Problem: the device is running randomly Solution: replace the electronic module
Пікірлер: 24
@wreckim Жыл бұрын
FYI, there is going to be a part in this video where Robert Downey Jr. checks his Arc Reactor and keeps going forward from there. This is definitely beyond my storm trooper training, and into a jedi like territory. Awesome dude.
@dinorapineda6039 Жыл бұрын
I’ve been having the same problems, would you mind telling me where you got the parts? I tried to find them, but was unsuccessful. Thank you
@vsvnrg3263 Жыл бұрын
the bag says makita.
@shauneq9 ай бұрын
At one point, you put on rubber gloves. Is that when you were replacing the flux capacitor and didn't want to get zapped by 1.21 gigawatts?
@vsvnrg3263 Жыл бұрын
i'm having similar trouble with a dub182. i use it with a 1.5ah battery. when it refuses to work i put a 5ah battery then it works. then it will work with the 1.5ah battery for a while. i suspect dust in the switch to be the most likely reasopn. the brushes are the next possibility.
@brockmunn7858 Жыл бұрын
How did you determine that the harness was at fault? was it in the PCB?
@danielarellanes67334 ай бұрын
Where did you get it. Those parts
@medgrower1.killer2 жыл бұрын
I just bought this blower. Worked 10 minutes. Then shut off . Doesnt rev up. Thnk bro
@jamescarey6657 Жыл бұрын
Mine did too. I sent it in for repair. They replaced the module and after I got it back it ran for 10 min and quit again.
@vancester1st3 ай бұрын
It’s total junk! Mine died after shocking me. I think the speed controller is garbage?
@johnjaymesgreatadventures45037 ай бұрын
Im having the same problem with my blower as well Makita XBU03Z 18V LXT. Does anyone know if the contol module or speed control has been updated by makita, or is it just hopes that you may get a better part this time?
@paolaandreachonavera53253 ай бұрын
Como sulocionar si el daño fue en la tarjeta
@rafaelgruna400 Жыл бұрын
Coloca o link do produto que vc substituiu.
@kerritanner65582 жыл бұрын
Where’s all the left over bits 😀
@scottgreen6538 Жыл бұрын
My blower did this after a few uses.
@ricardovillanueva47452 жыл бұрын
Where did you buy the module?
@vsvnrg3263 Жыл бұрын
the bag says makita
@seanwilliams48010 ай бұрын
I’d rather just buy a new one…
@brockwhite2525 Жыл бұрын
Did anyone find a source for the new module
@vsvnrg3263 Жыл бұрын
the bag says makita
@raidop12 жыл бұрын
Looks like my blower has the same problem.
@fzghbkhvgfhhgv3524 Жыл бұрын
Mine did the same thing , I didn’t have the recite but the date stamp is located on the blower so makita cover it under their 3 year warranty service . I call Mikita and they gave me a shipping label and fix it… it was the control module also … their warranty department is great … fast , fixing and repair .. call them and get it fix
@johnlloydjohnson Жыл бұрын
@@fzghbkhvgfhhgv3524 I'm doing the same thing, where is the date stamp located
@javiercruz3609 Жыл бұрын
@@johnlloydjohnson makita serial id plate!! 3 numbers example 20.4 (2020.April)