Nissan P0507 Idle Relearn Procedure

[@hjkjccdggjhvb]

thank you ,your video help me. I have a 2006 pathfinder. All other videos on here didn't explain well enough. You were right about the check engine light. In order for it to work, the check engine light has to flash differently once u hold the gas pedal. Everything has to be concise and if u don't see the check engine light flashing differently then you have to redo it over and over until u see it.. once again, for those who's trying to do this , look for the different check engine flash ... if u don't see it then u have to redo it... it's not going to work, This is simple and if u follow exactly how he shows , it will work... 👍 god bless

[@robertmaher2842]

I just completed a tune up, valve cover replacement, engine bay cleaning, and a throttle body cleaning on my 2005 Frontier V6. It ran great, except I was getting this P0507 code and a high idle. I found this video through Google, and tried it. Worked 1st time. I very much appreciate you putting this out there!

[@AlwaysArctic]

Almost gave up , got it on my 8th try, thanks, waiting the 3 seconds before the 5 presses helped a lot

[@jaredmeade3246]

I think it worked. Thanks sooo much!!! 4 years later still helping people!!

[@skipwondah33]

Great video. Worked for me on 2nd try using these exact instructions. Alot of the videos and instructions found online, were not working for me. These were perfect. Thanks again.

[@mayurelacachucha]

I tried several times and still stays the same . Not sure what to do anymore

[@davidshipley8710]

Thank you. After multiple attempts and it not working I found your video. 3 seconds made the difference.

[@WITCHBANE]

Thank you so much! Tons of videos and yours was the most easily understood to follow! Years later, and your lesson helped me finally fix my 2005 Nissan Pathfinder. 🙏👍

[@coltonm.1487]

Thank you for this comment. I did t know if my 2006 was too old or not

[@WITCHBANE]

@@coltonm.1487 Nope, it was exactly what I needed to get the job done 👍

[@hjkjccdggjhvb]

how many test did he perform on here , he didn't explain it. Seems like he did the 3 second off , ten seconds on with the foot pedal ... if i'm guessing it

[@mrfordman9999]

Thank you so much! I did the same cleaning and had the same high idle issue. That oil light made my heart skip a beat 🤣

[@JohnMcbride-t3h]

I want to thank you for your video, it was extremely helpful when replacing my thermostat on my 2018 Frontier today. It took a minute to get the gasket right, runs 100% now

[@oscarfaulkenberry1582]

I bought truck used - my wife said it sounded like a locomotive when i started it. Used this procedure and it idles properly after one try - THANKS

[@kingpapa4672]

After cleaning my 2005 Nissan Xterra, it idled to high. It took 5 or 6 tries and this worked. Keep trying if it does not work at first and make sure you have everything set correctly. Very valuable information. Thank you

[@juliomartinez-mw7ml]

This helped me a lot so I’ll tell what you probably already know the oil pressure sensor is out on this truck

[@JLondon951]

Thank you so much my friend! Worked perfectly. I got a bit confused with the delay. You just have to repeat the 10 seconds. Once again thank you!

[@naserhwas2300]

Thank u sir i am from Libya no dealer in my country after many time I try u r way finaly it’s work for my Nissan Pathfinder 2007. Thank you so much sir

[@neilyakuza6595]

What a pain in the ass. I have to do this to my 2010 Xterra. Thank you for the video, so much easier to see the procedure being done visually.

[@11mantovani]

It works! Took me five times and I think been sharp with the 2 seconds made the difference. Don’t give up, it works! Thank you!

[@recklessnova74]

Thanks! Just installed a new ecm and idle was high along with the code. All fixed up.

[@Lucky512]

Thank you for posting this video it really helped me with my 2007 frontier.

[@ronaldoreyes2039]

Thank you so much worked properly after trying twice on a hot engine

[@leroyrosario6898]

I did all of this and check engine light is still on did everything lots of times

[@miguelcintron6595]

Thx a lot after 10 try finally made it 💪🏆🏆🏆🏆

[@ulf-dieterkoepp7865]

Wow - you meant 10 tries then you got through?

[@tylerharless4048]

Works great took two tries but fixed my titan

[@Aila_h]

Thank you so so much for this video!!! I was able to fix mine by the fifth try so definitely don’t give up after the first try or second try. Be patient and follow the steps as he says.

[@johnhuntington5078]

Works as advertised! Thanks for the video.

[@mannysegunda1]

Great video. Good to know. It worked at the 3rd time in my 05 path

[@jamesgoode8115]

I have had a p0507 light on my 6 speed manual 2007 Nissan Frontier for about 3 weeks after cleaning throttle body and air filter. I had attempted the idle relearn procedure like 30 times with no luck. Don’t know if it was a fluke but on the time it fixed it I accidentally kept the gas pedal fully depressed while starting it. I held it for a second or two and it wouldn’t start I released the gas pedal and it started and idled down to 600rpm. Don’t know if this was a fluke but it worked for me 🤷🏻‍♂️👍🤘🙏.

[@enriquebauza749]

Great job brother. I have a 2006 pathfinder. Its probably the same.did you cleaned the trottle plate??? Hey buddy am slight deaf cant hear you clearly.can you please write the steps for me i would highly appreciate it. God bless🙏👍👍👍👍

[@donsonthewise]

worked on my 2005 nissan armada, thank you.

[@FERNANDOFRANCHI]

Hi Auto Resource. I just watched your video on how to restore the idle speed on a Nissan Frontier. It was of great help. Thank you. Perhaps you can help me with another problem I caused to my daughter’s truck, a Nissan Frontier 2003. I replaced the spark plugs but I forgot to disconnect the battery causing a problem to the automatic transmission. This is the problem: When in “DRIVE”, the truck takes off normally in first gear. Then when the transmission should shift to 2nd gear it goes to 2nd, 3rd and 4th in a very rapid sequence making a sleeping sound. What I have been doing to drive the truck is placing the selector lever in 2. Then the truck takes off in 1st gear and at the right time shifts to 2nd.(as it should do). After I reach the speed of 40 MPH I move the lever to "D" and the transmission will shift to 3rd and 4th quickly but because I already have an inicial decent speed of 40 MPH the problem is tolerable. I think the computer part for the transmission got messed up when I didn't disconnect the battery. Is there a procedure you can share with me on how to restore the automatic transmission to normal? I will appreciate very much your advise on this particular problem. Thank you.

[@nickpiludu2564]

Thanks for the video.

[@OHNOKite]

Worked! Thanks for the video friend!!

[@Krma-3]

Great just fixed my xterra by doing this sitting here watching fixed it in 3 min!

[@victor26gzlz]

Thank you i think it worked for me too, i will drive my truck tomorrow and see how it goes, thank you 👍🏼

[@caputodentallaboratory3117]

Why is oil light on. ? Awesome video thanks

[@oswaldoresendiz3313]

Hello, how many revolutions is an ideal idle? in this truck model, thank you

[@bgminton001]

Does this same procedure work for 98 Nissan Frontier 2.4L or is there a different procedure? I’ve tried this procedure multiple times with no luck

[@giuliom8520]

Great video! It worked after first try. I just followed your lead.

[@tejano2828]

I have a question. So....what if your xterra revs up to about 1200 rpms when you first start it but it then goes to about 550 on it's own in like 4 minutes is this normal?

[@blawblawblawblaw2891]

Yes very common with 4.0L

[@afrasiabkhan3706]

Thank u very much . U save the day. Working perfectly

[@lloyde73]

Hi sir, what is the brand name of your scan tool? Thank you

[@sekekamawow5386]

Just bought brand new 2019 Frontier and my idle is exactly where this is at. Between 500 and 750 so I would say it idles at 625.

[@eclectic3618]

Mine is the same low 600s, slight shutter at a red light at times, dealer says its normal

[@joseurtiz9598]

but your oil ligth keeps on did you check that later on the video?

[@twinskata86]

Will this also work for the 2.5l 4cylinder?

[@exoticprodetail]

Hi, I own a Nissan Pathfinder 2005 186.000 miles, recently check engine turns on, the scanner shows this code P0744, could you give some advise? please and thank you

[@truenorthmuskoka9077]

I cleaned my throttle body today and after putting it back on the idle was around 2000rpms. After about a minute the rpms dropped back to normal on its own and no codes. I guess it taught itself.

[@royquesada5295]

Why take the key out?

[@dftrain]

this worked great thanks!

[@qwertylowbubble]

What is normal idle speed for this vehicle?

[@hinklej2]

My check engine light doesn't work. How can I do this? Thanks

[@davidcotter4556]

Thank you sir, absolutely awesome Thankyou.😊

[@dfields9511]

Great video I have 2001 maxima I got p0505 Idle high at idle. I found air leak in intake hose from air box to throttle body. Got new hose and installed it cleared the code and it hasn’t come back. If something strange comes up again I think I will need to do this Throttle body was recently removed and reinstalled and intake gaskets replaced. Do you think this relearn procedure will help. My son normally drives that car and has stated that it gets a strange idle after a while say it’s in park and idles for like 5 minutes.

[@jacecherepak9408]

The check engine light on my 04 didn't stop flashing but beeped 3 times. Disappeared once I turned it off

[@zariarichardson3219]

How many to lock off and on again

[@parkersmith988]

Thank you so much! My baby is running super smooth again thanks to you. Very much appreciated my dude.

[@j1mmyv707]

Worked for me thank you.

[@josephcortez3143]

Took like 10 times as another comment said lol. It worked finally. You have to do it perfectly but it works. Woohoo

[@nurulabdul1566]

Thank you so much sir,my nissan frontier 2006 has the same problem, start engine rpm shows 1.5,,, followed your method SUCCESS,, thanks...

[@hankw999]

Thank you very much, after 5 tries I got it. Timing is critical or it will not work.

[@DarkLink66]

I can't get this to work, what am I doing wrong 😢

[@arrivendrive6831]

I had a stuck throttle and cleaned the throttle body. Turn the car on but the idle was 1100rpm. I did the relearn and now it floats up and down from 1200 to about 1600rpm. I am not sure what to do next. If anyone can help me please comment.

[@77FINNBEAR]

What’s good idle rpm?

[@raymondmarquez1347]

Thanks for the video... it worked!!!!!!!!!!!

[@surfstarcc1]

It's works!!! 👍

[@nicknock4201]

It did not work for me I tried and tried I saw that your check engine light was still on and then you cleared the code with your scanner

[@rafaelrioszepeda]

Yes yes working

[@leroyrosario6898]

I did all this and the check engine light still on

[@ReinerArrieta]

Aslo también en español saludos

[@kennethdarcy6606]

Great!!

[@haonski9231]

I have done this it worked but then the next day it is high idling again.

[@bfitnessjoe]

The procedure he spoke was correct. However his demonstration was visually incorrect. The “service engine soon” light did not flash as described. It remained solid and as a matter of fact his check engine light remained on after he started the vehicle. Do not use as a visual aid. Just listen to the video.

[@Steve-wf1gu]

Save me. Thank you

[@TSniper79]

This workee for me

[@nicknock4201]

This does not work and everyone saying that it did work I don't buy it maybe it did for some of you if you installed a new throttle body after cleaning my throttle body and trying this it did not work over and over I took it to mechanic of mine who had a $10,000 scanner tool and he hit the idle relearn button it drops from 1000 RPM down to 550 and 600-word should have been so do not clean your throttle body unless you want to take it somewhere and have them do it with the right kind of scanner to Snap-on $5,000 won't work you need a Maximus $10,000 scanner now for some of those that it did work I couldn't be happier for you because there is nothing better in the world been watching those RPMs go down to where they should be but if you watch most of these videos they will say well it didn't work for me hopefully it works for you they are only going by what Nissan procedures are in that is only for certain installments or repairs I don't refer anyone to work on their own stuff on a Nissan it unless you don't know what you're doing because these Japanese they are smart as s*** and they made sure of that by complicating everything so I'm hoping everyone really looks into things before they start doing stuff

[@cocomikes]

;)