on your problem cause? I have the same symptoms. What did you do?

[@kyarakll4os7]

@@rafiktunangler6190 I ended up taking it to Nissan. They had to relearn the throttle position sensor/throttle body, raising the RPM to about 750. It runs great now but I did notice my MPG drop from 16 to 15. Not huge but every little bit counts lol.

[@rafiktunangler6190]

@@kyarakll4os7 i did the relearn by myself, but nothing changed the rpm still drops and bounce back at idle...i suspect a coil but no check engine light came on so far so its hard to locate the faulty one

[@bda2696]

Wow stick shift??

[@DwayneKenDoIt]

Yes

[@6468791]

Can you use different brands of coils?

[@DwayneKenDoIt]

Yea I have used a couple different aftermarket brands

[@axidhaus]

Hitachi is best

[@adrainromo950]

How you know is fail number

[@DwayneKenDoIt]

P0301 means cylinder 1, p0306 means cylinder 6

[@MyRcGoSlow]

@@DwayneKenDoIt what about p0300 lol I got a 02 frontier v6

[@DwayneKenDoIt]

@@MyRcGoSlow that'll mean cylinder 2. Take that coil out and swap it with another and see if the code goes to the new cylinder

[@MyRcGoSlow]

@@DwayneKenDoIt can u check my vid I posted on my channel that’s what my truck is doing plus I have the p0300 code

[@karelia8207]

Is this applicable for Pathfinder?

[@DwayneKenDoIt]

Anything with vq40de motor

[@fueledbykush]

Is it dangerous to drive with bad ignition coil

[@DwayneKenDoIt]

If it's a few days and you take it easy I would think no

[@wsmaga]

It’s not dangerous but you still ruin your cats and then after there’s a whole bunch of problems. Also the cats for these is over 3 thousand dollars.

[@maleekgreene5335]

How did it shifts?

[@bda2696]

Looks like it's a manual

[@999benhonda]

Pray you don't get a P0301...that one is a bitch to get to. It can be done without taking off the intake plenum, but requires a fair bit of cursing to make it happen.

[@DwayneKenDoIt]

Lol oh don't you worry, I've had it since this video.... Pretty quick at taking the intake off already

[@cswhuntingfishing8068]

I gotta do p0301 lol

[@DwayneKenDoIt]

@@cswhuntingfishing8068 pain in the ass haha

[@gavinsingh4450]

@@DwayneKenDoIt Don't take the intake off. Loosen the coil and rotate it 180° and pull straight up!