P&O MPPT Explanation and Code in MATLAB/Simulink!

[@fellylombokonde3354]

Very helpful! Keep up the good work.

[@TheUrbanScholar]

Thank you!

[@udoyshourov1880]

Your videos are clear and easy to understand. Many many thanks. Can you please design a remote microgrid with wind-pv and diesel generator and demonstrate it? it would be a lot help. thank you.

[@paramoneyo8345]

i watched it and it helped me a lot for my project great explanation!

[@TheUrbanScholar]

Thank you so much! Do consider subscribing to our channel.

[@gastory7016]

This video helps me so much. Thank you

[@innovatorsinc.9057]

Great video, thank you!

[@saumyasingh2356]

This was very well explained and extremely helpful..Thank you! Can you please upload a video regarding inverter connected to PV using MPPT simulation..thanks.

[@TheUrbanScholar]

Yes we'll do it 👍 Stay tuned 😉

[@saumyasingh2356]

@@TheUrbanScholar Sure👍

[@vasavisai1890]

Please make a video on Implementing the control design from Simulink to DSP board (C2000)

[@carltonncube8349]

what is Vref...........and how does it change with change in duty cycle....................

[@rajhandique4399]

If 🔺️P>0 🔺️V>0 then duty cycle should increase

[@markov4119]

I thought I was crazy when I saw this, I even went to read books about it. when dP > 0 if dV > 0 then Vref = Vold + duty cycle else Vref = Vold - duty cycle. when dP < 0 if dV > 0 then Vref = Vold - duty cycle else Vref = Vold + duty cycle. Please correct me if I'm wrong. Thank you

[@erwandesfrichesdoria5717]

is it not possible to only focus on the current? The current drained can be lower or higher than the current at mpp. Then we just have to 2 if loops in which we check whether the current drained is lower or higher thant the current at mpp, and we adjust the duty cycle accoding to...

[@contehalimamy4872]

Hello bro could you please made a video on how to do the simulation on hot spot on PV modules performaces

[@arrmeilajeyanathan7318]

Great video! Really helpful :) How did you determine deltaD?

[@ankitnishad408]

Please correct your code in the second lop of voltage where VpV - Vprev

[@chaimach8942]

Which one please ghir me a answer

[@jeebannayak8449]

sir, at 1000 irradiation, power maintains constant but when irradiation changes to lower than 1000, power keep n deceasing. kindly reply sir.

[@TheUrbanScholar]

Yes, if the irradtion decreases then the power input to the panel decreases hence the power output decreases

[@Yaswanth]

At 3.47 how you taken vprev,pprev and deltaD values

[@TheUrbanScholar]

Delta D depends on the perturbation yoi want.

[@Yaswanth]

@@TheUrbanScholar can you share you telegram username so that I can contact you and clarify my doubts

[@dheerajahlawat14]

i am geting error not able to get MPPT bloick in simulk pls help as soon as possible.

[@vcaa7818]

Any document is available sir for using wind turbine mppt based p and O technique

[@westlorndarbygirim1647]

Can i simply put your code for the P&O algorithm on different PV system model ? Doest it works? Bcs i have problems to do the command

[@anishaagrawal6894]

Video is very helpful.I request u to make a video on incremental conductance as well. I m working on it nd get stuck in the code.Can u please help me in the code

[@TheUrbanScholar]

We'll come up with the incremental conductance video soon :)

[@usmanabdullah5321]

kindly explain Modified P&O (dp-P&O) algorithm also

[@rumman_huda]

2:04 duty cycle must increase. (I think you misread it and said decrease)

[@niyantachavda1361]

If I change the deltaD value to some other value (say 0.001) then duty cycle goes negative.. why so?

[@TheUrbanScholar]

It should never be -ve, I suggest you to check your model again

[@guywhoknows]

Is this FB tied or preset for load as I can't see priority.

[@muthukumarmeiyappan016]

what will be the DeltaD value for buck converter?

[@abdessalamtriche2729]

can u sed to me simulink file pls

[@deepakbhardwaj4018]

Thankyou

[@lasaint18]

how can I use this for a three-phase system

[@surisettytejashwini4650]

can you do driftfree p&o mppt

[@muhammadzakir304]

Well explained! I wondered to ask if you have done simulation of P&O for series-parallel combination of PVs in MATLAB. There we sometimes have a problem of algebraic loop error while connecting PVs in series-parallel combination specially with large number of PV modules. If you could have the answer for that and make a video a on that, I hope it'll be of great help to many people.

[@TheUrbanScholar]

Hey Zakir, hope you're doing well. In the previous video we show configuration of the PV panel block on simulink while doing mppt, you have to uncheck the algebraic look check box

[@jaiminpatel1576]

Can u send simulation of mppt video

[@newDAVIDnew]

Nice. Sound could be better, your mic clips so please turn it a bit down.

[@TheUrbanScholar]

Point noted! Thank you

[@TheUrbanScholar]

Your feedback is valuable to us!

[@roshanchitranshi9529]

DEAR SIR PLEASE SEND THE MATLAB CODES IF POSSIBLE

[@surisettytejashwini4650]

where does perturbation step size is given

[@innovatorsinc.9057]

As DeltaD

[@bhargava.buddana]

Sir pls paste code here

[@TheUrbanScholar]

Do mail us!