OPV Nuova Simonelli Oscar II

This kit is available in our online store www.elektros.it

[@teresafunk8562]

I ordered the kit from Elektro, they are excellent to deal with. only took less than a week to come from Italy to Canada(ups) but was surprised ups charged me broker fee($16) on top of the shipping fee I already paid, this part is a bummer). Had my husband installed it tonight, super easy (according to him), and right the way, coffee tastes so much better(not so over extracted). I highly recommend getting it from Elektro if you are considering this extra modification. While you are there, get the pressure gauge, and a few extra upgrade, might as well if you are paying shipping and broker fee.

[@don1738]

For those who dont know why you would install an opv kit, it is to lower the bars of pressure the coffee is extracted. Generally rhe factory has the pressure to about 13 bars which is too high. I believe they have it this high possibly to save cost from the manufacturer. The opv lowers the brew prrssure significantly to the standard 9 bars or lower.

[@makeme.coffee]

Will it taste better or we're just following standards?

[@langzhi1873]

@@makeme.coffee the op got it a little bit wrong. The opv regulates the highest pressure of the brewing pressure, so if your opv set too high you might encounter issue with high extracting that could cause channeling in your puck, which is not great for your espresso extracting. So in short yes, it can help you extract better coffee

[@josealemany4525]

Just finished installing...I only get 8.5 bar. Per the pressure gauge I bought along with the OPV kit. Is there an adjustment to bring it up to 9.5?

[@randomaniafam]

the tube he started to undo at 2:25, anyone know where I can order? It bubbled due to the high pressure and heat and started to leak. Cant seem to find it anywhere

[@RosasusanaCandiaUgarte]

Porque no pasa agua al caldero

[@kostatko03ify]

I ordered this kit, but after I installed, machine doesn’t work right. A small amount of water flows from the head of the coffee machine. Does anyone know where the fault lies?

[@PerchEagle]

Wish you explained everything, I don't know what this is about.

[@moreno1636]

what improvements does the change bring?

[@checkwhatsleft4565]

Do you have the 0.5-0.6mm flow restriction for the Oscar ll?

[@VenenoSenzala]

When I connect the tube to the pump as shows @7:46 it is too tight and touches the copper line from the boiler. Did you connect the same tube or put on a longer one?

[@harijaja]

Hi! Just a question, I have an Oscar 2 and it has inside (right side when you open the machine from the top) a black box with a yellow cap that you can turn with + and - symbols. What is this? I've searched in the manual and it says nothing of its function! thanks in advance.

[@irodori--1960]

hi, you may have found the answer already, but here`s quick answer for your question! I think the box is a pressure stat, especially called `Sirai pressure stat` which is often used in commercial espresso machines. Pressure stat detects the pressure inside the boiler and if it is below its set pressure, it activates heater to heat up boiler until the pressure reaches its setting. When you remove the yellow cap, you will see a screw. By screwing it + or - ways, you can adjust its setting pressure. Hope this will help you!

[@ekosiswinardi1219]

Where i can buy opv kit?

[@zberzzz]

where is the sound?

[@risdiansah21]

What is opv?

[@mohammedshalash7842]

Kindly advise how to increase the coffee brewing temperature as the pressure switch screw is glued and cannot be turned,Thanks

[@ElektrosTolentino]

The pressurestat is blocked, but even if the adjustment screw can be turned, the temperature increase is irrelevant. The Oscar II (like other machines with HX) is at a good temperature after about 40 minutes it is turned on

[@mohammedshalash7842]

@@ElektrosTolentino Thanks

[@makeme.coffee]

@@ElektrosTolentino mine is ready to use after 10 minutes

[@bondarden]

Tell me please! What is the role of the jet that is installed right after the pump? Ref. num #07300860.

[@coffeesaurus]

Why did you use this OPV instead of OPV from Musica?

[@elektrosshoponline5417]

The OPV is the same one used in the Musica, there is no difference on the hardware

[@HARRIRISANDI]

Where i can get this? And how to adjust the pressure of this to 9.5 bar? Thanks

[@scottscottsdale7868]

Is it me or does this machine look a bit cheap? Plastic everywhere.

[@hariumardani4494]

sotoy