Nice sharing on how to open the TB. Already cleaned the IAC, now its working just fine.
@PotiaGraphy2 жыл бұрын
Sometime idling problem not coming from idling sensor... Its come from vacuum 16mm (13mm maybe forgot) hose (cracked and buy new one at spare part shop about rm3 per meter) but when u clean the throttle body it good time to clean that idling sensor... Good job and very details video... Actually I have subscribed your channel long time ago.... I also alza user...
@ctchan62103 жыл бұрын
thank you very much, the 12mm nut is very hard to open, suggest to use a 1/2" socket, also to open the sensor screw, use a hammer to tap on the screwdriver before opening ( to loosen it up), however i also broke the plastic socket clip just like you
@qarmax33 жыл бұрын
thank you
@metzmatu84093 жыл бұрын
The one you referring as idling sensor is IACV or IAC Valve. An idle air control actuator or idle air control valve (IAC actuator/valve) is a device commonly used in fuel-injected vehicles to control the engine's idling rotational speed (RPM).
@jh-ow2zd3 жыл бұрын
Tq. Good info. Many spare part shops still call it idling sensor! 😁
@cvsempoi3 жыл бұрын
If it has 6 wire, then it's a stepper motor controlling the valve. If it less than six wire prolly an actuator(never seen one attached to a throttlebody before). Calling it a sensor is way off...
@fauzeeismailismail77283 жыл бұрын
Nice ☺️☺️ bro
@fr3ak844 жыл бұрын
Thank for informative video! Do I need to reset the learning afterwards or it will auto fix by itself.
@jh-ow2zd4 жыл бұрын
You can reset if u want immediate re-learning
@mohammadfadilbinabdulwahab57063 жыл бұрын
Good video.
@jh-ow2zd3 жыл бұрын
Hi yes actually my k&n filter looks upside down compared to the normal filter but thats the only way it fits.
@agsham2993 жыл бұрын
just done mine...thank you bos for your info and instruction...really nice info...please make more video for our alza car...hehehhe
@firdauspiat95064 жыл бұрын
nice
@somestranger19973 жыл бұрын
I thought the bolts need to be tightened with 22Nm of torque? Or just hand torque is ok already? Ive seen other videos use torque wrench for tightening the bolts
@jh-ow2zd3 жыл бұрын
Its great if you have the torque specs. Pls follow it. Over tightening or under tightening can cause an air leak and rough idling. Fortunately the Alza has a big rubber gasket which seals the throttle body and allows quite a big margin of error that you can use hand tightening!
@vinric8848 Жыл бұрын
Apa punca kalau engine gegar kalau idle,,,blh jadi ini kotor kh
@saifuddinbahari66844 жыл бұрын
hai bos, after doing this service..when to make next service? tq bos..
@jh-ow2zd4 жыл бұрын
Trottle body recommended cleaning every 2 years
@edwinedwin6453 жыл бұрын
By cleaning the throttle body and sensor does this helps to relieve the low idling speed as my motor tends to have low idling speed when in gear, standstill and gear shifted to drive. Does this also helps with the fuel efficiency and responsiveness too ? I have already cleaned up the ignition coils but unfortunately I haven't noticed much improvement though. Thanks in advance !
@jh-ow2zd3 жыл бұрын
Low idling is good unless its too low and your car starts to vibrate then yes, cleaning the throttle body will help. Doesnt really do much for fuel efficiency
@edwinedwin6453 жыл бұрын
@@jh-ow2zd yes it does vibrates and when placed back in neutral it's better . Besides it getting more and more sluggish
@edwinedwin6453 жыл бұрын
You mentioned that after putting in the back 10mm screw then you can put back the wiring harness for the idling sensor but I see you have put back the wiring harness already at 12 minutes and 10 secs. So may I ask when should I put back the wiring harness ? Thank you in advance
@jh-ow2zd3 жыл бұрын
Yeah sorry you can put it back anytime. If you put it back at the 12.10 mark it would be easier
@edwinedwin6453 жыл бұрын
@@jh-ow2zd Great videos buddy I really enjoy watching them !
@markmark22223 жыл бұрын
good work brother but I like your watch
@jh-ow2zd3 жыл бұрын
Oh cheap watch only ☺️
@markmark22223 жыл бұрын
@@jh-ow2zd but still look good
@jh-ow2zd3 жыл бұрын
@@markmark2222 😁
@VivoY-nu5nx3 жыл бұрын
Kalau timing kacau..kene cabut wayer negetif ke dua2 skali..negtif positif
@jh-ow2zd3 жыл бұрын
Cabut negatif cukup
@edwinedwin6453 жыл бұрын
thanks for your video I was able to remove the throttle body for a clean up. Just a query, the canister vacuum hose contained a lot of water as I removed it. I was unable to search much info online. Would you kindly know what the issue is ? thanks again
@jh-ow2zd3 жыл бұрын
Are you sure its water? There shouldnt be any water there. You should check your purge solenoid (FICD) is working and charcoal cannister is not clogged
@edwinedwin6453 жыл бұрын
@@jh-ow2zd wasn't able to open as I need to get a torx screw driver. Besides there was for 4 Philips screw head that I could of opened but due to insufficient tools I wasn't able to open up just yet. Throttle body I managed to clean out. For your info mine is a daihatsu sirion 1.3 kv-3e 2006
@edwinedwin6453 жыл бұрын
Hi Jh just wondering if you might know. I have a steering issue Each time I turn left and right I always hear a clunking noise coming from the steering column. Would you have any ideas what this problem could be ? Thanks in advance..
@jh-ow2zd3 жыл бұрын
Depends on what sound could be steering rack or could be drive shaft or bearings. Hard to tell without listening. Do u notice power steering fluid level dropping?
@jhp88163 жыл бұрын
Hi does 1.3 myvi lagi best have the same throttle body so that i can cleanse my 1.3 myvi's in the same way?
@jh-ow2zd3 жыл бұрын
Yes i think so!
@mohdmohdnaim52714 жыл бұрын
Just sprey2 cm tu ja ka..lap2.tk payah sembur angin.
@jh-ow2zd4 жыл бұрын
Tak payah sembur angin. Itu trottle body cleaner cepat hilang
@mohdazhar67493 жыл бұрын
Boss....kalau buka sensor throttle body tu, lepas pasang balik, kena cucuk komputer atau tidak. Sebab ada kawan yg kata kena pergi kedai setting balik. Tq boss
@jh-ow2zd3 жыл бұрын
Tak payah cucuk computer. Boleh biarkan ambil masa belajar balik. Kalau nak reset pun boleh. Buka wayar negatif bateri tunggu 5 minit. Lepas tu pasang balik. Tapi radio kena setting balik.
@joannewong68993 жыл бұрын
Why u didn't cut the broken hose(the broken part only) and fix back. The broken socket clip can put epoxy gum to tighten it.
@jh-ow2zd3 жыл бұрын
Oh i just replaced the hose as it was getting old and brittle anyway. Good tip on the epoxy gum!👍
@metzmatu84093 жыл бұрын
Not recommended to use expoxy gum on those hose.
@ronymooney61752 жыл бұрын
did someone know what is called for that broken hose? so I can find it in a shop, mine hose are broken too
@akmalsyabil72324 жыл бұрын
Do cleaning vvt solenoid video please
@jh-ow2zd4 жыл бұрын
Oh why? You got a check engine light?
@jh-ow2zd3 жыл бұрын
kzbin.info/www/bejne/fam9e2pqeb-hp8k
@TheHeavensHell063 жыл бұрын
Bos...how u Clean the IAC? Using the carb cleaner or electrical contact cleaner? Tq in advance
@jh-ow2zd3 жыл бұрын
Carb cleaner
@metzmatu84093 жыл бұрын
Electric contact cleaner not strong enough to clean carbon deposit.
@RayoLisz89_SIT3 жыл бұрын
if engine on.. can service also?
@jh-ow2zd3 жыл бұрын
If engine bay on, mechanic usually service the lazy way. Just spray only. Never disassemble anything. But its not very clean. And any dirt will get pulled into the intake manifold
@strawhatbluenote97183 жыл бұрын
Idling sensor and throttle position sensor....is it the same thing? Tq
Hi, is that MAF sensor on the side of throttle body?
@jh-ow2zd Жыл бұрын
No. It is in the air filter box
@smartunnel Жыл бұрын
@@jh-ow2zd I found it. looks like a simple plastic thingy. Does it need to be cleaned?
@jh-ow2zd Жыл бұрын
@@smartunnel urm dont know
@yipee52473 жыл бұрын
bro, u clean the idle sensor with the cab cleaner u show in the video? will this cab cleaner affect the idle sensor after cleaning?
@jh-ow2zd3 жыл бұрын
Nope no adverse effects.
@azizanm23 жыл бұрын
You should change that broken vacuum hose. It will effect engine performance.
@jh-ow2zd3 жыл бұрын
Tq for your concern. Yes i have changed it
@ronymooney61752 жыл бұрын
@@jh-ow2zd hello, how much is that vacuum hose cost? you only replace the shorter hose or the long one? mine is broken too, for now I use cable tie only 😅
@jh-ow2zd2 жыл бұрын
@@ronymooney6175 i don't remember the exact amount but it was cheap. Less than 10 bucks i think. Can't even remember which one i changed
@ronymooney61752 жыл бұрын
@@jh-ow2zd i see. Can you share the link shopee? I can't find it, so many hose, i scare i buy the wrong one
@felbiangoh4 жыл бұрын
Bro I accidentally stripped my idle sensor screw. Any idea to unlock it.?
@jh-ow2zd4 жыл бұрын
Oh no! Is it possible to use needle nose pliers to turn the screw?
@felbiangoh4 жыл бұрын
@@jh-ow2zd I will give it a try. Thanks bro
@MrAcc453 жыл бұрын
@@felbiangoh Get an impact driver ard rm30. got cheap one also rm15
@mohdmohdnaim52714 жыл бұрын
Sensor batang dalam tu yang berkerak tu lh kena bersikan ye
@jh-ow2zd3 жыл бұрын
Ya
@metzmatu84093 жыл бұрын
Ada satu lubang di dinding tempat IACV tu masuk, spray utk cuci juga ya. That is the passage way where the air enter the intake manifold when idling to keep the engine running, the butterfly is close when idling.
@abgrudy39333 жыл бұрын
Idle sensor kalau pasang yg bawah ke atas ada effect ke?
@jh-ow2zd3 жыл бұрын
Tak pasti la 🤭
@metzmatu84093 жыл бұрын
I believe they call that idle air control valve (IACV). (not sensor, MAF is the sensor) Notice its rounded... it doesn't matter which way is up it still work. It work as a plunger moving in & out to control amount of air bypassing the butterfly valve for idling. (During idling the butterfly valve fully close)
@arifaipai11684 жыл бұрын
Awk tk tunjuk cara cuci dgn lebih teliti n mendalam. Awk just tunjuk cara buka n pasang je.
@jh-ow2zd4 жыл бұрын
Guna spray tu spray je
@Soul-gk5dn3 жыл бұрын
Sy sudah bg bersih throttle body tu,tp kereta masih hidup dan mati.kena restart baru boleh jalan.kenapa mcm tu ya.kena ganti baru dah ke..umur kereta 8 tahun
@jh-ow2zd3 жыл бұрын
Kalau cuci tak bantu kena tukar idle sensor itu.
@Soul-gk5dn3 жыл бұрын
Ooo...ok.sy cuba esok..thanks bos
@jh-ow2zd3 жыл бұрын
@@Soul-gk5dn invol.co/cl3gptq
@jh-ow2zd3 жыл бұрын
@@Soul-gk5dn RM50 lebih je kalau diy
@FaizalMustari4 жыл бұрын
Hi boss,bole u bg size tools yg diguna?btw done subs bos.
j h terima kasih atas info ni boss...maju terus boss👍🏻
@Farid-ns1dx4 жыл бұрын
Masalah Lampu meter menyala dan tak bole hidup knp ye bole bantu tak boss?
@jh-ow2zd4 жыл бұрын
Bateri kot. Tanya dalam facebook ALZA CLUB MALAYSIA ramai akan bantu
@mobiletube-gaming223 жыл бұрын
Throttle can clean and use back? Car workshop say must change new one 🤑🤑
@jh-ow2zd3 жыл бұрын
Depends on the condition. Sometimes clean the sensor oredi timing stable. Sometimes clean also no difference. Sometimes the butterfly also got problem got to change the whole trottle body not only sensor
@jekazevin60154 жыл бұрын
kalau terus pam tdk perlu buka, itu boleh kah?
@jh-ow2zd4 жыл бұрын
Tak bersih klu buat macam tu
@naznazrin85883 жыл бұрын
Good video especially for those who doesn't know, but sir i think your position of air filter is wrong. The bulge put should be the other way up
@jh-ow2zd3 жыл бұрын
Tq for saying! Yeah i know normal filter should be the other way up but this filter only fits in this way unfortunately.
@naznazrin85883 жыл бұрын
@@jh-ow2zd anyways do you notice any difference in performance after doing this cleaning? Ive noticed none
@jh-ow2zd3 жыл бұрын
@@naznazrin8588 haha this is not really for performance. This actually helps for idling. If your car stops at the traffic lights your RPM meter is more stable. For performance you should see my other video on cleaning the DVVT
@aquarian3114 ай бұрын
Tak payah pakai jam tangan lah nanti scratch..aiyoooo