Oven Repair - Replacing the Temperature Sensor (Frigidaire Part # 316490001)

[@knucklehedjake6394]

Thank you. This was exactly what I needed to know and how to do it. I didn't need to splice it but if the connector didn't fit and I didn't know how to do it, it was good to include that info for people that don't.

[@crushedwrist]

The female end on mine that is attached to the wires from the oven is damaged. Do you know how I can get the new connector for the oven side?

[@chosenjuan1055]

What was the reason for splicing the wires instead of putting both wire connectors together?

[@amyschmidt1113]

My question too

[@southpawje]

The new sensor plug in connector didnt match the end coming out of the oven. So he cut the connector off the old sensor and put it on the new one

[@danielcraig8044]

Ok that make sense he didn’t explain that

[@Hesam0000]

Instead of changing plugs why not buy the probe with matching plug?

[@partselect]

Good question. The manufacturer has elected to supply only a limited number of replacement temperature sensor variations and therefore modifications to the harness connector may be required. The specifications of the sensor are typically the same for thousands off models, but the configuration of the connector varies from model to model for reasons unknown to us.

[@BrandonCockridge18]

@Michael Murphy ahahahahahahah

[@carlitozway2799]

Hi there Please provide the information where to buy the sensor ASAP THANK YOU

[@89081859838]

My oven floating temperature while baking and ruining all of my wife's baking. Any idea what could go wrong? Sincerely, thank you!

[@ushouldntjudgeme3683]

Exact same problem yesterday, wife not happy about her Christmas cookies. I have replaced the temperature probe awhile back and the baking element a couple years ago when it broke in two and stopped working. Any ideas?

[@jmhinkfuss]

Question: Does it matter which wire connects? The quick connect on my wire harness melted, so I will need to use ceramic wire connectors to connect the new sensor to the harness. Do the wires need to be connected (like hot and neutral on lights) or doesn't it matter? From the video, it looks like it doesn't matter but I want to be certain. Thanks for any help.

[@partselect]

The wires are not polarized so then can be interchanged. Using ceramic connectors are best for those connections.

[@gordonhepburn8053]

I have a belling double oven it keeps cutting out on the top oven bottom elliment. How do I find out if it's the working thermostat or the over temp stat its an intermitent fault

[@clintleming8072]

I changed the oven probe, it worked two weeks. Now, I am getting an error F14 on my Frigidaire model FPEF3081KFB. Any ideas? Thank you!!

[@wasimmanzoor7310]

My electricity goes off when I turn oven selector and suggestions plz?

[@BruceLawrance]

What tool do you use to tske off the back panel of the stove

[@robunderwood4763]

1/4" nut driver, 1/4" socket, or S01 square bit. MUCH EASIER to use the socket or nut driver

[@jiminutez]

Why didn’t you just replace the whole thing without splicing it?

[@JosephWeeks-u9y]

I was wondering the same

[@DwightStJohn-t7y]

An Ohm test on what you think is a bad part, first, and secondly why the re-wire job needed? should be plug and play with the correct part!!!

[@michaelwesten1764]

Hello, I have an older ge oven, model jbp76gs3ww. After a self clean the stove tops work, but the door is locked with no display lights and the oven no longer works. In searching online the thermostat fuse is the likely culprit but I'm having difficulty funding it. In taking off the upper back panel, the thermostat has a circuit board with components and a component that looks like a mini transformer with 2 fat 'winds' on it - but nothing that looks like a fuse. There's a 'connector/coupling' plastic splice thing that looks similar to what you replaced - but one wire goes to the oven light indicator and the other to the surface light indicator - so I'm guessing its just a connector for easy wiring etc. Do you have any other ideas as to where the thermostat fuse might be? There's many wires going in to under the stove tops, but I don't know if I can access that and raise the top with the door locked. Any help would be greatly appreciated. This model might involve replacing the whole thermostat circuit board or something, I don't know. Its a small brown circuit board with components - screwed to a larger green circuit board. Thanks for your time.

[@debbie970]

THANK YOU, THANK YOU, for this in depth information on how to get this job done because I was getting ready to run back to the store and tell them they gave me the wrong part because the connectors wasn't holding together. Thank you again!

[@abdultahir2127]

Question Where is timer my electric stove automatic off after 2 minute

[@davidaurelio2149]

my electric frigidaire oven is taking a long time to heat up what could be wrong

[@partselect]

Hi David, here's a link to our repair center page that should help you troubleshoot your oven's issues: www.partselect.com/Repair/Range-Stove-Oven/

[@kaymeadows5353]

Oven says F2 what does that mean

[@steelbak-customs]

Thank you very much! Fixed my problem.

[@austinbradley3411]

Question I had changed the heating element in the oven (cause some grease got on it a it broke the heating element) but my oven still wont come on will the temperature sensor fix my problem? I have an electric stove.

[@DrAmber2004]

Did that fix it? My heating element is working so I’m thinking it’s the censor for me.

[@robertbrittner6790]

WHY are you cutting the old connector off???

[@devondeputter8819]

Thank you so much! It worked.

[@carlagerlich7486]

I was able to replace the control board, and the cook top is working. However, the buttons that control the oven will not work.

[@partselect]

Hi Carla, What is your model number?

[@singerdanceractor]

My model number is FFEF3015LS I'm ready to take a sledge hammer to mine as it is constantly flashing F10 with the only way to get it to stop is pulling the whole oven out. It doesn't even get that hot as my food is always under cooked. Is it okay for me to just rip this annoying part out and leave it out.

[@partselect]

Hi, when researching the fault code F10 for your model, the manufacture suggests it could be the oven temperature sensor probe or the electronic control board. If you unplug the range and access the temperature sensor you can check the resistance of the sensor with an ohm meter. If the ohm meter reads 2500 ohms or higher, then you have a defective sensor causing the issue. If the sensor is okay i would then check the control board connection in the range.

[@shadowx089]

So how do you test if your oven is reaching the right temp? We have an oven for about 9 years now and it seems like its not reaching the right temp anymore. It cooks food but food seems to be taking a long longer to cook and trying to make brownies or other baked goods can be difficult to time if its not cooking at the right temp.

[@partselect]

There are oven temperature thermometers available from hardware stores and appliance retailers that you could try, although they may not be precise enough. Most electronic ranges using thermistor style temp sensors will have a self testing method available through the electronic control. What is your model number?

[@nutfield7678]

The temperature of my oven can be programed for an offset of +/- 35 degrees F. Check your owners manual.

[@briscojones3094]

Hi Steve I have a NEW frigidaire oven that keeps beeping showing F90 and dr what should I do to stop it? It won't allow my oven to bake anything

[@partselect]

What is your model number?

[@amhv35]

PartSelect 79074233310

[@eddiewu1990]

I have that exact same model and the exact same problem! what is that part called and where can i find one with the proper connector? thank you! video was helpful!

[@monssifnexus3744]

hey I have a question please my oven keep showing the F1 error is it the sensor or something else model number FES367ABG serial number NF34407354 THANK YOU

[@monssifnexus3744]

and how can I solve it is it the sensor

[@cholosoy8511]

Why don’t you guys sell a probe with a connector that actually matches 🤦‍♂️🤦‍♂️🤦‍♂️

[@jamesmccormick211]

This is terrible. Right at 1:06 when you're zeroing in on critical steps, the camera is too far away to see anything!

[@jamesmccormick211]

At 'locating the temp sensor' and shortly beyond, we cannot see what is happening.

[@stevenelson4235]

It would have been a god comment to add that "IF the connector doesn't fit this is how to remedy that." My 1st thought was "Why did you cut of the connector if the new one had one?"

[@ridagaceb7689]

Thank you so much my sir

[@nowannabeonthis8522]

he didn't actually connect the wires. he only stuck them in the plastic tube and crimped them. how exactly do wires that are not connected work?

[@ronalddmccall6154]

The connectors are metal and so it acts as the conductor between the 2 wires

[@BrandonCockridge18]

thanks my friend