AAP bahut achha detail me videos banate ho I'm big fan
@goheljayesh89034 жыл бұрын
Good sar aap bahot achi tarah se jo samjate ho is ke liye sukriya...or sahi mahiti jis tarah se dikha te ho is k liye sukariya ..
@jitenkumarpradhan48563 жыл бұрын
Hissing sound is coming due to ground looping as u have given power from same source.Give separate 5v dc to bluetooth module to reduce hissing sound. U can use a old mobile charger circuit for the bluetooth module as separate 5v dc.
@drnkneelam694 жыл бұрын
सर, आपकी आवाज़ और समझाने का तरीका बहुत अच्छा है. आपने IC के पास पॉजिटिव और ग्राउंड पर 100 - 200 uf केपेसीटर लगाने का सजेसन दिया था. (वीडिओ टाइम 2:40 से 3:05) इसे भी प्रेक्टिकली बताते तो हम जैसे हॉबीस्ट नए लोगों को और ज्यादा फायदा होता।
@Ronakvaish5 жыл бұрын
Thanks bro me yhi video dhoodh rha tha bhut shiddat se . Thanks yaar 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
@shivanshmudiraj75262 жыл бұрын
Sir which battery to use to make a small Bluetooth speaker if connect the battery 3cell 12v battery it get turned off after 3-4secounds when the volume is turned up
@kamruzzamanislam56915 жыл бұрын
sir.. muje lagta he noise apke low qualitie bluetooth module se ah raha he
@RohitvishwakarmaEDITS3 жыл бұрын
👍 mai bhi use karta hu 3 bord 5.1 ke liye koi noise nahi hai
@TechnologyME-uj2zt2 жыл бұрын
Battery use karne se noise nahi aati
@mowglimowgli-hy9co Жыл бұрын
Yes Right Bro Isme Koi Bhi Bluetooth Module Lagado Ye Noise Hi Dega Agar Aap Is me Neckband Connect Kar doge toh koi noise nahi aayega 1000000000 percent
@bmamplifier9894 жыл бұрын
Namaskar sar bahut acchi video hai aapki bahut hi badhiya
@riktamdey11924 жыл бұрын
Sir ap bahut accha detail review dete hai
@pranabsutradhar83833 жыл бұрын
Dada, Main PAM 8403 IC Wala Amplifire Board Use Kiya hu, Mai is me 8 Ohom's,2.5Watt ka 4" Speaker Lagaya, Sound Quality Bohot Ach6a He, Aur Bohot hi Loud Sound He Isme.
@jaichirutkar90234 жыл бұрын
Bluetooth module aur amplifier module k bich me dc to dc isolator lagao noise chale jayega...... Common ground supply k wajha se wo nose aaraha hai
@RumblePirate4 жыл бұрын
Same problem i faced sir, noise/ hiss at even low or no volume unlike TPA 3110 which is comparatively quite even though both have similar distortion levels as per data sheet
@kanhaiyaupreti81854 жыл бұрын
Use separate powersupply for Bluetooth and Amplifier
@officialboss29132 жыл бұрын
Sir, yea jo noise hai , yei apki 12 v ki same supply se jo 5 v regulet ho ke aa raha hai, isi liye yea noise ho raha hai. Ap alag se 5 v dijiye BT ko koi noise nehi hoga. Try this.
@KaushalKumar-mw9hq5 жыл бұрын
Bohot achha explain Kiya....tqu sir
@founder76163 жыл бұрын
Nice video bro. I Love your all videos & there's lots of knowledge in your videos.❤️
@thegrandknowledge10263 жыл бұрын
NCS ke music kitne ghatiya hote h but apke video ache h❤️ keep it up
@rajureddy64335 жыл бұрын
Hiss sound ko stop karsakte hai, Bluetooth board and amplifier ek hi power se nahi chalani chahiye, Bluetooth amplifier Ko ek mobile charger ke saath chalaiye, hiss sound nahi ayega.
@WhatIThink5 жыл бұрын
No dears it's no....There is a hiss in this board even without connecting any type of input.
@rajureddy64335 жыл бұрын
@@WhatIThink no what you are telling is wrong . I've connected the same amplifier with bluetooth board with the same power for both the modules, then you will get hiss definatley
@WhatIThink5 жыл бұрын
I will re check and confirm .
@RumblePirate4 жыл бұрын
On my TPA 3110, they have attached same lm7905 IC for 5v supply..and it works fine with any distortion at all, don't know what the problem with this board is...
@mrjanuyt97744 жыл бұрын
Tpa 3110 d2 vs Pam8610 best amplifier for 10w 4ohm speaker
@induvishwakarma89623 жыл бұрын
Apne voltage regulator par kaun se value ke dono capacitor lagaye hai please bataiye please
@TrozenTPlayzZz4 жыл бұрын
Awesome board
@soumyadeepkarmakar57024 жыл бұрын
I used it but in battery & a 1000uf capacitor it doesn't creat noise
@unknowndimension58294 жыл бұрын
Sir kya PAM8610 board me volume potentiometer laga ke hiss noise hataya ja sakta hai...???
@WhatIThink4 жыл бұрын
Board me noise nahi hai...bluetooth board se aata hai...volume lagane se control me rahega.
@shubhamchauhan59573 жыл бұрын
Sir ye maximum 2 or 3 days tk shi rhta h Uske baad bhut jada heat hone lgta h Audio cut hone lg jaati h Mene km se km ise 11 ya 12 baar badl chuka hu But bekkar h Phle phle din bhut acha lgega Lekin sch m bekaar h 😥😥❤
@maxblade014 жыл бұрын
Maine bhi same configuration me Bluetooth speaker banaya tha (10 watt wale chote speakers ke sath) aur power ke liye buck converter use kiya tha 4x18650 (3.7v, around 8000mah capacity) battery k sath but jaise he bass notes aata tha mera speakers k ek fattttt ka noise aata tha aur system restart ho jata tha... aur fir kuch time bad amp he udd gaya
@WhatIThink4 жыл бұрын
Input voltage jyada rahi hogi ya fir load 4 ohm se kam ho gaya hogi
@srobh52924 жыл бұрын
Apke bahut vedio dekhe u r amazing. U r Indian electronic man with hi fi knowledge 💖u bro
@prachurkannojia42255 жыл бұрын
शानदार👍 सर कृपया op amp पर भी वीडियो बनाइए जिससे कई amplifier connect हो सके
@WhatIThink5 жыл бұрын
sure..
@adityadhanraj39025 жыл бұрын
Sir full range speaker pe koi video banaye ki kaha se kharide aur pricing and sound test too
@aashumishra9833 жыл бұрын
Bhaiya bohot sare log jo 12v transfermer less power supply bnate hi pf ,ziner diod bgera lgake kya ye Circuit 8610 work krega kyuki adaptor ya transfermer bohot mehenga aata hai isliye
@rahulviswakarma45695 жыл бұрын
Sir TPA3110 class d amplifier board ka details bataiye...wo kaisa board hai?
@ranjitbhatta12 жыл бұрын
Aapko noise ekdom nahi ayega agar blutooth ko alag se power supply denge to. Ek old mobile charger se BT ko power djiye , 4007 diode lagake 0.7 volt drop karke 4.3 volt dijiye BT ka life vi achha hoga BT ko 3.7 volt sufficient hote hai same power supply se dene se noise ata hai Aap check karo aur result batao
@100ozmagnet84 жыл бұрын
phli baat k wo subwoofer nhi hain..or na hi wo boofers hain..wo pure woofer stereo speakers hain ...but apka knowledge great ha...bss ya aik correction thi jo socha k kr do..
@deepayansahoo4 жыл бұрын
I have similar one one bluetooth module as shown in the video and the sound seemed bad so I discarded it. CSR chip based ones are very good but not available locally and generally they come with amplifiers.
@bibhutibhusanadash66822 жыл бұрын
Sir namaskar. Pam8610 ko 12v transfermar 3amp se chalaya or bluetooth module ko 3.7v lithium ion battery se par bluetooth module excess hit kyu hai.please guide me kindly
@vk9123993 жыл бұрын
Best review Mene pam8403 se bt speaker banaya but wo radio ki tarah bajta hai no bass 😂😂😂
@kamleshkunvariya1205 жыл бұрын
Sirji board is excellent . Output is very good with bass. But treble is little bit poor over all value for money.
@WhatIThink5 жыл бұрын
Correct
@chhotuyt7849 Жыл бұрын
Kya agar 5.1 home theater 2050 ic wale kit me two subwoofer 5.25 ya 6 inc ka subwoofer laga sakte hai
@aashumishra9833 жыл бұрын
Bh.. Kya hum isko 500ml Ampere se chla sakte hai 12v 500ml Ampere
@somnathaudioelectronics60273 жыл бұрын
Sir ye same 2 pc 3inch 4ohms 10 watt ka speaker chalane ke liye 12 volt ...kitni ampere ka SMPS lagana hai .......?????? Please
@narendramankame79672 жыл бұрын
Sir. My 6810 module. When i connect power to the module No sound. but when i short switch mode sound comesout for the few seconds again goes to off mode. Can u suggest me why it is happning.?
@Coolmomdad5 жыл бұрын
Bro muje ek sound bar bnama hai to ek video banao us par jisme fm / card/ or usb and full remote control ho
@Shelby213785 жыл бұрын
Sir , I bought lm3886 sterio board from bagood but as soon as I hook it up it blew up and one of the two ic burst within half a second . I used 24 0 24 dual transformer what could be the reason ?
@WhatIThink5 жыл бұрын
Sorry to hear
@yagneshpatel11834 жыл бұрын
@@WhatIThink work fine with 24 - 0 -24 replace ic and try again or board is made wrong .
@lol_kumar-_-3 жыл бұрын
Sir ....mujhe lagta hai yea hissing noise yea saste wali bluetooth board ka hai warna smps power supply k lia hai .... aap direct mobile se aux cable ki saath connect krke dekhea Ekbar...
@sunilchristo95702 жыл бұрын
Powerfull.bord. Hai
@yogeshsinghsonigra40544 жыл бұрын
Noise ground loop ki wajah se hai bluetooth module ki supply 5 volt alag se do noise nahi aayegi
@riktamdey11924 жыл бұрын
Sir ap pam8610 ka humming problem Ko dur karna sikhaye
@WhatIThink4 жыл бұрын
Use separate power supply for BT and 8610. Then there will be no noise
@deeprajshakya7622Ай бұрын
Sir 6ohms ke speaker ke load pr kitna voltage supply dena chahiye ??
@anjuchoudhary622710 ай бұрын
@WhatIThink i am making a project and having problem, i have a pam 8610 connected to 20watt 4ohm + 10watt 4ohm speakers in series on both channels so 8ohm per channel and power supply as 3x 18650 batteries, input from 5v Bluetooth module which gets power from a 7805 regulator , i have also added capacitors between battery and amplifier of 4700uf+1000uf and a 22k resistor on sound output from Bluetooth module to reduce distortion but it still has a lot of distortion and clipping and most song are not even listenable and a voltage drop of 0.2-0.4v while running plus the chip runs hot even having heatsink on top, pls help i am stuck
@ashaychoudhary46435 жыл бұрын
Hello, I recently used an online calculator to calculate the crossover circuit coil. Which I made out of 23 awg wire 1" height and 7layers of 40 turns. To get appx 900 mh. When i tested the resistance it was 2ohms on each coil. I installed the circuit on my 4 ohm hi and low drivers and now the overall impedance is 16 ohms. I am using a dual 4440 ic amplifier. Can you please suggest me where I went wrong or is that normal that after installing crossover the impedance increases?
@WhatIThink5 жыл бұрын
Use thicker wires to make passive cross over...May be the wires which you are using to connect the amp to speaker are too long and cause of extra resistance ..Connect cross over direct to speaker then chek the impedance
@WhatIThink5 жыл бұрын
Better to use active crossover instead of passive.
@ashaychoudhary46435 жыл бұрын
I will check as directed and will update you. I am using 2x4440 and one tda203 amp to make a 5.1 home theater system. But the output is not what I am expecting. I would love to share the pictures. I am using 3amp 12 volt transformer om 4440 and 15-0-15 1.5 amp on 2030. Also I modified one normal vocal woofer to accommodate a subwoofer coil. And have connected 2x8 ohms in series to make it lesser impedance. One last thing. Thank you so mich sir for all the valuable information you shared. I have never seen any KZbin channel as organized and well presented on electronics. I am an electronic enthusiast and have learned these some on my own and some from teachers like you.
@yashshrivastava95272 жыл бұрын
Power supply is of 12 volt. Full range speakers are of 4 inches 30 watt each connected . Still voice is cracking at volume above 60 percent. Any idea
@SikandarKhan-ii2bc3 жыл бұрын
Pam 8610 pr perfact power suplly kitne voltt deni chyee kiya liptop wale charger laga sakty hen
@ashaychoudhary46435 жыл бұрын
Please make a video on passive crossover circuit as well
@samratbiswas35383 жыл бұрын
10+10watt Best Amplifier video
@prathmeshghodke48725 жыл бұрын
Noise suppression pe techniques chaiye ...
@rutvikkamble79023 жыл бұрын
mare cheap volume high carne par cheap power low hoti hai what do work
@yourajbadgujar78374 жыл бұрын
is board ke noise reduction kaise hoga. board me noise hai ya power supply me.
@WhatIThink4 жыл бұрын
input par volume control use kijiye.
@shashibhushan92953 жыл бұрын
Sir is amplifier ko 12 volt transformer se chala sakta hu..? Agr chal sakta h to kitne amp ka transformer lagana best hoga plz reply.....🙏
@WhatIThink3 жыл бұрын
12 volt 1.5 amp
@ShakilKhan-ij4gp4 жыл бұрын
Sir, 50+50 watt k liye kon sa D class amplifier board liya jaye. Pls tell me.
@WhatIThink4 жыл бұрын
3116 ka video hai ...dekhiye
@coldtech49104 жыл бұрын
The noise is because of ground loop problem as the the Bluetooth board is sharing the same ground ! Try with different supply for Bluetooth module !
@furious-choehaalen15253 жыл бұрын
Yes correct i fixed this prob
@amitghosh6966 Жыл бұрын
It will need a 12 Volt 2-3 Ampere smps adapter to work properly and transformer can be avoided as it's output voltage is high in many brands
@manojthatipigari8176 Жыл бұрын
I connected 12v and 1.5 amps its heating i donno whether its heating because of low input power or high input power
@amitghosh6966 Жыл бұрын
@@manojthatipigari8176 try using 8 ohms speakers
@manojthatipigari8176 Жыл бұрын
@@amitghosh6966 I used 8ohm speakers only.. Input bias rated at 3amps in one website.
@amitghosh6966 Жыл бұрын
@@manojthatipigari8176 If it's heating you may have to use a heatsink for the Ic if you're using it on maximum volume & also if there's Distortion in sound at higher volume then also Ic gets more hot so check these things
@abhishekgahlawat24764 жыл бұрын
ye bt module ki noice h aux conect karke dekheiye
@RideLikeAPro5 жыл бұрын
Sahi baat hai...bhai ji sahi baat karte ho app lo ek LIKE hamare taraf se👍 nice video..
@Vijaykumargupta11225 жыл бұрын
Bhai meine 4" inch ka subwoofer use kia lekin bas 30 min tak woo full volume pe baja uske baad apne aap band ho gaya . please tell me why
@infoandroid67924 жыл бұрын
Maine amplifier ki amp waire Ko hatho se kuch der pakde Raha uske bad band hua board chalu hai amp gayab ic khatam sayad ( ground - )amp waire se conect hone se hota ab se volume preset nai laga k dekhna padega
@thesoundmaster.2 жыл бұрын
Sound quality kesi milega 2inc 10w speakers pe 12v pe on this board pls reply
@sandeepdubey15554 жыл бұрын
Sir is board me 3 inch ka dono speaker lagaye ya 4 inch ka ...Kaun better rahega
@WhatIThink4 жыл бұрын
Dono acche chalange ...Jo bhi available ho lagaiye...
@hardnachopuppy3 жыл бұрын
Sir the noise is caused because the gnd is not isolated between Bluetooth module and amplifier ic
@hardnachopuppy3 жыл бұрын
kzbin.info/www/bejne/pJDFkGN4jLVjo6s
@praveenbanarase30522 жыл бұрын
Sir, 3110 aur 8610 me kounsa achcha hai....2inch ya 3inch speaker ke liye...strong and quality sound chahiye 🙏
@kunaladdan23362 жыл бұрын
Sir please reply 🙏🙏🙏🙏 Mere pas ek speaker ha jo 4ohm ka 8inch uska face ha or 3inch ka uska magnet ha mujhe nahi pata ha ki vo kittne watt ka ha kya me us single speaker ko es board me laga sakta hu please sahi information dena taki koi board ya speaker jal na jaye please 🥺
@WhatIThink2 жыл бұрын
Is board ke saath koi speaker nahi jalega
@charleslewis83463 жыл бұрын
vai jan me Bangladesh se apki video dekhtihey ismey 12 volt kitna amp use karcakti hey
@WhatIThink3 жыл бұрын
2 amp
@deepayansahoo4 жыл бұрын
I think the sound box you are using is of 4 or 6 Ohm, will they harm the amo as it is recomended to drive 8 Ohm? and in such low Ohm load the sounds seems okay with no clipping. here what to do to prevent clipping?
@Mazeezurrahman3 жыл бұрын
Hello sir First of all let me tell you will explain in details and in simple language that's makes your video interesting I want to connect three PAM8610 BOARDs with optical to 5.1 audio rush output as input to PAM8610 BOARD and its 6 channels speaker to my hometheater input . Is there any chances of burn PAM8610 ic or it will be safe my hometheater is having 2050 ic 7 in no 2 for subwoofer and another 5 ic for each channel. Can we use PAM8610 board as pre amplifier. Please reply sir... Thanking you sir Mohammed Azeez Ur Rahman. Sir please reply sir
@WhatIThink3 жыл бұрын
You can connect three 8610 boards with 5.1 decoder without any problem and use speakers on the output of 8610. But Do not use class d amplifier as preamplifier as switching frequency is mixed with audio signal and it will create heat in the next amplifier connected with this.
@pranabsutradhar83833 жыл бұрын
Dada, TDA 2050 IC wala Amplifire me Kitna Ohm's, Kitna Watt's ke Speaker Best Hoga? Agar Is Amplifire Ko 12-0-12 Volt's ki Tranformer se Chalau to.Aur Transformer Kitna Ampere ki Used Karu?Aur Kitna Inchi Ka Speaker Used Karu?
@KaushalKumar-mw9hq5 жыл бұрын
Stereo type se kya mtlab hai plzzz tell
@WhatIThink5 жыл бұрын
Please elaborate more
@rajeshsharma-vt9yc4 жыл бұрын
Nahi ye Jo hissing sound hai ye Bluetooth chip ka hai Mai 6283 ke saath speaker banaya tha prantu jaise hi use mobile se connect ki jati hai hissing sound chalu ho jata hai to ye Bluetooth chip ka problem hai.
@Funny.Edits.26 Жыл бұрын
Sir ye bataye ki apne jab chote Wale speaker lagaya ta to wo 10 w ke te par oms kitne te
@bindaasworld21192 жыл бұрын
Mera 3 way speaker 4 inch hai 30- 210 watt ka 4ohm ka 2 speaker hai kon sa amplifier board use kare
@chinmaypal86672 жыл бұрын
Sir, mayne is board ko use kar ke ek Bluetooth panel ke sath ek Bluetooth speaker banaya tha. Iska sound quality la jabab he. Lekin ek big problem hai. Ye board chalte time fm signal ko ekdm destroy kar deta he. Isliye may Bluetooth panel ka fm nehi chala pa raha hu. 😢😢😢😢 or iske as pas me koi radio chal raha he. To usko signal vi lost ho jara he. Mujhe fm sunna bahut pasand hai. Please sir ho saketo is problem ko solve karne ki koi upay bata dijiye.. 😢😢😢😢😢😢😢😢😟😟😟😟😟😟
@souvikmondal85752 жыл бұрын
Sir yeh Bluetooth 3.0 mobile se connect nhi ho raha par laptop ke sath connect ho raha hai... problem samajh mai nhi aa raha plss help
@RajaKumar-ri6si Жыл бұрын
Sir 8w or 4ohm ka do speaker 8610 ke amplifier se chala sakte hai
@revantrawal80623 жыл бұрын
I have purchased this one plz solve the noise problem
@MrVascoBhai_1M2 жыл бұрын
Bhai hmm 12 - 0 - 12 2amp 12v transformer use Kar sakte h issme????
@pratikdubey22644 жыл бұрын
Sir aap isko bridge mode me convert kr sakte hain ky ..jaise 6283 board ko 15 k resistor se short kr ke bridge me chla skte hain .....
@onlyelectronics1993 жыл бұрын
Sir ek dout tha pam 8610 ya tpa 3110 kon sa best ai
@bhagwatiprsad46173 жыл бұрын
सर जी ये वोर्ड कहाँ मिलेगा कृप जरुर वतादैं मै आपका आभारी रहूँगा धन्यवाद🙏🙏🙏
@saptadipcreation95094 жыл бұрын
I made a Bluetooth speaker with 2 10,15 watts speakers with Pam 8610 board. But 10-12 volt current is coming to the right speaker point of the board.The right speaker is not ringing and the whole connection is being turned on & off, on & off automatically. The left point is right. Please tell the solution.🙏🙏
@WhatIThink4 жыл бұрын
Your board is probably gone. Please touch the PAM8610 if it is overheating.
@saptadipcreation95094 жыл бұрын
Yes, board bahat garam ho jarahay jab may R point connect karke chalarahahu to speaker me par par sound ke sath on off horahahay. But L point achhese bajrahahay.
@mohmedmogal33723 жыл бұрын
3watt 4ohm k 6 speaker chala sakte he
@WhatIThink3 жыл бұрын
Yes
@b.d.kumbhasana27794 жыл бұрын
क्या 8610 में vol बटन लगाया जा सकता है..?
@WhatIThink4 жыл бұрын
Yes
@anindabanerjee60284 жыл бұрын
Sir there was a ic numbered ht8696 please make a detailed video on it and also hot to connect car 4.0 bluetooth module with it.
@kadirdawar82864 жыл бұрын
AGAR HUM IS MIAN VOLUME LAGA KAR USE KARE TO KYA YE AAWAZ KAM HOSAKTI HAI KYA
@WhatIThink4 жыл бұрын
Yes
@totanpaltotanpal48173 жыл бұрын
aur 4700uf 25 v ka capacitor diode ke sath solding kardo, jo rectifying diode, ic ke aage se connect karna hai, dekhna performance beter milega
@kaifin97293 жыл бұрын
Pls suggest the best pair of speaker for this pam8610......🙏🙏
@deepaksahani14003 жыл бұрын
75 percent volume ke upar jaate hi automatic audio off ho ja raha hai board me led jal rahi hai how to fix please reply
@abhijeetbehera74483 жыл бұрын
Sufficient current na hone ke wajah se auto shutdown ho jata hai. Zada ampere wale power supply use karo.
@sukhboparai62665 жыл бұрын
Sir app ny simple bass treble kit duoble lgany k bary me bola tha plzz bo video jaldi upload kren sir plzz
@WhatIThink5 жыл бұрын
I am making...
@deepakkumarkumar71862 жыл бұрын
Bluetooth connect k bad Noice karta h kya ye sir???
@darkworld43663 жыл бұрын
Sir Maine bhi ye bord parches Kiya tha but ye 4om ke speaker ko nahi Chala pa raha tha lagbhag 30% volume ke baad bord band ho ja raha tha ky problem ho sakti hai ?? please reply
@nishtalashubrahmanyam14483 жыл бұрын
Then how can I amplify 15watt output? That means that have I to use separate amplispeaker for each channel?
@sebidsouza40292 жыл бұрын
Sir can u make video on XA9533 audio amplifier ic
@studiovlog36354 жыл бұрын
What is the solution for noise?? And power supply kitna amp ka rakhna hai???
@shivampatel52264 жыл бұрын
Which is better for 10w stereo pam8610 and TPA3110
@WhatIThink4 жыл бұрын
Both are good ,for 12 volt use 8610. For higher voltage use 3110
@Vaibhav-my4bd3 жыл бұрын
Sir input audio ka ground nikal do noise khatam hojayegi