ONKYO TX-RZ840 9.2 Channel IMAX Enhanced, Dolby Atmos, DTS-X Receiver

[@zombielandiii2711]

Hello, Spare! Thanks for the review. I really love your channel because you leave nobody out🤟🏻🤟🏻🤟🏻 one day you bring us a super HiFi plus equipment, and the other day you share with us a more to earth stuff. To me, your channel is improving every day. Cheers!

[@gungfuchuckify]

I got the onkyo tx-nr686 polka 110 subwoofer and 4 t50 bookshelf polka and 2 Sony Up fire atmos speakers on top front wall mount and a polk center with 6 speakers one tweeter I appreciate all of your videos Thank you for helping people Enjoy home theater experience and movie reviews

[@therealshanelee]

👍👍🍺🍺

[@alanblackburn4101]

Thanks Spare that was a review I was waiting for. I follow a lot of reviewers on KZbin but you are the only one to review a Onkyo receiver. I have been a Denon user for decades but now changed to Onkyo since i listen to the TX-RZ830. It seems that lots of guys are into Denon or Marantz as far as receiver are concerned. i would love to see a comparison between the Onkyo RZ840 and its direct rivals from Denon and Marantz. That would help me make my choice. Keep it up pal.

[@jimmy2shoes75]

I have a Denon 3300 and was interested to go back to Onkyo after many years, how would you describe the sound compared to Denon, like you said there is little info out there on you-tube on Onkyo

[@nevergone3424]

@@jimmy2shoes75 Not the person you're replying to, but I gifted my brother a Black Friday Onkyo receiver from Best Buy ( I think it was the 686?) It was one of the lower end THX certified receivers running for $250 or so. So knowing how his system sounded previously ( since I handed him my old Denon 1909) I was pleasantly surprised how full and robust the Onkyo sounded compared to my old 1909. I didn't even bother using Accu EQ, because it already sounded that good. (Even compared to my old 1909 calibrated with Audyssey or bypassed!) In short, Denon is anemic and tinny opposed to Onkyo being robust and full. On a side note, my 4300H does have preouts for my amps, but without it, Denon's internal amplification pale in comparison to Onkyo or Yamaha in regards to sound quality. I honestly could care less about Audyssey, in some cases it does more harm then good. I remember watching this one scene in a movie with Dynamic EQ enabled at low volume. The scene was in a club with music with dialogue in the background. Audyssey's algorithm kept adding more EQ on the lower end of the spectrum (100-250hz) to the point I could barely hear the dialogue. Some people swear by Audyssey. Although, every system I heard with XT32 makes the sub anemic or overbearing after calibration, including mine. We could compare other receivers such as Arcam and what not with Dirac live , but that's an entirely different price point.

[@gtric1466]

@@jimmy2shoes75 Denon has a warmer sound but for me especially with 2 channel for music it's seem to put a vail over the music. the Onkyo is more neutral and live sounding. and power to power both mine where rated @ 100 watt's but the Onkyo blows it away. sounds like your at concert.

[@jimmy2shoes75]

@@nevergone3424 Only saw your reply there ( lol a year later) Ya I agree with a lot of the points you have made, for most I think Audyssey serves it's purpose well and is fairly user friendly. DEQ is a preference that I don't care for too much, but I think most people do use it whom are not looking for "perfection" or clarity. Dirac is for me a big step up no doubt

[@jimmy2shoes75]

@@gtric1466 Thanks, in the end I got a Arcam for Dirac on my home cinema. I then converted one of my Mini-Dsp to a DRRC-24 and use this with my Denon for 2 channel setup. Working pretty well

[@quesnoy1]

Just bought one of these on Amazon. It was retailing for $1,099 but I got the $150 credit for applying for the Amazon store card. Inflation is crazy right now. Receivers are retailing for at least $500 more than comparable models pre-pandemic. Even this 2019 model is $100 more than it was brand new three years ago. Anyway, I was looking at the Denon X4700H as well, but it was $500 more, so I pulled the trigger on the RZ840. It'll be my first Onkyo. I've owned Pioneer and Denon. Figured I'd give Onkyo a try.

[@10MEGAMETAL]

Same here my first Onkyo happy so far here,I have it for around 3 mo now still learning how to make it better sound

[@joeykitty2892]

I'm not sure how many people will read this, but, this receiver WAS available for purchase, for a couple of days, on the Onkyo website. I was on the waitlist; was notified; grabbed one! If you're desiring one of these earlier models, join the waitlist, and hopefully, you'll meet with success. Update 7-21-21: Well, after receipt; hookup; calibration; listening, I was not happy with the AccuEq calibration sound performance. It paled in comparison to my Audyssey equipped TX-NR809, so I returned it; replaced it with a TX-NR818. Now I'm a happy camper. I don't care that some of the latest tech is missing, what really matters to me is sound reproduction.

[@SimonMaderazo]

I cant believe this channel isn't at 100k subs. Great content

[@user2144]

Simon Maderazo Why haven't you recruited 68k friends, colleagues, family members & strangers to subscribe? Simon, if you are not part of the solution, then you are part of the problem 😉

[@keepingupwiththejones2933]

Shane love the facial expressions and shoulder shrugs when you are doing the voice over. You really do deserve more subscribers. Your videos and commentary have such a professional look and feel to them. I watch a lot of AV reviewers on KZbin and you have by far the most polished videos and on screen presence and delivery.

[@nevergone3424]

Thank you for the very thorough review. I love how you were able to video capture the OSD of the Onkyo menu. Now from a Denon owner's perspective.... Only one 12V trigger! although as someone that despises Audyssey XT32 (including the mobile app) and just manually EQ's and levels their system with a tone generator and a meter. I was pleasantly surprised when I saw the15 band graphic EQ on the Onkyo. (only 9 bands on a Denon) Other interesting things I came across on your video. The support for non standard setups such as 6.1.2 and the alike ( phantom center). Which can be done on the Denon as well, but it's nice to see it a preset option on the Onkyo. Which is non existent on my 4300H. On a side note, if you're going to keep on reviewing receivers, please keep it in this format. I enjoyed watching this review , cheers. I think I might get rid of my Denon

[@AaronStarks]

I've been an Onkyo user and was thinking of switching to Denon when upgrading my A/V setup later in the summer. I'm going to use a 5.0.4 setup (both fronts have 10" woofers) and this Onkyo has intrigued me and may keep me on their train.

[@nonametofame]

I went through 4 generations of onkyos and had pretty good luck with all units. No hdmi issues. I still own a 805 though its been shelved for years. I would probably get a unit like this as I run 5.2.4 but im glad ive been able to try out different brands, and chase after a sound signature I enjoy more for 90% home theater use. I do think the reason onkyos are affordable is because they don’t pay a license fee for room correction and developed their own. That’s something I don’t miss at all.

[@Edward135i]

0:54 Gene DellaSala TRIGGERED!

[@therealshanelee]

😆

[@Squashball]

Indeed, shaaaame!

[@povertime6381]

Love the channel, but I hope Onkyo paid you well to spout that power number. Is that the power number on Tuesdays and Thursdays or only on February 29th of this upcoming leap year?

[@lexiewilkinson9703]

Well Shane my taught on the Onkyo it is an amazing unit and im really glad you did a review on it! peoples tend to go with marantz and denon but on my side i find Onkyo pioneer and integra to be an excellent choice.. paired with power amp this make and unbelievable bargain pre pro

[@keepingupwiththejones2933]

B&H Photo getting a nice little shout out. Onkyo has done a nice job with the sleek lines and simple front panel layout. The GUI has a really nice modern look to it.

[@maxpower78-15]

Im contemplating buying this unit. Thanks for making this video

[@Angel-AbC9]

Please keep reviewing Avr recievers awesome and enjoyable to watch plus very educated.

[@nixxhimself]

I need one of these in my life

[@greebuh]

If you want 4 height speakers, you can also just use 5.1.4, you don't Have to have external amplification unless you want a full 11 channel set up.

[@StevetheTechBro]

greebuh right thats what I was going to say

[@BadassMoFo.]

What about the supposed 9.2 channel setup?

[@hi-fihaven2257]

Great looking AVR. Love that front panel design. Very cool to hear that is has IMAX enhanced feature. Great rear panel layout. love all those inputs.

[@shajahanshajahan1624]

Giving 👍👍👍👍👍for showing the price! Thank you.

[@DJCooper501]

Hello I recently purchased Onkyo to replace my 12 year old Denon avr-1609 I tried to find a middle ground between the Sound Performance of my Denon I still miss my Denon I will buy one another one in the future but for now this does the job I really like your videos keep up the good work you had a really great feedback I am from Canada

[@romanlewandowski9616]

Well done another great review

[@davidrivera4289]

Onkyo & Pioneer Receivers are on my C list. A list Receivers: Anthem, Arcam, NAD ( all have great DACS, Great Room correction software, good amp section). B List receivers: Marantz, Denon, Yamaha.

[@battousai412]

Oh man u tried full range with that things low power :) I think there are better avrs in that price with better room correction software 2. It confuses me how these avr vompanies add more n more chsnnels and things like imax enhanced but cripple it with poorer n poorer amp sections. At least some are offering balanced connections n the ability to amp the three main channels. Thus, taking a huge load off tge avr amp as now that poorer amp can better handle trying full range imax enhanced stuff n such on remaining channels. I get everyone has to start somewhere but I dont even like how onkyos sound.

[@seanlacroix]

Anthem are over rated. I have a 510 and my Marantz sounds way better.

[@keepingupwiththejones2933]

@@seanlacroix agreed Anthem is overrated. Like the BOSE of AVR

[@BeefyMon]

I own the TX-RZ830, which is nearly identical. I was able to pick it up for $450, NEW, from an authorized dealer a few months ago (it’s easy to get screwed on your warranty if it’s not from an authorized dealer). That warranty is THREE years, by the way! These Onkyo TX-RZs are THE best A/V deal out there. Also, you could have chosen to run 5.1.4, and retained your overhead speakers- it’s only while running 7 ear-level channels or dedicating 2 (of the 9) channels for a second zone, that you trade away the ability to have 4 overheads. Of course, as you correctly stated, you may supplement with an external 2-ch amplifier, and all atmos configurations will be available, including 7.1.4. Oddly, the external amp must be used to power the rears (speakers 6 & 7 of a 7.1 system)- it would be nice to have the option of running the front L & R speakers from a separate dedicated amp, leaving the less-demanding surround duties to the internal amps. In any case, I’m using an older 6.1 channel (yes!) Cambridge Audio AVR I bought in 2005 to run the rears (which in turn allows me to do 7.1.4). Because the Cambridge has direct analog RCA inputs for all six channels I’m also able to run my front LCRs with it! That way, the Onkyo doesn’t have to work very hard at all, and the Cambridge amp is much better sounding (and ultimately more powerful) than the Onkyo. A pretty good use of an otherwise “obsolete” piece of equipment, I think!

[@GOLDEN4122]

... I don't know if they have made improvement for the RZ series ... I have had one Onkyo Nr-747 7.2 ..Blew up the HDMI card twice , first one covered by warranty second time unfortunately need to pay for the repair .... I hot the RZ 730 last year and running 7.2.4 setup with a Emotiva 5715 external amp for front left/right , center and a rear surround ... Still I need a cooling fan on top of the RZ730 😅 ..But now the Onkyo 730 works cooler just a tab warm ... and I'm happy with the performance ...

[@omarseneriz5577]

I have the 830 also and is nearly identical to the 840. The 830 I pick up for $500 and the only difference is the 830 doesn’t have imax enhance other than that is the same. For the money is a great receiver.

[@omarseneriz5577]

The Fortnite Camper King I had no idea.. Thank You for the info I will look on their firmware site.

[@rhealdubreuil]

Did you get a chance to hook this up to your dedicated amps and use as just a processor? I would enjoy hearing your thoughts on it as a processor along with any future receivers with the available pre-outs. Also I notice in the specs that it is compatible with HDR10, Dolby vision etc but no mention of HDR10+. Do you know know if it is compatible with HDR10+? Keep up the great reviews.

[@StevetheTechBro]

Aren’t you able to run 4 height speakers if you run a 5.1.4 setup? It’s only an 9.2 channel receiver correct?

[@moretwocome21]

Yes, the TX-NR787 fully unlocks DTS:X® and Dolby Atmos® movie soundtracks with a 5.2.4-channel

[@TheFrugalAudiophile]

It would be interesting to see how this receiver stacks up to the new denon X3600. I know that receiver has nine channels of amplification, not sure if it has 11 channels of processing though.

[@keepingupwiththejones2933]

Denon 3600 can process 11 channels

[@deependrasagar6880]

Plz tell the 2channel driven power at 8ohms or 4ohms bcoz 250 watts 1 channel driven at 6ohms is inflated.

[@seanlacroix]

The 250 rating is accurate but not realistic as nobody runs they're system at 1khz and 1 channel driven.

[@craiglamb9029]

The actual full range 20hz-20khz Is 120w RMS @8ohm 2ch driven. I own the RZ830, same specs.

[@BigNickTx]

I envy you brother, keep up the nice content!

[@emilianoescobar1015]

Thanks for the review. I would like if you can make a follow up review for this unit working with the Xbox One X and Atmos games, so Onkyo acknowledges the 2019 AVR are not compatible with Atmos implementation from the X Box. Also, after the upgrade, HDCP for all HDMI ports were upgraded to v2.3. I would also point out, that using external amp to accomplish 7.1.4 wont allow to drive the Front Speakers through the external amp, only the Surround Backs.

[@Shaker4x4]

Still running a TX-NR818 Class AB. I note the harmonic distortion of these Class D receivers. Compared to some other class D amplifiers, these Onkyos still have another generation to go before I upgrade. I have plenty of solar power, so energy efficiency isn't an issue with the AB amp. I have also heard many complaints about the new auto room calibration, and personally find the older XT32 calibration fairly useless as well compared to by-ear calibration. See what Onkyo does next. The RZ models have bee running for a while now.

[@yatishwaranand6409]

I wish I had a theater like you

[@MrJpdw67]

Interesting - which would you rate more, the 840 or the marantz 6013...

[@therealshanelee]

840. Not a fan of Marantz.

[@MrJpdw67]

@@therealshanelee thank you for getting back to me. You have helped make my mind up - will be buying the 840 tomorrow....was holding off to hear your review. :)

[@tpoulet]

@@therealshanelee I have an Onkyo TX-RZ810 and had found a great deal on a Marantz 7013. What's your issue with Marantz? I've got Paradigm speakers. Any input would help to make a decision.

[@seanlacroix]

I had an rz830 and it was nice but I changed to a marantz sr7012 and I like it a lot better.

[@MrJpdw67]

@@seanlacroix from my understanding that model is the next one up from the 6013, and costs more. In the UK both the 804 and the 6013 are the same price, but the 804 has more power output.

[@gmpnj29]

Looks good. What is Sony privilege 4K ?

[@BIGLEMON23]

GREAT REVIEW

[@2Drezik]

at 5:01 actually no. it can handle 5.1.4 without any addition. you'll need pre out for 7.1.4

[@johnbuddenbohm]

I have the 830, Do you know how to turn off the eq?

[@azriazris]

How about thi receiver is that too hot or not?Same like Tx-nr hdmi chip problem?

[@chieff666]

what is the best setup you have or tested?

[@marxnicolaas]

I onw the Onkyo TX NR686 looking forward for upgrade to RZ840..

[@Enemji]

Why do I need all the 4k/8k processing?

[@soulcanx]

Hi there. I have a very short question: I have Onkyo tx nr1009 as you may know it has many codecs but Dolby Atmos. I am about to buy Klipsch 625FA. Can I utilize the Atmos top speakers on that with Onkyo nr1009? Would it be a good idea? Thanks for your reply in advance. Cheers.

[@trgr123]

Hello! does it support banana plugs?

[@therealshanelee]

Yes

[@MrTeeZee2]

Hey Spare I got dizzy from the speed...LOL

[@emilianoescobar1015]

Shane, can you ask Onkyo to let 840 owners to upgrade to Dirac for a cost? 840 has the same hardware as RZ50 so it should be doable :)

[@in2flying]

So def considering this receiver! However because my equipment will be 30 feet away from the actual room, what is your suggestion on the calibration mic not being long enough? Great video!

[@therealshanelee]

You'll need an extension.

[@in2flying]

@@therealshanelee Thank you for the quick reply. Does Onkyo or you have any videos on performing the calibration?. The task seems daunting to this newbie.

[@adanperez75471]

which one is better Marantz sr 6013 or this Onkyo?

[@odeooo16]

I'd go with the 6013

[@adanperez75471]

OK thanks

[@Grelleum]

I bought the 6013 and replaced it with the 840. I'm glad I did, it sounds better to me and runs much cooler.

[@adanperez75471]

what speakers are you using?

[@Grelleum]

@@adanperez75471 I have the Martin Logan 35xt with motion 8i center and 2i in the rear... just a 5.1 setup. My wife and I both found the Onkyo sounded better with these speakers in our home. The Onkyo is a larger chassis and about three pounds heavier, which means the power supply transformer is probably a bit bigger. I actually went through four receivers before settling in the 840... Marantz 5013 > Onkyo 830 > 6013 > 840. Both 5013 & 6013 run hot and there was noticible distortion during some passages when played loud. I could not play either Marantz loud.. They hurt my ears. At moderate levels they sounded very good... But both Onkyos put a smile on my face when I listen to them they are just better sounding in a way I can't describe. Also when I play the Onkyo at very loud volume it doesn't sound like it's too loud, meaning it doesn't hurt the ears, if that makes sense. The 830 sounded awesome but I had some HDMI annoyances with it. If you have the available credit I suggest buying both and trying then in your home with your speakers.

[@derickhenshaw3839]

Whats a really good mid level AV receiver

[@vincegutierrez3780]

Like my rz840 with my klipsch speakers but I’m not getting ATMOS label through my Xbox 1x .

[@MALICIOUS330]

Onkyo has confirmed it’s broken on 2019 receivers as of now.

[@petecfla]

@@MALICIOUS330 its the X-Box that is the problem, they are not using the updated spec as confirmed by Onkyo.

[@petecfla]

its the X-Box that is the problem, they are not using the updated spec as confirmed by Onkyo.

[@MALICIOUS330]

Peter Chicchetti My Onkyo TX-RZ830 has no problems with Atmos on the Xbox. Like I said it’s the 840 that needs a firmware update. The Xbox codec is not the problem. 🤷‍♂️🙄

[@jimmy2shoes75]

My front stage consists of klipsch speakers RP. Does the rz840 pair well the klipsch, I worried that they may be too bright. Also can you use room correction and the Equalizer at the same time

[@wjwhite90wjwhite67]

How about Onkyo last time hdmi problematic no sound

[@Dizzle406]

Great video as always thank you! Did you by chance do a video on the 920? That’s the one I currently have and would love to see that video.

[@douglaspaz3292]

I had same model tx rz920 , which configuration u have in crossover ?

[@Dizzle406]

Douglas Paz I have it set at 80hz for my mains and surrounds. I have it set at 100hz for my surround backs.

[@joseismelreyes3879]

I have same reaciver onkyo TX-RZ920 7.2.4 configuration. for me my front towers in 40hz but i not understand in full band it's more better sound in my room... center chanel, atmos, surround and surround back i have in 80hz sound is amazing....

[@douglaspaz3292]

@@joseismelreyes3879 que tipo de subwofer tienes ?

[@frederickwilliams3319]

Hello. I know this is an old video, but I just found it. I have a question about sound quality and amplifier section, comparing Onkyo, Denon and Marantz. When comparing similarly priced receivers from all three, which do you feel has better sound quality and which seems to have better amp sections? Also, now that Onkyo/Pioneer/Integra has Dirac, how much of an edge (if any) does this give them in sounding better than similarly priced competitors that don’t have Dirac? I’m trying to decide what to buy on a $1500 - $2000 budget and want the best sound quality I can get for that price range. Thank you for your help.

[@PeterGalbraith]

Came here to look it over it over. US$999 when it came out 2 years ago? Why is it on super boxing sale for about the same price (C$1300) now in December 2021?

[@iyyappansmi3482]

How many price for indian money value?

[@SINGHIRENA]

IS IT E ARCA ?

[@cellfactor100user4]

Got a Denon X4500H with 2x Klipsch SPL-150 and 2 Klipsch RP-8000Fs. I love the quality and everything. BUT. I am aiming for a 7.2.4 dolby atmos system. I was thinking to get an external amp since my denon can't process 11 channels. If I pair my AVR with this Onkyo receiver, will I be getting the THX cinema experience as well? and if not, how could I connect my 7.2.4 system in a way that I got both atmos and THX? Thanks in advance!

[@gtric1466]

Great review, i have it's older brother the NR-797 Run the Accu EQ just so i can turn on the double Bass. then I only use the manual EQ. for under 200hZ. also there is a separate EQ setting for the sub woofer which is nice. run everything THX except my fronts which are set to full range. i have Zu DW's so there very efficient and dynamic. Love the Onkyo sound especially for 2 channel. mine is Class A/B i believe the RZ models are Class D but I'm not sure.

[@TheGarvito]

how big is your theater?

[@Angel-AbC9]

My shop list is between yamaha 2080 Denon x4500h or marantz sr6013

[@tlathbury8941]

Thanks for the review ! Any chance you will be reviewing the GoldenEar Supercinema 3d Array XL ?

[@clsosa74]

I haven’t upgraded my 5.1 set up in years. What AV Receiver would you recommend as my set up is only for my living room? I currently use Definitive Technology ProMonitor 800 bookshelf speakers with a golden ear technology force field 5 sub. My current receiver is a Yamaha RX-V1800 (very old but have never had issues). I will upgrade my speakers later and would like to use 7.1.4. Would like a mid to high tier model.

[@therealshanelee]

This Onkyo is great or If this is in your budget it's a higher end receiver with one of the best room correction systems available. bit.ly/2R3p23F

[@derrickgarcia303]

How would you compare that to Integra? Thanks

[@therealshanelee]

They are the same thing.

[@nathanlunsford7110]

You say for four height speakers you need external amplification. What about the processing of those extra two speakers? How do you make that work with this avr?

[@BeefyMon]

Nathan Lunsford it’s all internal, just make the correct settings, and the processor accounts for all channels, the internal amps power everything but the rears- which is where the external amp comes in.

[@fp9623]

@@BeefyMon and what is the external amp connected to? I mean, how does it get the sound for the height speakers? Forgive my ignorance, but I would really like to know how that works, maybe you can explain it to me

[@seanlacroix]

@@fp9623 there are amplifier pre-outs for all the channels. Then you just set it up in the menu system to run it the way you want.

[@BeefyMon]

Nathan Lunsford right. Basically, with the correct settings, all 7.1.4 channels are processed and sent to the pre-outs. Only 5.1.4 channels (that is everything except the rear channels, or I call them, “speakers 6&7”) are internally amplified. You must connect an external amp to amplify the remaining two channels. Why they chose to leave out those particular channels is a mystery to me- it seems like you’d want to make that selectable, and/or default to the front two channels which would help take a huge load off the system. You could do what I’ve done, used an older (but high quality) AVR with multichannel inputs rather than a 2 channel amp. Use two of the inputs for the rear channels as I’ve just described, and three of them for the front left, center, and right speakers.

[@nathanlunsford7110]

Matt Buckmaster ah I did not know this could process 11 channels despite being only able to power 9. Nice feature though

[@saturnoadin7411]

Hi!! How can I get the set up 9.2 Dolby Atmos in My onkyo receiver..????

[@immortanjoe6432]

5.2.4

[@Wallriss]

Would it be able to fo 5.1.4 instead

[@adsfghyy69]

I noticed in the menu for bass you had crossovers at 80hz and the lpf hpf at 120hz, I’ve asked about this the rule I remember hearing that your hpf needs to be approx 40hz above your crossover, is this correct

[@younghovajigga]

This or the Marantz SR6013?

[@therealshanelee]

This

[@younghovajigga]

Wow. Kinda surprised to hear that. Can you give me your reasons why? I’m adding 2 more speakers and want to upgrade my denon x2400h

[@joseismelreyes3879]

I ask, ¿in the crossover do you hear the front speakers in full band better??

[@jlaplaable]

first a good video thumbs up, I am considering buying the Denon AVR-X4500H, right now I have Yamaha Aventage RX-A1060 it is 3 years old. Regards Johnny

[@keepingupwiththejones2933]

Might want to consider the Denon 3600 as well.

[@jimmy2shoes75]

@@keepingupwiththejones2933 I agree, the ability to add separate power amp to the front stage and not be limiting it to heights only is a big seller

[@farlansangel]

We have a denon x2500h and very happy with it. Very user friendly UI and great sound.

[@CriPPleR_HD]

Anyone purchased this Onkyo 9 months ago and manage to still have it function? Has it been stable? Curious since my buddy’s unit stopped working and before that he was having HDMI issues. Wondering if it is just bad luck with his unit. Trying to investigate to help him decide to get it fix or purchase another brand.

[@YongDuHee-o8x]

tx-rz740 support for eARC? i'm buy yesterday

[@joeykitty2892]

No, it does not. Source: Onkyo website.

[@fadetoblack.-]

You're comparing a receiver to emotiva amplifiers and preamps? Of course it's going to seem lower midtear. Come on man at least compared it to a receiver. Let's do apples to apples. I love your videos very professionally put together but let's keep it real next time

[@kevfarny4082]

Will this unit do 7.2.2 ? The manual I seen says it can but I didn't see it on the menus..

[@balajay8921]

The manual says you can add 2 subwoofers but no such option seems to exist in the setup. Is it because there is no individual calibration of the subs? Any I tried connecting 2 subs but only 1 sub responds...

[@BlackEasterEgg]

can someone tell me what i need for externel amplification. i really dont know what to buy.

[@infinitree]

Wow, still no answer here. I'm a total noob to the audio realm, and I'm curious as well. I've been reading the FAQ on r/hometheater mainly.

[@carcar5911]

I have a question. I have an onkyo txrz820. I thought I could do 7.2.2 atmos. Turns out I can only do 5.2.2 atmos or 7.2. Should I return the upfiriring Dolby atmos speakers and do 7.2 or keep them and do 5.2.2 atmos. Do the upfiriring speakers really make that much of a difference? Please help!

[@joeykitty2892]

I would advise performing a comparison listening test. If you're satisfied with the 5.2.2 Atmos sound; keep them.

[@kevinrobertbrown2351]

Great review..I've always bought into the Onkyo brand..I have the TXRZ-810 Receiver from 2017..very nice receiver the 840.

[@video-carl]

Does this receiver support 5.1.4 without an external amp?

[@sneikiusas]

Yes

[@dreday1062000]

What would you recommend for someone who has $500 to spend on a Dolby atmos receiver? It’s not for a theater room, just a living room.

[@manuel0578]

Upgrading to this from NR636 😀

[@therealshanelee]

Nice 👍

[@gregrichard9192]

For that price I'll go with a marantz av receiver

[@MrViper7121]

Why you say that?

[@Angel-AbC9]

Please review yamaha 3080 or 2080

[@kevindavies5332]

But you can do 5.1.4?

[@BeefyMon]

Kevin Davies Yes, you can. It’s only because he was keeping all 7 lower channels in use, that he was limited to 2 overhead speakers (without supplementing with an external 2-ch amp).

[@kevindavies5332]

@@BeefyMon That's what I thought. Cheers

[@DarinBuss]

Hi, I was thinking about the onkyo also thinking about the new Denon Avr-3600 what are your thoughts please

[@therealshanelee]

Onkyo

[@DarinBuss]

SpareChange ty

[@reysualibio4804]

Onkyo is not durable denon 3600 is the model i look up

[@lexiewilkinson9703]

@@DarinBuss well go with the brother pionner!

[@Subacabra]

I've heard that particular model has an issue decoding atmos through Xbox

[@mikahl757]

My 5.2.2 Onkyo has no DTS-X or Atmos decoding issues with my Xbox via hardcopies or streaming but, this is the model I do want to upgrade to so I'm all ears to other's experience.

[@Subacabra]

@@mikahl757 on the Dolby Atmos for Gaming thread on AVS there is indeed some issue with the 840 and decoding atmos through Xbox. Check it out

[@mikahl757]

@@Subacabra copy that, Onkyo has a few 5.2.4 options I may just stick to upgrading to the older Onkyo TX-NR787 or TX-RZ630.

[@justincantrell09]

This is something i have heard as well, i just bought the TX-NR797 and does not decode Dolby Atoms for games. I am pissed.

[@petecfla]

its the X-Box that is the problem, they are not using the updated spec as confirmed by Onkyo.

[@timothymathetes]

very interesting

[@bluerainbug]

250W 6ohms 1ch driven???

[@povertime6381]

Don't forget at 10% THD.

[@astrotrance]

I want this thing! 🔊🎼🎶🎵🎹🎶🎶🎻🎶🎵😊

[@therealshanelee]

*IT'S ON SALE YOU CAN PICK UP THE ONKYO HERE* bit.ly/32VdNwM

[@seanlacroix]

You can get an 830 for cheaper and the only difference is no imax enhanced.

[@keepingupwiththejones2933]

Got my 4k copy of Casino. Thanks again, Shane. Have a great weekend.

[@ross5506]

I just purchased open box for $699. It's on route.

[@therealshanelee]

@@ross5506 congrats! Let us know how you like it.

[@Angel-AbC9]

Spare change you have a good following because your work you do is really good however i realise you hardly resonds to your fans questions..dont say u cant answer all because you rarely answer any. I checked ur other channels and its the same so i hope you can take 15 min of your time and reply to the help your followers.

[@cellenglish-canadianedu.le5938]

Lovely review. Well since 10 hears I how been using Yamaha rx-v550 till my sweet daughter broke it down. Sure that old model had lovely sound. Now I am ready to invest in. New one and I tried to find new rz900 but couldn't find it nowhere. I find your review tends Me to get the 840 but I m lost when you asked what is the shopping list. Sir if you are going to invest 1k in 1 box to get all those deciding options like atmos dtsx THX (lovely option) ND the option of iMax is not the important. Give me 3 Alternative options even older models to spend on. My range from 500 to 1k on an avr or Max 1k on avr with 2 atmos speakers. I do not mind older models at all I would appreciate your help

[@musicman8270]

Mine was dead out of the box, but it was only 850$. Might try again

[@seanlacroix]

It happens sometimes. All brands have a certain percentage that fail

[@musicman8270]

You can't fail if you never start. I am 50-50 on Onkyo, two Integras, one lasted till end of warranty, one fifteen years till I sold it. My trouble free 545 is five or so years old. But where else can you get a nine channel for this price? Probably try again, pay retail this time, a 150$ discount is a bit suspicious .

[@METALDKNO]

Funny all my onkyo amps have worked instantly and for many years.

[@musicman8270]

@@METALDKNO Yeah, My Integra 7.4 lasted fifteen years until I sold it, and it really sounded great, atop of the line receiver. But the HDMI 2.3 on the Denon might make me switch, have till tax time to find out

[@greebuh]

My review is on Amazon under "ME Willhite". It's a bad ass receiver.

[@THEFIREBOY901]

Can you review the Polk T Series speakers? I’m planning to have a home theater system on a budget with Atmos in my room because I don’t want to spend a ton of money on a home theater room with Klipsch speakers.

[@Davidarris1969]

ILL STICK WITH MY PIONEER VSX 933,AS ITS 7.1 OR 7.1.2 AND THE ONLY REAL DIFFERENCE IN SOUND IS THAT THE ONKYO IS T,H,X.😉💪💪✌👊

[@joeykitty2892]

...and it makes a difference in available sound choices; sound reproduction. I have replaced my Pioneer receivers with Onkyo, you can't beat THX!

[@alternativereviews]

Even this new design inside is better, its display screen still looks too narrow to us, isn't it.

[@reginaldnutter6613]

This is cute but you can never beat separates.

[@gsmd770]

I'll stick with my seperates! I guess if one is starting out that's ok? I was using a Pioneer with the class D amplification. Now that thing could rumble,but to be far it cost 1,500 Euro. Nice video for the beginners.

[@Shaker4x4]

I've been enjoying a TX-NR818 for years, not that I use it much. It has the updated HDMI board capacitors, but haven't yet placed passive heat sinks on the two hottest HDMI board processing chips. The RZ class-D series from Onkyo just doesn't encourage me to want class-D at all. It has high THD, and lack-lustre clear power. The old Onkyo Apps for Smartphones have always been garbage, and in my experience with Onkyo, including service, and repair, has been quite shit, and parts through one repairer only supplier. One of my kids crossed a surround channel speaker wire, and no circuit protection prevented an entire cascade failure of that class AB channel. I won't be buying another Onkyo until they are actually good. The competition brands are doing a LOT better. Denon... No way thanks!

[@coloniellizardt4191]

Looks nice but I still consider the Denon AVR-X3600H the best 7.1.4 Atmos/DTS:X receiver for almost around the same price as this, just only an hundred bucks more.

[@farlansangel]

Had a onkyo for a few months. Dolby atmos receiver. nothing but TROUBLE with hdmi and CEC issues with samsung qled. Drama! We swapped to a denon and worked in 5 mins and not have had any problems anymore and even better sound. Never buying a onkyo again

[@sudheeraziz1295]

How many Qatar reyals