Parkside li-ion battery pap20 a1 dead, charging issue | Lidl | How to fix

[@makeandfixathome]

Subscribe to Channel: kzbin.info

[@benjaminobengagyemang5586]

Thanks for sharing this. I have become worried because I have same problem with my Parkside battery and just don't know what to do. With this useful idea I am definitely going to bring it back to life. Thanks once again 🙏🙏🙏

[@makeandfixathome]

Pleasure is mine. Hope this help to fix your battery Regards

[@MrGodsking]

@@makeandfixathome hi I have some of these all new can you fix them I don't mind paying

[@vasosandrea3532]

Good job people can learn to fix thier thing and not get ripped off

[@makeandfixathome]

Thank you :)

[@vasilijnawratil1836]

Thanks Mate, the same problem with my battery! Thank You

[@makeandfixathome]

** I'm glad to help someone. Pleasure is mine.

[@orlatris96]

Please could you tell me what the problem is with my charger like yours. flashes the red and green led and does not charge the batteries. a hug, thank you

[@makeandfixathome]

Your charger probably is ok, the problem is with the battery. The voltage on the cells is too low so the charger can't charge your battery and shows red and green led errors. You can try to revive a drill li-ion battery kzbin.info/www/bejne/anqYp6KOnMiMbsU You need an extra battery : if this doesn't help You have an internal problem. In my case, one cell was not soldered properly. Hope this will help Regards

[@djjaskolmechanik3509]

Well done :) What is the value of the thermistor in the battery?

[@makeandfixathome]

Thx, I have to check, if I find a schematic I let you know!

[@makeandfixathome]

hello there, it's difficult to find a schematic, but I just check resistance it is an 8.5Kohm, hope this helps.

[@djjaskolmechanik3509]

@@makeandfixathome Thanks You very much

[@makeandfixathome]

@@djjaskolmechanik3509 no problem, anytime mate !

[@makeandfixathome]

@@djjaskolmechanik3509 type NTC - when temp goes up, resistance going down.

[@cmh-re]

I have a pack that wont charge on his charger but works fine in the tools. cells are all balanced, all soldered correctly but still give this strange error

[@makeandfixathome]

(Two blinking led) error mean voltages on some of the cells is too low. Also, you can try revive kzbin.info/www/bejne/anqYp6KOnMiMbsU if you have an extra battery

[@GoogleUser-yj1wy]

I just bought a grinder a month back and after 2 weeks one battery not charging, a week later the second one gave up, same dual lights flashing at the charger

[@makeandfixathome]

some of that battery cell is Undervoltage, You can try this kzbin.info/www/bejne/anqYp6KOnMiMbsU

[@makeandfixathome]

good battery to broken battery + to + - to - for 15 -20 s and check

[@Subgunman]

Any idea what the amp rating on the fuse might be?

[@makeandfixathome]

It is very difficult to find a diagram for the Parkside battery. Maybe I'm wrong, but this fuse is not typical, in my opinion, it is a Current Sense Resistor. I have to find out. Some people place standard car fuse around 30A but ... I'm not sure this is a good idea. Regards

[@shaqlawa]

Hi, what does it mean when the battery charger parkside lights up red?

[@makeandfixathome]

this means your battery is on a charging when the finish goes for green

[@SiskinOnUTube]

I'm not a fan of the batteries. I've had two that drain the cells unevenly, so one will die i.e 0v.

[@makeandfixathome]

I'm with you my friend, this is just batteries. In this case, this was a factory issue. It all depends on how often U used them and charge. The cable is cable but in some places, You will need Battery :) Regards My Friend

[@damirivancic4964]

what is this charger output voltage? on what pins?

[@makeandfixathome]

*hi there charger output is a 21,5V 2.4A, but on the pins, have no voltage. the charger starts when you place the battery into the charger. So if you use a standard multimeter DC does not show you anything.*

[@damirivancic4964]

@@makeandfixathome multimeter show me on one pin 2.6v on onother in the midle 4.and something

[@MrSmazol]

@@damirivancic4964 what is a setting in multimeter ? AC ? I think, you Should check DC. On AC I have similar readings. If iam correct charging voltage will start, when battery sitting in. Regards

[@fabientuizat1129]

thank you !! what is the ref for the IC please

[@toudizdobywcaa2810]

Dzień dobry ile taka nowa bateria może chodzić czasu na pełnej mocy ?

[@makeandfixathome]

W zależności od urządzenia, do którego jest podłączony. Nigdy nie robiłem dokładnych testów. Pozdrowienia

[@mariuszjaskul271]

Padły mi 3 baterie.... Mam nadzieję że to pomoże.

[@nickedmonton8223]

So, if both lights are blinking, the battery is NOT charging?

[@makeandfixathome]

No, that is a fault

[@nickedmonton8223]

@@makeandfixathome OK, I guess you mean, "No, the battery is not charging due to a battery fault." I guess I need a new battery. It worked great when I bought it, but I let it sit for three years, so the battery is probably just dead. Thanks.

[@makeandfixathome]

@@nickedmonton8223 try this start watch from 2:30 kzbin.info/www/bejne/anqYp6KOnMiMbsU

[@delilablacklist]

I just bought mine and it's already not working. I shouldn't have to do all this. Maybe it's just a shoddy product. I've seen a few posts about them not working.

[@makeandfixathome]

I have 6 of that batteries and only one was faulty, bring it back to Lidl they will replace it.

[@delilablacklist]

@@makeandfixathome Thank you. I'll do that tomorrow.

[@makeandfixathome]

@@delilablacklist You're welcome :)

[@philgallier2690]

merci bcp

[@makeandfixathome]

You're welcome :)

[@suzanevieira4810]

thanks

[@makeandfixathome]

Anytime :)

[@JNikonT]

zyliss 👍👍👍

[@makeandfixathome]

thx my Friend!!

[@JNikonT]

@@makeandfixathome Vor 40 Jahren in Hamburg auf einer Messe gekauft mit reichlich Zubehör. Original Zyliss.

[@makeandfixathome]

​@@JNikonTthis is a perfect vice a swiss precision :) I still have the original box and accessories!! as You can see mine is a perfect condition, years in the box :) Purchased October 83' price £55 Regards from UK

[@JNikonT]

@@makeandfixathome 👍👍👍

[@ErCanEverything]

👍👍👍🙂🙂🙂🤝

[@XyberZyen]

Wrll i have no problems

[@fabientuizat1129]

thank you !! what is the ref for the IC please

[@makeandfixathome]

LGT8P22A

[@fabientuizat1129]

@@makeandfixathome merci !! data is very no easy to find

[@makeandfixathome]

@@fabientuizat1129 no problem, anytime! this is very true!