THANK YOU!!! I was trying to get the motor out by prying the drive OFF with pry bars, but I was bending the sheild apron. This video showed me you have to HOLD THE MOTOR STILL and then unscrew the drive from up top!!
@tompem8 жыл бұрын
Thanks for bringing a 50 year old Osterizer back to life! Lots of memories with that machine making the world's thickest milkskakes.
@starladixon96564 жыл бұрын
Ikr
@starladixon96564 жыл бұрын
Lol and a lot more 😂😂😜😝😛💯💯💯💖💖💖
@RAU92319 жыл бұрын
My coupling on my Oster Blender broke and I had no idea how to get it off. Thanks to you its off and now time to order a new part Thank you very much!
@aribethtyr26202 жыл бұрын
Just earned a sub because you video was straight to the issue and not some crazy time grabbing scheme in order to game KZbin algorithms. Hope to fix this thing today, it isn't the same model, but it must be kind of the same process
@kirk89469 жыл бұрын
Informative. My 6 year old was fascinated with this video.
@trulyalay43084 жыл бұрын
*10 year old
@Blue_Dun2 жыл бұрын
Hello Adam. I know this video is 7 yrs old but I have this same blender,. Since the motor is fine, I decided just to repair with driver kit you illustrated. However, I'm having no luck getting the driver or, what some people call the stud, out of the blender. In your video you already have it out. I've tried holding the fan or the nut to the fan with a crescent wrench and turning the driver with pliers with my other hand. It won't budge so I'm wondering if I'm missing something? Thank you
@dolphinsil Жыл бұрын
Me too!
@lindalisko2417 Жыл бұрын
same thing with me!!@@dolphinsil
@shabrakhsh553624 күн бұрын
Same with me😢
@saulgodinezf4 жыл бұрын
Thank you so much for the video. It worked for me with some extra work because my fan blade started to get stripped so I ended up taking the fan off putting the nut back on halfway to protect the threads and grabbing the motor with a niddle nose vice grips and a crescent wrench on the other. Thank you again.
@markUTview3 жыл бұрын
I dropped a spoon into while the blender was running. Just ordered a replacement from Amazon. Amazon had some prime shipping, eBay cheaper but longer shipping. Thank you!
@autovale35955 жыл бұрын
Thanks, never imagined it was so easy to remove the impeller driver. I didn't need one, just needed to take the blender apart of put some oil on the bearings, screaming like a charm now. Thanks for posting.
@marksanchez4174 Жыл бұрын
Thanks, Andy! I have the EXACT machine you repaired.. do I don't expect a problem.
@AaronClow5 жыл бұрын
Thanks! My parts should be here tomorrow so will try this. We love the blender (it's not this model, just a basic pulse/on switch and HEAVY) and I wasn't looking forward to spending $$$ on a new one.
@Vankaner7 жыл бұрын
Thanks for putting the video on KZbin. It helps.
@יעלשחם-גפני8 жыл бұрын
Thank you! very helpful. Just finished fixing my blender according to your instructions.
@Stargazer194 Жыл бұрын
Thanks Adam, It's easier than I thought.
@acuamanotas7 жыл бұрын
Your video helped me repair my Oster blender. Thank you!
@Gluluman8 жыл бұрын
Same think happen yesterday, I knew I’d find the answer on youtube. Thanks AdamDIY great and clear explanations. A+
@sarahhardridge23922 жыл бұрын
Thank You so much... That's exactly what I needed to know 😁 and I love my reverse feature this Oster provides. It does amazing with my smoothies I drink daily! Mine is a new version but looks like the application will still work like a gem. Ii can't thank You enough!!
@MicBergsma6 жыл бұрын
Thank you, fixed my mom’s 😄🤙🏼
@lydiapenner9517 Жыл бұрын
Thanks a million! You helped me fix my blender, and just for $10 parts from Amazon. 🙂
@starladixon96564 жыл бұрын
Wow hey thanks 👍 I have an old school osterizer blender the coupling broke I thought I was done for...wow thanks 👍👍👏👏💕
@willlondon18243 жыл бұрын
Very helpful. Shared with someone on Amazon asking how to? Thanks
@adrianormsby54228 жыл бұрын
Thanks man, got back my blender back to work.. saved me from buying a new one..😊😊😊😊 mine was a bit old so I have to do some extra work but it's fixed now :) :) Thanks again.
@tgeliot3 жыл бұрын
Foo, my fan spun on the shaft, despite the shaft having a flat side, and the fan having a hole that (used to) have a flat side. I tightened the fan nut, but it just came loose again. I removed the nut and fan, and carefully put an adjustable wrench on the shaft. That allowed me to break the driver loose, but of course mushed the threads on the fan end of the shaft a bit. Some care in reinstalling the fan and nut sufficed to get it back together. Now to order a replacement driver . . .
@justincook548 жыл бұрын
The coupler on my Beehive was not broken but the square drive pin kept slipping out of the hole on the blade assembly. Maybe the bearings in the motor have worn and let the shaft sag a bit? Your video gave me the idea to shim the drive pin up with a washer between the coupler and drive pin. One less appliance in the landfill. Thanks!
@dbranyan90419 жыл бұрын
Thanks - just the information I needed. I ordered the part on ebay and should be back in business soon.
@RM-rj5ok Жыл бұрын
Thank you for this information!!
@meljane83394 ай бұрын
I just bought some plastic toy pliers. It looks like something like this might be great application for my new tools
@ProjectInfinito2 жыл бұрын
THANKS BRO!
@veterinarymedicine4874 жыл бұрын
Thank you man. Nice I'm fixing mine when get parts
@dianaalexander4558 Жыл бұрын
Wonderful.. thanks a whole lot
@fevenasefa62734 жыл бұрын
Thank you I have this kind of problem know I fixed
@drlarryc6 жыл бұрын
IF yours didn’t break completely off, but needs replaced (growling noise in my case) this may help you: The square drive stud simply unscrews counterclockwise out of the bushing allowing the plate to come off - I just held the nut (under the motor) securing the fan blade by hand while unscrewing the stud. Once the plate is removed then you can remove the motor from the plastic shell. To remove the bushing, I removed the fan blade and grasped the threaded end over the flat side with plyers while unscrewing the bushing with channel locks. ..not very hard to remove so I didn’t crush the threads too badly! The threads survived to reinstall the fan blade. NOTE: I tried to find an additional “jam nut” to tighten up against the first one to prevent the first nut from unscrewing, with a wrench on it, while removing the bushing. It is 1/4” but uncommon ‘threads per inch’ that neither Lowes nor Ace had (it is NOT 1/4x20 nor 1/4x28) guessing it’s a discontinued 1/4x32 on my 80’s or 90’s model. IF you can order an additional nut with your new parts, you will have the easiest removal - and you could just leave the additional “jam nut” in place...(No reason to remove the fan blade this way) Oh and don’t even try to grab the fan with plyers or it will easily begin to round the flat side off against the bolt when you attemp to unscrew the bushing - just way too thin to resist much force!
@hijjkkl9 жыл бұрын
your video is great....was ready to take my blender to a fix-it shop and pay $45 labor and $10 for the parts.
@barbaramahowald75554 жыл бұрын
Watched your video and I think I can do this! Great job on your video
@SpiritYogaDancer8 жыл бұрын
This is a great video! However, I'm stuck and I hope you can help. I have a 10 speed Oster blender and when I took out the three bottom screws, the motor did not release as it did for you. It is still firmly situated in the plastic housing. I don't see any additional interior screws. Do you have any ideas?
@leogoldberger94188 жыл бұрын
did you ever get the problem solved? If so, how? Leo Goldberger
@lindairvin19423 жыл бұрын
Same problem here
@semidor1 Жыл бұрын
Same here
@candelariaatalaya570911 ай бұрын
Your video is amazing, my blender is the oster pro 1200, do you think I can do it as you show in your video
@Frigenguy19 жыл бұрын
Just want to say thanks for the videos.
@AdamDIY9 жыл бұрын
You are welcome!
@efrasanti18529 жыл бұрын
Excellent video.
@weezyleo52774 ай бұрын
This helps alot ty
@matias29gdlmex5 жыл бұрын
Thank you so much for sharing your knowledge! It’s very helpful!
@DanielSmith-bv5fq8 ай бұрын
Not all Osters are the same, mine from the early 2000s was not serviceable and after messing with it for a few minutes I spiked it in the garbage can! 🏉
@conversationswithjv74743 жыл бұрын
This video is amazing but my blender is oster 1200, I bought it on December 2020 and the motors are attached… I can’t tell what screws I have to remove to get the motor out to change the driver. I was axle to open it but that’s it. Do you know how?
@nanapenn9 жыл бұрын
Thanks. Great video. Just what I needed.
@valladolid07115 жыл бұрын
Thank you for making this video sir!
@dickrowland12238 жыл бұрын
Hi there, very helpful. My oster blender fuse button seems to be stuck inside and won't go back to the normal out mode. Any solution ?
@carlosmanuelgonzalez3103 жыл бұрын
Thank you!!!
@malcori100 Жыл бұрын
Do you happen to know how the speed regulation works on these blenders? Mine has developed a fault where any of the speed buttons pressed give the same speed. Easy fix?
@pedrocortez1973 жыл бұрын
You rock my man! Thank you :)
@bhavyabhat12765 жыл бұрын
I’m trying to take off the old stud from the Oster blender but I’m not able to do it! If I hold the fan and rotate the stud with pliers, the nut from the fan loosens and falls down! I tried to open the fan and hold the shaft, but isn’t working either! Any suggestions please?
@khryslys Жыл бұрын
I’m having the sabe problem. We’re you able to fix it?
@mserrato5875 жыл бұрын
Thank you 🙏
@AdmNaismith5 жыл бұрын
Awesome- thank you for this. It's just the info I needed.
@lynnbennett68483 жыл бұрын
I will not buy an Oster again. Treated mine like a baby. No ice, only fluids and fruits and veggies. 3 months in and I can barely get it to chop up almond milk and fresh fruit. The power is there, but the blades aren't spinning? Neighbors getting irritated.
@Adeline94184 жыл бұрын
Glad I bought the cheapest Oster made. That way if and when it breaks I'll buy a new one!!
@sirgraves9504 жыл бұрын
However, with this premise you are throwing blenders into landfills fairly often.
@robertleyva9883 жыл бұрын
It would have been a good idea to clean off that rubber powder and also put a few drops of oil on the 2 bushings.
@kathyloveless94718 жыл бұрын
Thanks so much for this info.
@atvridingtrail2 жыл бұрын
Merci mec👍
@Minding11112 жыл бұрын
I’m going to try to fix mine
@ramrzboyz85074 жыл бұрын
The driver won’t come off, I’m holding the blade and it just unsrews off of the machine.
@What-cz3qq4 жыл бұрын
Had the same, got it solved by turning the blade around (this way the blade gets stuck with the frame) and tighten it real strong
@semidor1 Жыл бұрын
Can’t release the motor Got the kit Unscrewed various parts. Won’t release
@JavierArellano8 жыл бұрын
thank you!
@omarshariff8817 Жыл бұрын
How long did it last?
@sulemanb38866 жыл бұрын
i can't get out srews.with skewrewdriver
@lalkumara65542 жыл бұрын
By mistake I turned the blender switch button anticlockwise over the off position while it was working after that it doesn't work. please let me know what it may happend
@diyag6922 Жыл бұрын
How do you know that it’s driver causing the problem
@shabrakhsh553624 күн бұрын
How can I open the driver ? Mine is stucked or jamed there .
@meziembamara400410 ай бұрын
What about fixing *broken thread on motor screw* ? 😢
@jesusivanperezmejia67536 жыл бұрын
Thank you Adam. Excellent video, short sweet and hits the spot. Thank you so much. Now I{m off to the parts store with renewed self confidence.
@Stev607aqr8 жыл бұрын
Can't get the old part off my Beehive blender. When I hold the fan the nut holding the fan loosens. Any suggestions? Thanks.
@AdamDIY8 жыл бұрын
You can take the fan off and vicegrip the threaded shaft. you may ruin the threads but as a last resort, I would try it.
@bellalu14997 жыл бұрын
Stev607aqr Remove the plastic bottom from the base of the blender. Holding the center of the fan, grip the knob with a wrench and twist it counterclockwise.
@charlamiller39006 жыл бұрын
Stev607aqr , i have the same problem; when I hold the fan at the bottom, and use a pair of pliers at the top and turn counter clockwise = the nut and then the washer or spacer or whatever that silver ring is, comes off!! My Osterizer blender is about 30 - 35 years old, "Designer, Dual Range" I can't find any site that even recognizes this model. Anyway, did you ever find out how to get the motor out?
@cogniterra5 жыл бұрын
Will this work even for a vintage 1950 Oster blender with the same problem?
@squirrelsflame68295 жыл бұрын
I fixed mine this same way..it is an old one too, maybe not 1950 but for sure 70's
5 жыл бұрын
What about the stud? If its rusted?
@slhlj4 жыл бұрын
How do you put the cord back in?
@ShadowXak47SDX47 жыл бұрын
What if your blender got soaked in water or such?
@felixagbenorto98018 ай бұрын
I want the glass to buy or be replaced . Mine is fell and broke . I will buy it. The machine works perfectly but it just glass which broken.
@shwetatiwari96158 жыл бұрын
Hi Adam. Thanks for the video and it's quite knowledgeable and quite easy tutorial to understand. Thanks a lot. I want to know that how to fix a oster chopper that is not spinning. The blender is spinning but the chopper rotator is not spinning neither the blades. please help
@semidor1 Жыл бұрын
Can’t release the motor- Taking out various screws. Won’t release :/
@pmlopez04068 жыл бұрын
How cud I order that driver you're installing. I had the same problem with my Oster blender
@SAJJADHUSSAIN-mv8of3 жыл бұрын
Sir i need this part can tell me iam buy this material
@shubhsingh63904 жыл бұрын
Please send me link where buy this part
@pabloandrescabezas28629 жыл бұрын
When this happen does the blender turn on at all? mine does not and i'm not sure if this is the right fix
@AdamDIY9 жыл бұрын
Pablo Andres Cabezas It should still spin the motor. You have a different problem with yours.
@augustrosepriv892.7 жыл бұрын
Every light is flashing on our Oster. What does that mean?
@malrajsrikanth19124 жыл бұрын
Iwant parts of blender in Hyderabad which area
@mirai15773 жыл бұрын
What do I do if I broke the lever
@leogoldberger94188 жыл бұрын
I am trying to replace the driver on my 12-speed Oster slightly different model from the one demonstrated in your video. After removing the 3 screws holding botom plastic cover, the motor unit does not come out. What may be holding it? Please advise! Thanks. Leo Goldberger
@AdamDIY8 жыл бұрын
Many times stickers are covering the screw holes. If not then I would check under the rubber feet.
@josafatxiuhcoatl27358 жыл бұрын
You don't need to take the motor out completely. If you can hold the fan like in the video and twist the drive pin counterclockwise it should come loose fairly easy.
@ramkripalbishunath82294 жыл бұрын
I remove the wires from circuit board. Problem is i forgot which red wire goes where.. help from any one?
@oatmilk44548 жыл бұрын
what model blender is tht ur fixing? is it the new oster 1200 pro?
@HENRYROCKS9119 жыл бұрын
great
@malrajsrikanth19124 жыл бұрын
I want jars of blender in Hyderabad
@inolvidable. Жыл бұрын
You could have removed/cleaned all that black stuff around the driver.
@raptorclaw77 жыл бұрын
Do you just buy broken crap off of Craigslist and fix it for your YT fans?
@ramkripalbishunath82294 жыл бұрын
Ps. I had a burnt fuse. Thats fixed.
@geeharris51504 жыл бұрын
Where is the fuse located ?
@ramkripalbishunath82294 жыл бұрын
@@geeharris5150 close to where the power cord is inside the blender. Small white tube with metal caps. It fits in a u shape clamps
@julietspaghetti3 жыл бұрын
& what idiot designed it that the screws are 8 inches in