My father's grinder has been idle for about ten years. In summer, it was eroded by rain. The bearing was seriously rusted and damaged. So this project is to repair this grinder
Пікірлер: 29
@remcotissink2 жыл бұрын
Nice work ! Nice touch measuring the insulation. Should have used a grommet though for the hole where the cable leaves the casing. Now you'll cut the insulation slowly but surely.
@Markanthony517863 жыл бұрын
Got bored and wanted to watch restoration videos.. this is an epic video thanks for the long video.. good job bro
@maxc.gurrero98933 жыл бұрын
Marvellous video. Really appreciated your hard effort.
@metelgodful3 жыл бұрын
That was amazing that was a nice job really awesome but how come you didn't take the dents out of the front of the covers over the wheels those standout big time now you could have pounded those two things in place and it would look even that much better but you did an awesome job it just makes me wonder how come you didn't take the dents out of the covers
@oreilly3592 Жыл бұрын
I love the paint!
@Jennifer-yy2ri3 жыл бұрын
Amazing!! Very good job😊👍
@jblcontrol28crossover765 ай бұрын
7:13 Never hammer on the end of a shaft like that. The end of the shaft will mushroom slightly and the nut will no longer thread onto it properly. Protect the shaft by threading on the nut to a flush depth so that the hammer hits both nut and shaft at the same time. Or, use the correct tool for this procedure... a press.
@evelynsia460 Жыл бұрын
What's the name of the liquid u use to clean the bolts?
@rustydogrustydog91912 жыл бұрын
Excellent job. I would maybe consider not using the old grinder wheels as they are probably compromised.
@waltercooling89073 жыл бұрын
This project was very professional. Did you balance the wheels? On your install, one looked terribly wonky. Most actually are, unless they are high-grade stuff. Very smooth, enjoyable video!
@customrestoration53173 жыл бұрын
Great work 😊
@metelgodful3 жыл бұрын
You did a real awesome job on the grinder but the two things you should have finished was those smashed in dents on the front of those covers for the grinder and the rubber pad for the bottom you probably could have took to the sink and washed with soap and water I bet it'd look a lot better I mean cuz you took that thing all the way apart to the even taking the motor out of the casing I mean you went that far as you did why didn't you go to that extra couple minutes and finish those two things then it would have looked brand new and maybe clean that label a little bit too you'd be surprised with soap and water can do I took a plastic gas can that was dirty and left outside for a long time but a new spout installed an air vent and washed it with soap and water it looked brand new when I was done
@dbeckley433 жыл бұрын
You do great work but take some advice and get some brass punches and avoid striking hard metal together this will eventually save you a headache.
@_BLANK_BLANK2 жыл бұрын
Did you put the screws in muriatic acid to get the rust off?
@sureshlingabathina7 ай бұрын
Excellent
@TEST-xr1ki2 жыл бұрын
Hello what is the liquid that remooved the paint? Nice job i will follow your videos.
@joseanecruz39146 ай бұрын
O nome do equipamento 11:40 que gira manivelas?
@ikju-il4ok2 жыл бұрын
Didn't see any capacitors? Can anyone help?
@robc84682 жыл бұрын
Yes I don't see how that motor can run without a capacitor since it is single phase motor not 3 phase did he put a capacitor in off camera?
@persioboni93733 жыл бұрын
Muito bom.
@alessandropezzella45053 жыл бұрын
Wow
@stenolomi87835 ай бұрын
Uguale identica alla mia
@Markanthony517863 жыл бұрын
Whats the liquid u used to get the old paint off?
@repairrestoration42323 жыл бұрын
Paint remover
@oldgadget13 жыл бұрын
please dont use a hammer on a grinding wheel. bad things happen to stones that crack and fail
@SubramaniamLakshminarayanan3 жыл бұрын
So true. The cracks aren't visible in a stationary wheel, but when it spins at 10000+ rpm, the centrifugal forces are enough to disintegrate the wheel into many pieces of flying missiles at that speed. Catastrophic to even imagine one. A correct way to test any grinding wheel, before mounting them is to strike them like a cymbal, with a light nylon rod. A clear resonating metallic bell sound indicates a sound wheel, while a dead sound surely means it is cracked. That apart, a good restoration job, well done.
@robc84682 жыл бұрын
I am shocked he "restored" those grinding wheels kind of like riding around in a vintage car with 50 year old tires aka "not safe".