Phreakmods Link: Introduction and Install onto Sanwa JLF

[@rocknmetalultima]

Hey big thanks for this vid. I bought the link and just installed it today with help of this video.

[@sambody5007]

I use the Sanwa extended jlf aluminum shaft in my case because my joystick is lower in my case. PhreakMods should make a variation of the link with an extended shaft for those that have their joystick lever lower in the case, but still want the quick disconnect function.

[@Nyasiu]

Couldn't you just buy a rising mounting plate...?

[@RickRothstein843]

Is this compatible with the sanjuks v3?

[@Loque69]

0:27 is it only me or the link is bit shorter than normal JLF shaft?

[@Xx_CourtPig_xX]

Same directions for a hori? Right

[@markmononoke7672]

Only issues that I really have is that sometimes it’s so so so hard to unscrew the ball top from the link. It’s just stuck on there.

[@DaneMurdock]

Does that added thickness along the stick ever bug you? part of me feels like the latch would be annoying compared to a thin, regular stick. Otherwise this seems like such a great solution to an annoying problem of transporting arcade sticks.

[@GrayscaleofS1]

I have an extra plastic collar on my dust washer and the thickness never bothered me, i don't have the phreakmod link, but i assume itd be like having the plastic collar on your stick

[@TheWillysardus]

Is there a "The Link" lever for the crown CWL 309?

[@focusattackcom]

focusattack.com/detachable-shaft-for-crown-cwl-30x-series-levers/ Not developed by Phreakmods, but does offer similar capability.

[@kyo9111]

Is this fit in victrix arcade

[@focusattackcom]

More than likely so long as Victrix uses a Sanwa JLF-TP-8YT lever. It always has used this model before.

[@kyo9111]

@@focusattackcom good thanks

[@HX2-MSH]

Hi, this shaft is compatible whith matcatz alpha stick?

[@jaleelbeck2413]

At the moment I cannot say. The Alpha uses a Sanwa clone stick, rather than a Sanwa JLF. It may work, but the models of Sanwa clone sticks can vary a bit. Therefore I can say it will not work with the existing lever; your best bet is to get an authentic Sanwa JLF, to which you can install into the Alpha.

[@animefrasier]

The link is awesome my only complaint is it keeps boping up and down

[@gtrboy77]

Who gets the credit for design and/or inventing this?

[@NettoZero]

Just purchased one during the sale, I did have a quick question. When I installed it, the e-clip i removed from my TE fits loose around the link shaft and slides off resulting in a loose stick (it does not snap onto the Link shaft like it does the stock shaft). When I reapply the clip to my old TE shaft, it works fine and holds it steady. Do I need to purchase a new clip or a new shaft for the link? Thanks

[@focusattackcom]

Can you post a photo to [e-mail]? Spoke to Phreakmods and he said: "Hmm, it's possible the e clip is worn, but it's also possible it was a defect in that machined spot on the base of the link, can he send a picture of the e-clip slot from the Link's base?"

[@vinnysob6380]

@@focusattackcom i recently purchased two of these from you and I am having the same issue. Yesterday, I was in the middle of a DOA6 match and the whole shaft pulled out because the clip popped off. The clip was loose on both of the phreakmod shafts and I can slide them off by hand, but I need a flat screwdriver to get them off of the stock JLF shaft. I just ordered a third one from another vendor for my current build. I hope it works better because I really like this product.

[@focusattackcom]

@@vinnysob6380 Can you please reach out to [e-mail]? I will also speak with Clayton of Phreamods about this.

[@vinnysob6380]

@@focusattackcom will do. Thanks. It's an awesome product. Update: Thank you for reaching out. Focus Attack and Phreak Mods took great care of me. I was sent several replacement lower shafts, even though I only needed two. The replacement shafts work as intended. Both of these companies really go the extra mile to make sure their customers are taken care of. I will be installing the Phreakmod EX Grooves on all my builds.

[@geofflao5321]

what buttons are those

[@focusattackcom]

GamerFinger HBFS focusattack.com/gamerfinger/

[@healtc5069]

Doesn’t look like this would work for a bat top....

[@focusattackcom]

It does fit a battop.

[@martydom9820]

Yeah Im rocking a bat top on mine, love the thing