NLR35 - 3d printed Nanolongrange digital FPV drone

[@AerialWaviator]

Impressive Nanolongrange design. Seeing used only ~500mAh to travel out 900m before turning around at 8:50. This suggests can travel 6-8 km on a flight.The constraint being video (antenna limitations)

[@Unboxingexperience7]

yes, it is highly efficient. I get on my digital version +10km distance but 2.1km range

[@dawn9340]

@@Unboxingexperience7how could one exceed these limitations of video? I’ve been looking at the DJI O3 but it might be too heavy for this. What else could be done to get video at a good distance / with interrupting factors like trees and houses?

[@Unboxingexperience7]

walksnail is pretty good kzbin.info/www/bejne/l4K2q3xthNV6nLM

[@lililililililili8667]

this is exactly the type of build I've been hoping for idk why all the nano long range stuff is 18650 instead of 21700

[@lililililililili8667]

just need that wokesnail whoop vtx to drop and I'll be in business

[@Unboxingexperience7]

seems it will be heavy though - 1s 75mm whoop is at 39g. I suspect the VTX-camera-antenna set to be twice as heavy as HDZero at around 14g.

[@themanindungarees]

More 3d printed drones 😍

[@Faultyappliances4]

Really liked the video. What was the total cost of making your drone? Wondering if it would work for search and rescue ? I do Volunteer work . Have a 3-D printer. Any other information you can provide would greatly help. Thanks

[@Unboxingexperience7]

you'll find more info on thingiverse and instructables. this is a tiny lightweight drone which requires specific skills like 3d printing, soldering and software adapting. flying it needs some hours of practice. you're probably better off with a dji drone working straight out of the box.

[@RyanQuellet]

Hdzero cam lens needs to be refocused. Cool video

[@Unboxingexperience7]

thanks, will give it a try

[@recifestargazer2192]

Any hint to focus it, @Ryan Quellet?

[@thirtythreeeyes8624]

@@recifestargazer2192 Try a focus chart

[@RyanQuellet]

@@recifestargazer2192 go outside and focus the lens on a far away object like the treeline

[@seantuitz]

Very nice! How is the ABS+ in terms of warping and strength? I considered buying it for my Cr 10 which doesnt have an enclosure, as they say that it warps less, but wasnt sure as they are basically no reviews on it.

[@Unboxingexperience7]

ABS+ is superior to PLA+ and PLA. The latter warp after printing in sunlight and heat. ABS+ is warping during printing. I had no luck without enclosure so I used a blanket.

[@hockeyrounds]

Very cool. I have a 2in quad I'd like to start doing micro LR with.

[@Unboxingexperience7]

Go for it!

[@Leeengold]

Is this Donauinsel in Vienna? Is flying there allowed?

[@Coolfwip]

Thank you for this

[@pukki34]

Needs a 2s version.

[@OusyedChinli]

Hello Unboxing experience your name should be Experienced Builder!! with that out of the way just a question. Is the casing on the HD zero flight unit just for protection or is it also a Ihs? (heat shield)?

[@Unboxingexperience7]

it primarily protects from physical damage

[@TechOffZedOn]

Hey, great job. Thank you for doing this. Is this version superior over the Nanolongrange_v2, or just different? If so, what are the poros/cons between the two?

[@Unboxingexperience7]

V2 is lightweight and more compact. NLR35 is slightly bigger and beefier and, thus heavier. My top 3 pros for NLR35 are: Magnetic connectors are great, you don't need to weld/solder Liion batteries. GPS locks very fast due to different type and mount. Flexibility: props up/down, props up to 3.5", battery on top/bottom, FC top or bottom

[@TechOffZedOn]

@@Unboxingexperience7 so the v2 has longer flight time?

[@Unboxingexperience7]

didn't test endurance. probably slightly higher.

[@TechOffZedOn]

@@Unboxingexperience7 Thanks :)

[@evren.builds]

What are those magnetic connectors you are using for the battery?

[@Unboxingexperience7]

It's in the thingiverse/printables deposit. 3d printed caps for 5x2mm magnets which push Nickel strips to the battery terminals. It's something I ve designed and tested.

[@evren.builds]

@@Unboxingexperience7 thanks a ton ^^ great build :)

[@Amzdgg]

Do you have any issues with heat? having the fc/esc and the hdzero board close together without the heatsinks seems like that would get hot. On the other hand you dont have much blocking windflow so might be fine?

[@Unboxingexperience7]

No problems so far except a broken cam without a crash. But I never used it in hot weather.

[@larssmith6780]

I was looking at the thingiverse page and saw that it was printed at 20% infill, why not higher? Too much weight?

[@Unboxingexperience7]

yes.20% seems to be a good compromise between weight and robustness.

[@brezovprut4431]

Is it too much to use 1303.5 motors on single 21700? Have you tested 3.5" biblade props (T3.5x2.2x2 HQprops)?

[@Unboxingexperience7]

1303.5 with high kv around 11000 are perfect. The Hq biblades are drawing too much amps (>18A) and this setup was struggling. They might work on an ultralight carbon frame version. I guess a 3516 biblade would work fine.

[@Meleonlight]

Do you have a 4 inch frame?

[@Unboxingexperience7]

No and this one allows up to 3.5". To me, 3d printing only makes sense on smaller frames due to additional weight.

[@ningcraft]

Is this usable with all the parts from the nanolongrange v2?

[@Unboxingexperience7]

yes, only the gps mount is for the smaller and lighter namelessrc tiny gps

[@jeffclassics]

Truly amazing Bro. What motor kv did you use? Thanks. Might build too. In the hdzero build, did you have spare uart for the gps but intentionally not put?

[@Unboxingexperience7]

11500kv. no there was no spare uart for gps... newer boards have spi elrs so you have 2 spare uarts. then gps will work too. I ll do an update with a fancy carbon version with gps hdzero/walksnail. so stay tuned!

[@Unboxingexperience7]

11500kv. This was on an old board without a free uart. on the newer version I ve used a darwin aio with a free uart for gps

[@NRG_FPV-po4rx]

whats the benifet of pusher vs puller drone?

[@Unboxingexperience7]

I wanted to have the props out of view

[@NRG_FPV-po4rx]

@@Unboxingexperience7 that makes sense

[@thisguyeddiex7136]

I really like your scale. What’s the name of it? I want same thing

[@Unboxingexperience7]

look for coffee scale, it also got a timer. i found mine on aliexpress

[@pedroazuajebolivar603]

Hey men awesome video! Can I contact you for a scholar project for our students to involve them in electronics and drones? If we can get at least a little help will be great !

[@Unboxingexperience7]

here is a bit more information www.instructables.com/NLR35-Single-21700-3d-Printed-Nanolongrange-Digita/ just ask if you need more details

[@pedroazuajebolivar603]

@@Unboxingexperience7 thanks you For the respond! Hopefully I can make one to my own first!

[@s001software9]

Which 3d printer is that?

[@Unboxingexperience7]

VZbot 235

[@АндрійАлєксєєв-п3з]

what gps are you using?

[@Unboxingexperience7]

NamelessRC tiny GPS

[@张草莓-y4g]

How to fix the camera on the carbon fiber board

[@Unboxingexperience7]

STLs will be released soon ;-) You can get a sneak peak on my instagram

[@FinaISpartan]

Might've lasted longer with the VTC6. About the same capacity but smaller and lighter.

[@Unboxingexperience7]

I thought so too, but kzbin.info/www/bejne/j5u7oqGwrJmap9E New Molicel 21700s have even more power and capacity over the tested Samsung 40T. 21700 is the way to go.

[@greedfox7842]

that wiring is absolute chaos...

[@Unboxingexperience7]

I reused parts from another drone

[@dstepsfpv]

What motors?!

[@Unboxingexperience7]

flywoo robo 1202.5 11000kv

[@1337flite]

What no GoPro? ;-)

[@Unboxingexperience7]

been there, done that :-) kzbin.info/www/bejne/iHWvYWeZg7mFZsk

[@maciekwojcik7648]

Hi how much does it cost

[@Unboxingexperience7]

rough guess 150$ for the standalone drone without radio and FPV goggles

[@иньянь-е8м]

это маленькое чудо !

[@АндрійАлєксєєв-п3з]

try to focus your camera

[@Unboxingexperience7]

thanks, will do.

[@АндрійАлєксєєв-п3з]

@@dloc116 what do you mean?

[@handikadika2634]

Koleksimu banyak beri saya satu please saya indonesia

[@fihsanhsk8114]

Mental pengemis