CHEVY SILVERADO 19 -23 SANOOER SMOKE LED TAIL LIGHT INSTALL --BEFORE AND AFTER

[@andredickens3664]

Thanks for the tutorial. Do you have a technique for one of the tail lights, blinking fast? My Silverado has LED from the factory.

[@Cams_Way]

I installed no prob but how do you replace bulb in these taillights?

[@joshr19821]

Also, how have they held up since being installed?

[@USAlivewithGOD]

Do the hyper flash on you after the completely installed?

[@34kefu]

I have a 2020 silverado and installed the sanoer smoked tail lights with the resistors and about month later my right side tails lights started hyper flashing and the left side is ok should I take the resistors out ?

[@octanetvchannel]

I would definitely contact them and see if they say to take those out

[@kevinspahr6632]

Made in China

[@USAlivewithGOD]

Did that stop it for you from hyperplastic by taking out the resistors?

[@ThatBoyGhost82]

The resisters are to correct hyper flash. If they start to hyper flash then the resistance is not present. The resisters they send aren’t the greatest you can order better ones and try that

[@The_Big_Soup3]

Would be so cool if they were sequential

[@USAlivewithGOD]

I have sent back two sets and they sent me back to new set and still the hyper flash. I cannot get it to stop Piper flashing at this point. I think I'm just gonna put my regular light back on and just have them tinted with a spray or a film, for them to work I just tap it and it blinks and then it stops and I retype it but keep the blinker on it hyper flashing, I can't find anyone that can fix that. It's a joke they look nice though.

[@rojamon2490]

I'm getting a signal light failure warning on my truck display when activating turn signals although the lights work. Will that affect my annual inspection?

[@rojamon2490]

I contacted Sanooer and learned that my resistors may have been faulty. If you run your blinkers for several minutes and feel the resisters, and they are not warm...they are faulty.

[@frankperez3766]

How much for the OEM?

[@jameslucas4181]

Do your led lights in bed still work? If so how’d you get them to work, mine don’t….

[@chadwiederin9710]

Figure it out? Same problem with my ltz

[@deandreprince1771]

@@chadwiederin9710the resistor wires come installed incorrectly. You have to cut the wire in the resistor connector that connect to the light and swap the wire sides.

[@USAlivewithGOD]

For me they do not so am taking them off my truck.

[@TalariaDave13]

Why no reverse light

[@bksosa]

the white lens for backup light should be tinted with the rest of tail light

[@gnostikmindz]

🤣🤣when u get ur chevy.. u do that

[@bksosa]

okay ford guy

[@victoravila24]

Disagree

[@jimellisGF_Exotics]

Gonna need a set of these lol

[@81hermoso]

They look ugly the recon ones looks great even the oem look better

[@Zkgod24]

Hell no😭

[@kevinspahr6632]

Longevity??? Made in China ☹

[@jameslucas4181]

Little over a year…

[@terryhook5518]

Bed light don’t work smh and one hyper flashes one doesn’t

[@ryanhodge6700]

One of mine hyperflash too did u end of finding a fix?

[@terryhook5518]

@@ryanhodge6700 just unplugged everything than plugged back in and it works but heard the bed lights u have to cut the wires in switch the sides they wired them wrong when they made them

[@ryanhodge6700]

@@terryhook5518 ok thanks I will give that a try, what did u disconnect?

[@terryhook5518]

@@ryanhodge6700 just everything to the headlight

[@ryanhodge6700]

@@terryhook5518 alright thanks appreciate it