Onkyo HDMI Rework DSP Chip ACHI IR Pro SC

[@magalimoreno2084]

Just WOW! The perfect setup and obvious craftmanship capabilities to resucitate all of the almost dead ONKYO AND INTEGRA receivers all over the world... jesus christ... GOD BLESS YOU MAN!

[@ChuckNorris-lf6vo]

Nice music bro. Dynamic bass.

[@eletrons234]

Great job I did on my onkyo about 4 years ago today it had the same defect I think it's a component defect

[@chrispelletier8860]

well that's one hell of a setup are you a professional or just someone's thats gotta a lotta of excess income. anyways this is a great example of the correct way of doing it. even though most of us don't have the equipment to do so.

[@MrAmity009]

What temperatures are you working? And what are the steps for the reflow settings?

[@OromiyaaTiyya]

Hi, so If DSP shows ????????? -as per the diagnose method- instead of a number then what does it have to be done? mine is a NR515 I got only analogue sound out from zone2! used a heat gun with no success, but using that diagnose it gave me the ???? on the DSP rather then the number it should.. would appreciate the help.. Thanks

[@tonict2302]

Can you please tell us your ACHI settings. Golden regards...

[@ruudbrammo1998]

Which Stencil is used with this and which solder balls diameter

[@BerserkStyle]

I have a Onkyo-tx-nr808 with a DTS chip that needs some work. Do you still do this work?

[@edmusic4908]

Thats a awesome set up. Do you do this for people that have these issues in the recievers? I have 3 of them that need to be done. Any help would be appreciated.

[@kamilkwiatanowski3923]

Hi mate. What type of solder paste did you used in this video?

[@luciferHV]

Hello :) what size of the sieve?

[@petertimaeus4433]

Wo bekomme ich das Lochblech her??? Where can I get the perforated sheet???

[@stormanimal83]

Hallo mein Freund! You can speak Deutsch to me :) Das war ein kompletter Satz. Aber nicht billig. Schau mal nqch einem Bundle BGA Rework bei amazon oder ebay. hatte es damals von ebay... 10 Jahre her ungefähr

[@izzzzzz6]

isn't it possible that it's simply the capacitors that need changing on this board on most of the amateur onkyo reflow vids? It's just the heat people are using that helps the caps temporarily. I'm sure there are some bad BGA joins on some amps but i'm not so sure that mnost people are diagnosing correctly. I would like to see some people apply pressure ton the bga to prove their point!

[@stormanimal83]

yes, of course. U have to Check that First before doin this repair...

[@3of12]

Sometimes, yes, but the power rail for the main amp goes through this and BGA failures were very common and it is known to run hot. I have one that is currently without power to the main amp so I could try applying pressure to the decode IC. It turned out to be the correct diagnosis on failing PS3s and macbooks in the same time period, bad BGA balls.

[@vizhuvaiananth9398]

Onkyo Av Receiver TX-NR609 HDMI Board Available ?

[@RAZOR-xu2sd]

Hello, I am writing from Chile, you can tell me what ball and temperature you use for the dts, I have a nr616 which was left without sound and does not recognize the Ethernet cable, I would be very grateful if you help me, regards.

[@68pishta68]

same here. does yours emit sound when on FM and in direct mode? Mine does but no speaker 'matrix' shows up on display.

[@DrDroogkloot]

Hi i have a 414. There is no video but sound does work. Also the network is working. Is it the same chip causing the fault?

[@nabukodonosor777]

I don't think so.

[@nikhilprakash3391]

I have also problem with my hdmi card.onkyo tx-nr555 av receiver.hdmi card is not available in market.

[@stormanimal83]

no... u cant bis them. Whats the matter with it?

[@stormanimal83]

buy... Not bis

[@RickLWright]

Will you fix mine?

[@stormanimal83]

Hi there... which model of Onkyo do u own? Is it the HDMI Board for sure? Sometimes the receivers have other issues.

[@RickLWright]

@@stormanimal83 I have the TX-NR 3008. I don't know for sure what the problem is for sure but I have no sound and the speaker icons on the front panel don't click on. According to most videos on KZbin, the problem is almost always the same chip, the Q3001. In my case its a TI DRS chip. I could give you the full number if that helps. I was going to try to reflow the solder today. I bought flux and a heat gun. It seems to work in the many videos I've seen. Since the unit is doesn't work, I've little to lose.

[@RickLWright]

Sorry, DTS chip

[@stormanimal83]

@@RickLWright yes. then u are right. it might be the dts chip for sure. u can find it out by opening the case an position a halogen lamp exactly above it. let it run for a while. if it clicks an the speaker symbols appear again after some time it should be reballed....

[@RickLWright]

@@stormanimal83 I had hoped that once I reflowed the solder and applied a heat sink, it would be a permanent fix. Curse Onkyo for not standing behind a manufacturing defect.

[@sharfazhameed6382]

This kills real skill. I can do this job better with a cheap hot air station. Dead serious. If machine can do all these where is the price for the skills and this machine still leaves huge solder blob. So guys with poor skills will make this set up look like a bakery.

[@3of12]

you could do that. but more than a certain amount of time at the necc temp will damage components. the rework station is for precise reballing that is a permanent fix.