Nissan Timing Chain Noise Problem

Nissan 3.5 with a noisy timing chain. Broken tensioner guide causing the problem.

[@mcleanb981]

Finally a quality video that actually describes how to fix something on my Nissan. Thank you, even if my noise isnt from my timing chain i found this useful and interesting.

[@metoon3092]

I own 3 Nissan Maxima's. At 178k,251k and 194k, Maintenance is key.I bought the one with 251k, replaced the Chain,gears etc., due to LACK OF OWNER MAINTENANCE. This is the ONLY thing you must do. These are INCREDIBLE Engines, just absolute Lousy owners. I also own a Acura TL, Good car, just a daily driver.

[@deasttn]

What is good maintenance on these engines? Just regular oil changes? (3k-5k)

[@YeetxBoi]

@@deasttn look online for the owners manual if you don't have one but it should list owner maintenance throughout 0-200,000 miles

[@rokitman5753]

He had left over bolts meaning he is a better engineer than the engineers themselves lol

[@Maximaniac72]

My timing chain on my '02 Maxima made a louder than usual rattling noise on startup this morning. It's always made a racket when it's first started in the morning, but today was louder. I hope this "fun" job is not in my future!

[@maximaniac7231]

Well, 2 years later and the engine and chain are still doing just fine. I did recently replace the valve cover gaskets myself and the area under the valve covers look like a new car at 165k miles. I really do think the only VQ's that have timing chain issues are because of people stretching out the oil changes too far. I've always changed mine at 5k miles, but my car burns a quart every 1000 miles so even after 5k the oil has been refreshed pretty well. If it didn't burn oil I'd go with 3,500 mile OCI's on this car on dino oil or 5k OCI's on synthetic.

[@thepalehorse4829]

So you had this noise and never got it taken in to get changed out?

[@maximaniac7231]

Maximaniac72 Never made the noise after that so I forgot about it. Car has 165k on it now and still runs like a top. It's never even had a CEL!

[@thepalehorse4829]

After what? What did you replace on it?

[@maximaniac7231]

John Ortiz Nothing.

[@duranortiz6261]

Is it possible to change out the primary tensioner through the access parts without removing the the entire timing chain cover?

[@jackfletcher5314]

Duran Ortiz yes

[@mcnobody1012]

My 02' Nissan Altima 3.5L SE seems to be making the same rattle. This is a great video,though I do wish you'd shown the procedure of taking that all apart & getting inside the engine as you had. Seems that is the most difficult part & I want to be sure, of what I need to perform it & procedure.

[@christiangriffith225]

There's actually a video on that. There are 3 parts.

[@twoeightythreez]

Yeah they changed the oil every 4000 miles, they probably didn't mention that they idled the engine for hours a day. I change the oil in my car every 10-12k miles and there is zero sludge. The difference is my commute is 40 miles one way and i dont sit and idle. I dont use drive throughs.

[@wwccauto]

This vehicle is not mine, the owner swears they change the oil every 4 or 5 k miles which should be fine but who knows what kind of oil they are using. The sludge buildup in this motor is extreme. Joseph Moran: if it is just making noise at start up it could just be the tensioner, but this engine only made the noise at start up for the first little bit before it got much worse. Here is the video showing some of the sludge buildup found in this motor. Engine Sludge

[@brianphillips5929]

so, you say it's a time consuming job. How long did it take you to complete?

[@chefboiii]

wwccauto Mine did not have that much sludge. Its likely they used the wrong oil because a nissan is very specific on what kind of oil to use. On top of that makes me wonder if they had any cooling system issues because poor performing cooling systems cause more sludge to form.

[@mrjoeyb]

+Stephanie H I've bin a Nissan mechanic 12 years, that era 3.5 and 4.0 engines all do it sooner or later. It's a design flaw. I've done many!

[@Abeltin89]

mrjoeyb how long does it usually take to clean up and fix?

[@bobl78]

yes, people say a lot of things when it comes to oil changes.. they always say " i had it done recently"... when you ask 5x then they admit that the last recently was 2 or 3 years ago... bad/wrong oil and too little oil changes play a big role when it comes to chain or tensioner issues...chains need clean and good oil and they`re also quite hard on the oil, too (shearing)

[@MikeMiller-kg8vh]

In your opinion, is it absolutely necessary to remove the upper oil pan. I've seen other videos on this job, and there is no mention of removing it. I know the Nissan shop manual states to remove it, but I'm hoping to bypass that step. My concern is the seal at the bottom of the timing chain cover since the upper oil pan would be already in place. I plan to do a dry fit to see how it will go.

[@wwccauto]

I removed the upper oil pan because it was leaking from the gasket on the transmission side. With the upper pan out it is easier to assure that the lower part of the timing chain cover will seal when you put it back. However, you don't need to remove it if you don't want too, and you can put the cover back on and have things seal up nicely.

[@dimitarkrastev1933]

How long it can run in this condition?

[@melloyellogsxr]

What did you do with all the extra bolts you had leftover when you put it back together?

[@danielebrparish4271]

Sell them on ebay. LOL

[@MikeyNDa513]

@@danielebrparish4271 🤣🤣🤣😂😂🤷‍♂🤷‍♂🤷‍♂

[@killabee623]

@@danielebrparish4271 LOL!!!!

[@zeus-io3hn]

if engine oil is changed every 5kto8k miles. this issue will not happen. dirty engine will sludge up the tension componants.

[@colty7764]

"hot spots" in the engine from carbon buildup can cause sludge (due to oil breakdown from excessive heat) .. so keep engine clean with gasoline additives like Chevron Techron, etc).

[@danielebrparish4271]

No, it's a defective design. The replacement parts are corrected for this defect.

[@johnchafin3817]

Did you have to remove the AC compressor and drain the freon?

[@Aegis359]

Great video. my '02 Sentra is doing this right now. Was the tensioner the only part you had to replace or was the chain and other things replaced aswell? thanks for the video

[@wwccauto]

If you are digging that deep into the engine everything ought to be replaced. Wear and tear on the sprockets and chain guides is easy to see, the chain itself can be a bit more difficult to assess. Best to just do it all, especially on a Sentra where all of these parts are fairly cheap. Replace the hydraulic tensioner as well.

[@mikeinfinitiify]

Do not use additives and make sure you change the oil every 5k kms not 5k miles use catrol mobil ,shell you need to replace the timing chains in can break anytime and will certainly breaks your valves and cylinder head

[@Travelingcarguy1]

I have a 2004 Nissan Quest with 134k miles and I have never had this timing chain problem. Do you think I may have this problem in future? At what mileage does this problem occurs of these vans?

[@melocitomelopongo2177]

Mine is 2005 and it just started at 110 k miles. I started hearing "coffee grinder" kind of noise coming from the passenger side of the engine.

[@thechaindude1320]

@@melocitomelopongo2177 my '08 started doing it around 117k. but we made the mistake of not allowing it to warm up before driving it

[@fireblade639]

HEY , MY TENSIONERS WERE CHANGED TWICE NOW, EVERY TIME THE COLD START UP SLACK SOUND FROM THE CHAIN GOES AWAY LIKE FOR 4 DAYS AND COME BACK, THE FIRST TENSIONERS THAT WERE CHANGED HAVE VERY LITTLE MARKS OF THE TIMING CHAIN, WHAT ELSE COULD IT BE,??? I HAVE A PERFECTLY CLEAN AND HEALTHY ENGINE AND CLEAN OIL, BUT THE SOUND DRIVES ME NUTS. COULD THE PHASER BE MAKING THE SOUND AT START UP???

[@malcolmlewis5102]

fireblade639 My 2002 Nissan Maxima was making this noise. I replaced the front left catalytic converter in which the clicking noise on the left side stopped. There's still a clicking on the right side of the car so I plan on replacing the timing chain to see if that addresses the noise. The Nissan service department alleges that both of my cats were performing at an inefficient level. When I got the repairs done for the cat, my mechanic (including a second opinion) confirmed that only one cat came up on the diagnostic code. I'm hoping that reolacimg the timing chain will resolve the clicking noise however; I may not be totally convinced that the radiator side doesn't need to be replaced as well. Just providing you with something to consider.

[@_DGOTGAME_]

Where are you located? If in Las Vegas area reach out I’m having this problem right now!! Help plz!!

[@AnunnakiThe1]

to those who complain about their vehicles:- people are too stupid today than they where 30 years ago , I am not a Mechanic but I sure know as you do too; you need air , food and water in order to stay alive ! so does your vehicle you rely on . it needs its oil change every 3000 miles or every 3 months , water ( antifreeze ) checked weekly with other fluids , and its tune up every year give or take . and other necessary parts such as brakes , tires , fuses , relays e.t.c . a big example is my girlfriend's niece drove her brand new Nissan Altima for 2 years and never changed its oil , and she wondered what the fuck went wrong with it ! as I showed her stupid ass the blown up head gasket . and a factory printed date on the oil filter 2 years prior that was never changed and the oil was so fucked ? it actually crystallized from burning dead. and she replied : oh , I didn't know that I had to change the oil . all the blessings you have and you complain about your vehicles been crappy ? I say :- you don't even deserve a fucking drivers license to begin with .

[@iwasborndogiwasborndog9721]

my engine is YD25 (frame d22) and a had a similar noise on the road yesterday which stopped after 20min , what was that noise?

[@rhondahill2241]

How will I know if I have a timing chain or timing belt for 2006 Nissan Sentra? I lifted the hood and saw a timing belt but not a chain. When I called to price an AC belt and timing belt, the guy said you should have a chain, not belt. I clearly hear the noise of the belt and I felt it and it feels like it's warn and cracking. Any suggestions/advice? Thanks👍🏼

[@FA-sr6lx]

Rhonda Hill Try Google

[@imnota]

The chain is hidden and the belt you see is probably for the ac,power steering,and all that shit...

[@jerrellhaynes4703]

Rhonda Hill your timing chain incsed in a metal cover& is lubercated with oil,if you don’t know that then you better not try changing it,it’s a lot of work& I recommend you buy a manuel& read it first!good luck if you mess up the timing while doing it!

[@mike21222]

Does the car show any codes when this issue occurs?

[@jhonatan7277]

Nope

[@scottfree2929]

I have a Haynes guide, metric socket set & gift card to Harbor Freight. But, have a ?. 3:44 upper oil pan?

[@joselopez1544]

Do you have a video on how to repkace the oil pan gasket upper?

[@estrelladelnorte1308]

change your oil?? whats that?

[@javibraap9670]

Hi can you Adjust the tensioner without taking the the entire cover off ?

[@twoeightythreez]

Tensioner adjusts using oil pressure

[@jmf8134]

I had the same problem with my 2014 Juke SL manufactured on November 29,2013. yet Nissan Canada looks at it as a 2014 model. Not covered under the Voluntary Recall Campaign P-4213 that covers all Juke models 2011 to 2013, Service Bulletin SB-10055923-4231, Valid from Sept. 22,2014 to Oct. 30,2015. Yet the problem of timing chain stretching wasn't discovered until May 5,2014. So I had to pay $2,440. out of my own pocket for the repairs. So why was my Juke not covered? Nissan has a problem with Model and Manufacturing dating!!!!

[@ernk75]

did you drop the engine or leave it in

[@SuperScareface1]

wwccauto......I just rebuilt my 08 Nissan Sentra and it started right up no problem after assembly but it seems to have the same noise as in your video....im not very experienced .....the chain looked good so I didn't change it nor the guides....it seems the noise is from the valves like a diesel engine.....I don't know what it would be.....help....thanks,

[@jerrellhaynes4703]

SuperScareface1 noise travels through metal,hard to locate,might try 5oz of sea spray in oil& one can of sea spray in intake first to clean oil ports to head&lifters first.

[@sandrarose8957]

Will you please answer my question? Please I don't hardly have anyone to help me and I need help bad.

[@200horsepower]

2004 maxima with 104k miles ,same noise, is very hard to do the job?? Do o have to remove the oil pan in order to remove the bolts for time cover?? Thanks

[@melvinriddick7325]

Yep

[@200horsepower]

@@melvinriddick7325 I ready hate thia car

[@melvinriddick7325]

I do not like Nissans because of the timing chain problem it is costly n plus if you no how to do the work you dont want to do it, I done one and it sucks, now this quest,smh, I have to do it again now right after I'm selling it

[@rockyqualls6878]

can anyone tell me where the timing marks should be on the pulley of the crankshaft so I do not have to tear it all the way down

[@Safsejv-ih2ss]

rocky qualls yes

[@thezaytinidude]

Can I send you some videos so I can diagnose my 2007 maximas noise?

[@milfordcivic6755]

Datsun isn't what it used to be....definitely the lower end of the Japanese car industry.

[@melocitomelopongo2177]

Question folks! Does anyone know what gaskets or seals are under the upper oil pan? I have to tackle noisy chains but could not find any info on the gaskets. Does the upper pan use liquid gasket?

[@jasonbeaulieu4979]

yes it is liquid gasket Nissan calls it threebond part # 999MP1217FPP . there are gaskets in the aftermarket but i wouldn't use them.

[@ferbsnissan]

The sludge is also from taking short trips all the time and not letting the vehicle get warmed up.

[@poopedonyourchest799]

Doesnt take long for an engine to warm up

[@sandrarose8957]

I sure hope you can answer my question. Nissan maxiam 2002 code p0011. In 2004 camshaft sponsor replaced recalled from factory. Car is making that noise but was wondering could replacing the sensor be a good idea before doing the timing chain? Could the bad sensor cause the noise?. Please answer and thank you. Sandra or hoopy lol.

[@papitosabe]

Sandra Rose check some Nissan and/or maxiIMA specific forums. Do a search there and both on google for "p0011" and ask some questions there. I'm sure you'll get answers.

[@shahidhumayun787]

Its mean the car engine is dead?

[@jasonbeaulieu4979]

it's not a tensioner guide, it's a slack guide

[@mckoylach1622]

My 05 murano has 140000 miles, it runs great,quiet but when I accelerate a bit hard, it makes a rattling noise,if I accelerate normally,no rattling noise. Could that be the guides,also ?

[@quentisowney766]

Same issue

[@lanzonex4WD]

Nissan should go back to TD/QD and slap a 4valve cylinder head..

[@tbirdpimp07]

Lol that engine wanted to commit kill itself

[@josephmoran2006]

My 2005 Altima SE-R did that for a few weeks. Now, it sounds like you hit a pot a few times when you first crank it over, and then it goes away. Does anyone know what this could be? I was told that it isn't a thrown rod because it doesn't sound like that all of the time (only start up and sometimes when its about to shift). Has anyone else had this sound on start up??

[@kendallrand296]

I have that problem on my 2006 nissan altima what is it?

[@josephmoran2006]

Kendall Rand it's a spun rod bearing. I am replacing my motor due to this. These motors are AWFUL. When something goes wrong be prepared.

[@kendallrand296]

How long you think I can drive? And what you think caused it?

[@josephmoran2006]

Kendall Rand these motors have a problem with the oil system. You can look it up on forums. I think the oil pan isn't big enough and ultimately my oil pump failed and spun the bearing. I wouldn't drive it at all. You can replace the bearing but it will fail again.

[@kendallrand296]

Thanks for the tip.

[@haycall]

Thats what happens when you use cheap oil.

[@ernk72]

haycall happens with good oil too.

[@sulameyerhomes933]

It's not cheap oil. Two timing chain tensioners and a tranny on my '05 Maxima. Only 90K miles!! Easy freeway miles at that. I live in Phoenix.

[@jakobproffer7194]

That's not even the problem lol

[@fireblade639]

is it posible to remove without removing the upper oil pan???

[@johnkimmel2612]

+fireblade639 Yes you only need to remove the 'lower'oil pan to do the front chain (and even the 2 rear chains). I think that author of video must have misspoke when he stated that.

[@guesme307]

I followed the same process, just replacing the tensioner & guide. After putting everything back together, I am getting P0011 (Advanced Timing Cylinder#1) & P0301 (Cylinder# 1 misfiring), do you know what could cause this ? Do I have to adjust the timing now ? I didn't move anything in the belt other than just putting the tensioner & guide. Any jhelp from anyone is appreciated

[@guesme307]

This is how I fixed it...I had the timing jumped while releasing the tensioner pin. If it helps anyone. my.justanswer.com/question/index/f2233e670fe04689a8cb357d65210089?continueTheConversation=False&comingFromAdservEmail=False&ratedThroughEmail=False&rating=0&paymentType=Unknown

[@gerritvictor1110]

Hi. The timing chain on my 2004 X-Trail was replaced last month with new parts at a dealer. Upon collecting the car a whining noise emanated from the cover according to the dealer. Can this be correct? I am just pissed off at the bloke who stole millions from Nissan. The (expletives) should have taken the cars too!

[@MrVespafreak]

How much it will cost to do a job like this one?

[@DonVerchi700as]

Hugo Booo 700-1200

[@Kyronsk8]

Hugo Booo sadly the aforementioned 700-1200 is no where near what I was quoted. I told them the problem and he goes, 'Oh you need your engine rebuilt, that would be 4 thousand dollars '... I might as well buy another one

[@DonVerchi700as]

Kyron Weaver​ if you timing chain jumped teeth or your car went out of timing than yeah something is damaged. But if you just hear timing chain noises like the tensioner or the guides fail than its just a timing chain set replacement!

[@JoseMorales-py6sy]

Might be too late but, I am having my engine rebuilt due to a head gasket and it is costing me 1400 with resurfacing, gaskets, new valves, and new thermostat. My engine is taken apart now and my mechanic is just gonna charge me the parts for the timing chain (200) to install. When your rebuild the engine you have the option of REbuilding it with new parts. so if your mechanic is charging you over 2000, with the excuse of adding a timing chain.. you're getting ripped off. With 4000 you can easily get a used or even new engine according to the car.

[@johnnyirenchee6459]

+Kyron or try another mechanic for another opinion.

[@ListlessSpectre]

plastic? fucking PLASTIC?!?!?!?!?

[@tammydmilledge336]

Nisaan Wants 1,900 to fix my car it needs this very same noise

[@metoon3092]

Is it a V6, 3.5 ?

[@alvaro93364]

Too dark, can't see anything. Do better

[@davidrubio4954]

Mucho bla bla bla i nada de acción

[@hannibal1319ify]

all Nissan 3.5 engines are crap!!!

[@imnota]

GABRIEL GOD Are you aware that mercedes,ford,bmw,and many others have the exact problem with timing chains? Chains are crap,belts for the win. Better to change a belt often but easily than taking the engine apart after 100k miles to change a fucking chain and tensioners that are supposed to be unbreakable...

[@tonyv9712]

My Nissan Titan has roughly 310,000 miles and still running strong as normal. I change my own oils and use synthetic. I also add a little marvel mystery oil in the crankcase every other oil change. Haven't had any issues whatsoever.

[@sblagg527]

The 3.5 engines were notorious for these plastic tensioners breaking so your post holds no value.

[@imarchand5232]

I like how u say "but anyway". Like it's just a walk in the park for u to work on difficult engine jobs

[@chefboiii]

Had the same problem. Husband fixed it replacing all 3 chains and all the internal parts with his dad and took them well over 4 days total cost around $600. You have to be real careful to make sure the seal around the timing chain case and oil pan is perfect or it will leak oil because its a liquid seal and you have to make sure the bead is perfect and you dont rub off the bead trying to get the timing chain cover back into a tight spot. The biggest part of this job is removing everything thats in the way around and under the timing chain case including the entire top of the engine

[@ramblingrebel6811]

Total bullshit.. you do not need to remove the entire top of the engine

[@catfishsnagger3284]

You need to remove the upper intake manifold and both valve covers. Only thing left is the intake manifold and cylinder heads so pretty close.​@@ramblingrebel6811

[@whattobuy1793]

What would it cost to fix? I have that same problem with my 2005 quest?

[@spooler7828]

It is not only the miles, but also the time. If they went over 6 months before an oil change, this can cause the problem. The real reason is the oil was not changed properly via time or mileage. Hope you changed the water pump at the same time.

[@jamesofalltrades4359]

Your a beast..... the Maxima has the same engine same problem. But with the max u have more space. Most people with the quest drop the engine.

[@pichass9337]

"more"?! Jesus, I must be looking at my engine bay wrong

[@mangoexpress8523]

i thought my click on my maxima was bad lol this is horrible. That engine is hella dirty too ha

[@thomascampbell5377]

MangoExpress85 put

[@christiangriffith225]

I have a Maxima too! It has 174899 miles on it

[@77jaktin]

Also, what would cause it to rattle on start up for a quick second then stop? And to have it going on for 2 years now without getting worse?

[@johng8888]

Refuse to let her go lol

[@xangobaun]

thank you for the video pointing to the problem but i wished you had a video how to take the guide off or at least point to what needs to be done i have been looking for that video or forum but to no avail.

[@Osamabeenleanin210]

Four years later and there still isn't much info on the topic...how to fix it wise.

[@dennisswift8848]

how long can it run like this before it causes a real problem?

[@LibertarianCoconut]

Great video. Have a question. We have a 2005 Altima v6 with 73k miles that also has noise coming from the timing chain. I used a screwdriver with my ear to the handle and it sounds like the noise may be coming from the upper guide instead of the tensioner guide although I have not taken the cover off to verify it's the exact same issue as this one. It sounds similar. Since the chain is supposed to last over 100k miles, can I change just the tensioner and the 3 guides without removing the chain? Or does the chain have to come off in order to change the guides and tensioner?

[@wwccauto]

You could replace just the guides and tensioner if you want. The chain on this engine seemed perfectly fine but it was replaced because by the time you get in there you might as well do it all. Usually all the parts come in the kit anyway. Having said that, the secondary chains that go between the cams and their associated tensioners require more time and effort to get to, but some may choose to leave them alone. Ideally you should do everything behind the cover, but ultimately it's up to you, and I think you could probably get away with just doing the guides and tensioner if you really wanted too.

[@lokopoko2543]

my Nissan Maxima 1997 turns on but it won't drive when I switch gears it makes a harsh noise when I placed it back to park...is the transmission bad or is it a sensor please help

[@MrArtVein]

Feels weird to say thanks for making my heart sink, but thanks 😢

[@chilledboost1982]

What kind of crap oil were you using

[@deasttn]

Murder oil

[@melloyellogsxr]

Lol murder oil 🤣 THE DAYTONA 500 BROUGHT TO YOU BY... MURDER OIL #1 IN ENGINE DESTRUCTION.

[@melloyellogsxr]

it wasn't his car it was a customers who promised they changed the oil every 4000 miles and I'm guessing a girl customer because anytime a girl tells you i promise it's a lie.

[@SenorAhole]

Great stuff, I think my guide has fallen off as well.

[@lazarof26]

Did you have to move the engine to remove the cover for the timing chain ?

[@jhonatan7277]

I believe he removes one engine mount

[@tatycancel8687]

To whom it may concern: I have a 2004 Nissan quest 3.5 L engine and recently the timing chain was changed when I got the car back I was getting a code P0305, I installed new spark plugs you coils and new injectors, and I also check compression which was excellent any ideas as to why I'm getting this code? Is it possible that the timing chain can be off one tooth?

[@jerrellhaynes4703]

If you are off even one degree you’ll know it,back fires&shakes engine& sounds awful,likely just needs code cleared,try disconnecting - term on battery for 5 minutes,if that fails need a good scanner to clear.,

[@yobi8575]

have this problem on my 2004 Lincoln aviator it rattles on the start for a brief 4 seconds which I know is the tensioner but while it's running either parked or on natural it will be a clicking noise exactly like the one on this video but not that bad but goes away when I accelerate. What can be the clicking noise? I know it's coming from the timing chain area

[@DonVerchi700as]

Yobani Gamboa échale Lucas cuando cambies tu aceite y eso le ayuda un chingo

[@killabee623]

No wonder. look at all the sludge. did you change oil?

[@lakimorezimanyiwa9695]

I changed timing chain and i drove for abt 600km and it started again producing noise wat could be the problem

[@sharonda6413]

Mine is doing it now where can I get my parts from so I can have the work done to my Nissan

[@Nosferatu10]

To me that sounded like your needing a valve adjustment, I had the same problem same ticking noise. And after the repair everything was gravy

[@sblagg527]

Why would the valves need adjusting on an engine with hydraulic (self-adjusting) lifters?

[@Nosferatu10]

@@sblagg527 not sure if they do have self adjusting lifters. I took it to the infiniti dealership that's what they told me. It's a common problem with the G35.

[@monstrito1987]

great video man that is my problem with my car right now i went to the dealer and they quote me 2300 to fix it it the about right or not

[@bigsid1984]

2011 maxima same issues thanks man

[@denverfan88]

would a 18 VQ35DD be the same issue possibly?? p0014/17 noisy chain on cold start and still heard while running not as bad tho

[@williamrussell9114]

What's the cost of a full timing chain and tensioner guides typically cost?

[@devilorangel4249]

William Russell $1200-$1800

[@crystalhernandez7386]

I live in San Antonio Texas aint know way Im paying 600 to 1200$ to replace the timing chain and I have a 2007 3.5 Nissan Altima its a bitch to get to the chain. You cant take it to pep boys or the dealer unless you want to pay an Arm, Leg and a Foot you have to shop around there has been too many times Nissan has quoted me outrageous prices. So if Nissan or pep boys or the big name Auto repair shops says dumb shit like oh its going to be 900$ to fix this somewhere its all just a matter of shopping around will fix it for alot less. Me myself purchase the parts myself than take it to a mom and pop mechanic that you can trust they wont charge you dealership prices. My 2007 Altima runs like a champ with 130,000 on her thats with full synthetic mobil 1 extended life and mobil 1 air filter, CVT transmission fluid change every 30,000 miles is a must for these Nissan CVT transmissions and the fluid is expensive I may add if you take proper care of your vehicle then it should last a long time and I drive the shit out of the V6 engine you can hear me coming from a block with my straight pipes on it you would think its a 350z or g35 the way it sounds

[@Kamdeboo-kz7lo]

What does it sound like when you start the motor?

[@danielebrparish4271]

Clicking noise, especially when the engine is below operating temperature.

[@SaidSaid-dt8wz]

At how many kms it should be changed?

[@truthsearcherforever3211]

PCV valve needs to be change so oil slug stops

[@skillz1855]

shitty design just like the older BMW V8 motors ..these VQ engines use oil as well

[@MrTrinidadgavidia]

Hello to all of you! question, i am not a mechanic but i know how to play with tools - if i follow your instructions do you think i can do this alone?. i have all the necessary tools, the mechanic wants to charge a lot and i don't have the money to pay. please advise.

[@bda7dd30]

The Auto Rules what symptoms did you have i have a 2005 nissan altima and i am getting the engine code p0303 missfire in cylinder 3

[@barnzmartin4013]

Does the engine still wynd and the cam still spin if theres a problem with the chain, started it up cranking ova but not starting opened up oil cams still turning, is that still the problem though, cheers for any help.

[@waynelewis8710]

That's most definitely a timing chain mine's make a ticking sound I know it's not timing chain mine is probably lifters so this video helped me I thought mine was a timing chain thank God it wasn't

[@ryans9029]

Ahhh... The old myth that "synthetic" oil will dissolve sludge... Lol synthetic oil is still dino oil in the US... Zero risk of dissolving anything.

[@samj1012]

You agree that Nissan engines are unecessarily complicated and time consuming to repair. When something goes wrong, mechanic needs to remove so many parts to fix the problem ?

[@stumpmtsr]

Took the timing cover off and fixed the tensioner. When I put it all back together it apparently jumped timing. Now it's out time. Both cams are sitting at 2 o'clock. Ugh. With an interference engine how the heck to you fix it without taken the top of the engine apart? Turning the crank doesn't work because the cams don't line up at all.

[@jerrellhaynes4703]

stumpmtsr now it gets complicated,get a manual to find out how many degrees off top dead center to set it,,you have to find out which cylinder is #1,pull the spark plug on #1&put a long screw driver in the hole,with a breaker bar rotate the engine(turning the crank shaft clockwise till the piston pushes the screw driver all the way up)that puts #1 cylinder at top dead center.now rotate further to degree book shows for your engine(both lifters should be level&valves closed when top dead canter)when putting on the chain expect a little kick back,so recheck degree mark after installed,repeat if gear moved off mark when you check till you have degree(4 to 8 degrees off top dead center.you better get a good Manuel,hayes preferred) this happens to be common problem because the kick back off sets the degree mark.live&learn,good luck

[@jpeg.eric1]

It’s the tensioner and the cam phaser itself specifically

[@jpeg.eric1]

I just had to fix the problem on mine

[@briannaholmes3462]

Hi, I have a 2005 Nissan Quest and it’s making a Loud rattling noise and also shakes on the side where the motor is ....can you give me a few notes please on what I need to do?

[@Solodolo305]

I have this issue with my Infiniti g35. When I drive it on the highway at high speed and release the gas pedal I hear the timing chain making a loud noise spinning

[@jamiegrose2854]

i have a 2010 nissan frontier le and the muffler has holes in the bottom. i sometime here a rattling sound from muffler. would the holes cause the sound

[@jessicacruz8157]

hi guys

[@sofreshandsokleanempire5023]

Hi

[@johng8888]

I've had the same problem 3engines later on my 2005 maxima 6speed manual. Lol

[@Universal.G]

This is reason I got rid of my 05 altima. Garbage design by nissan. I miss it, really sucked... I wonder if Nissan fixed this issue in the newer vq engines.

[@taycan24]

Lycanthropic Paranoia Yes they fixed the issue

[@eminiscalperpro9729]

look at the sludge, this engine did not have proper oil maintenance . no wonder the guides are shot.

[@2pacnasgame]

So did the owner of the car say what kind of oil they use something they told you made you assume it wasn't synthetic right just asking I buy synthetic just wonder if it's worth it