OrCAD Introduction - DC Circuit

[@36srinu]

Why the current is showing negative

[@RagaveshDhandapani]

Hi, thanks a lot for watching my channel. Please subscribe and share with your friends. I think you are referring to 14:07 current, isn't? Actually the voltage or current probe in OrCAD is always with respect to ground and i placed the marker on the current leaving terminal, hence it is showing negative. If you try same example and place the marker on the another end of resistor (within same branch), the current will show as positive. Cheers!

[@cobraeditz557]

nice teacher .

[@wcontrata]

Thanks -- Very helpful!

[@RagaveshDhandapani]

Welcome. Do subscribe and share

[@vkrs3315]

Thank you sir, you really helped me alot.

[@RagaveshDhandapani]

Welcome. Do subscribe and share

[@025-harshbindal7]

Thank u thank u thank u so much🙂

[@aminibrahim4362]

I have a problem where I don't have the Simulation tab on my software. how can I show it?

[@RagaveshDhandapani]

Hi Amin, You possibly created a Schematics, you must select as Analog/Digital/Mxsed design option to enable for simulation. Also, you the libraries available under pspice folder to draw the circuit, rest will not be included in simulaiton

[@celestynkuon4588]

THANK YOU! THANK YOU! GOOD MAN!

[@miziyak]

Explained well...

[@dharmpalgangwardharmpalgan4679]

Sar or cad ki baad Kun sa sufatweir hi jes me Leyot bnayia hi

[@RagaveshDhandapani]

It's orcad, old version. You may use new version, it's similar.

[@afiqahhhm45]

thank you very much sir

[@RagaveshDhandapani]

Welcome... do subscribe and share..

[@nikhitad8122]

u saved my life from my sir thank u soooooooo much

[@RagaveshDhandapani]

Welcome. Please share and subscribe to my channel. Do check other videos..

[@bhavanak1650]

Can we change the current from Milli ampere to ampere

[@RagaveshDhandapani]

Good question!! by the by, i never tried it. Just to it manually by adjusting the decimal points.

[@faridrizal2950]

How to add the bar below the tool bar?

[@RagaveshDhandapani]

There will be an option to add text block.

[@jack-wg9oz]

Thanks sir🙌

[@RagaveshDhandapani]

Welcome. Do subscribe and share

[@Mohammad-bg1xc]

Hey excuse me are you able to assist with s project?

[@RagaveshDhandapani]

Hi.. Sorry. I don't do that. Any specific doubts you can post here. Wish you all the best

[@Mohammad-bg1xc]

Thanks for the reply. Sir i just need you to review my lab report based on pspice orcad and correct any mistakes you face and i will pay you what you ask .

[@omarsalim123456]

can u give link for download orcard program

[@RagaveshDhandapani]

www.orcad.com/resources/orcad-downloads The demo version is more than enough to perform basic lab experiments. My new videos are made using demo version. You need to register and download.

[@nuthulasoujanya4556]

Tq u sir

[@muhammadshehbazaslam4549]

I have issue regarding circuit annotate in OrCad

[@RagaveshDhandapani]

You can click on text symbol in schematics view and marker followed by suitable option in plot view. Do share n subscribe ...

[@muhammadshehbazaslam4549]

@@RagaveshDhandapani I will share the issue. please email at [e-mail] Thanks

[@RagaveshDhandapani]

@@muhammadshehbazaslam4549 hi.. I have already mentioned the possible solution. I asked to share n subscribe to my channel

[@nanditagr2795]

How to install software

[@RagaveshDhandapani]

Please access their website. Register as student or faculty. You will be getting a demo version.

[@PravallikaBadana]

Can u share the software link to download in my pc

[@RagaveshDhandapani]

Recent version can be downloaded from www.orcad.com/orcad-free-trial Also, you can use falstad simulator www.falstad.com/circuit/ Do share.. subscribe and like the video.