2.3.2.5 Packet Tracer - Implement Basic Connectivity

[@vicmo5837]

You are a hero ! my professor literally expects us to learn all this on our own, without you I probably would've taken all day on this. I learn by seeing and doing so seeing you and following you has really helped me. Thank you so much :)

[@mikeh2803]

Hello! I know this is a few years after this video has been made but, currently Covid-19 has taken place in the air and my professor completely stopped teaching us. So this video is a god send, thank you so much for what you do and i hope you keep making these videos!

[@rhoades23]

I just want to reach out and say that these videos are incredible. I really appreciate the fact that you use real world examples to reinforce what we're doing in the packet tracer as we go along. I'm forever thankful for these videos!

[@monryu5760]

I am from Argentina and I am living in Spain. I dont know where you are but thanks to you I can continue my studies understanding all my work. Thank you, you are really my saver.

[@logannguyen9512]

What a savior!!!!!!! Thank you very muchhhh!!!

[@ngweixiang1489]

You're the best man, better than my lecturer!

[@misteriosrevelados8600]

dude your the best God bless u make everyhing much easier for beginners

[@dilgashb389]

Thank god for you, im in the Info Tech program at my university and I absolutely hate the networking courses. The professors always make everything non practical.

[@kennyhuang6231]

Thanks very much. This is very helpful!

[@AbCd-ts8dz]

thank you so much, this is so helpful. please make more videos- if youre still doing this 2 yrs later!!!! lol

[@JohnSmith-by2bx]

Please add more videos you do a good job of explaining things

[@TheHaruhi33]

sir ur the best for explaining the packet tracer please make more videos

[@NotCiscoAcademyHelp]

Hi Muhammad, the password for privileged mode is "class". Made sure that when you enter the password in either the running configuration or at the password prompt, that you do not put any spaces after the password. It's an easy mistake to make. Also, memorizing all the commands are difficult at first. To help, use the "?". The "?" will show you a list of commands that are available. For an example: type the show command an type the ?. The ? should show a list of all the show commands available. Hope this help. As you continue to work through the lab you will naturally remember most of these commands.

[@yuhnimpz]

Thank you for the video! It's very helpful. Can you explain why is the password for privileged mode "class"?

[@MikeyCSCS]

This was a great help to my studies. One question: While completing the worksheet, I had to enter the passwords that were setup earlier in the exercise and you didn't. Is there a reason for that? Thank you...

[@petermaguire8757]

Right on man, life saver

[@mohammadalwazsaiyed5451]

thanks a lot

[@PeaceMarker1212]

Thank you so much

[@kirillalexeev1988]

Nice job, man!!!

[@akmazam2713]

Great. Thanks.

[@MrMRgewoonrobin]

you're great

[@kelfora5289]

somone help the lineprotocol wont come up at all

[@yahmet73]

Thanks man

[@jaydoin3736]

thank q!

[@maryamalhammadi588]

why we use no shutdown??

[@NotCiscoAcademyHelp]

+Maryam Alhammadi "no shutdown" brings the interface up or turns the interface on. "shutdown" turn the interface off or brings it down.

[@hopelessnation8873]

maisonneuve rise up

[@cityasif3966]

sir after config the pc1 and pc 2 when I went to s1 and s2 both switch asking me password i gave login then but after that it ask me again switch in privilege mode. but i do not know which password should i give . I just put same as you gave . please help me to learn all this please. Because i have done Associate Degree in Electronics and currently I'm doing job as hardware and networking engineer but to be honest I do not know how to know all these things. Another question is how to remember all these commands . please help me . and i liked you videos. thank you to share you knowledge and God bless you and keep you ever happy.

[@yahmet73]

class is the password

[@piccostar69]

@@yahmet73 after that I get to S1>

[@asif2830]

sorry i have two account one is personal and 2nd is company.

[@pito01234]

thanks so much you cleared up so many questions I had. But for some reason I did exactly as you did and my score never went up.

[@asif2830]

sir after config the pc1 and pc 2 when I went to s1 and s2 both switch asking me password i gave login then but after that it ask me again switch in privilege mode. but i do not know which password should i give . I just put same as you gave . please help me to learn all this please. Because i have done Associate Degree in Electronics and currently I'm doing job as hardware and networking engineer but to be honest I do not know how to know all these things. Another question is how to remember all these commands . please help me . and i liked you videos. thank you to share you knowledge and God bless you and keep you ever happy.