Pick up Roller Lexmark MS811 M5155 M5163 M5170 MS711 MS810 VIDEO TUTORIAL

[@mustaphaalhiane9598]

hi the expert. I have a problem with minolta c200. code p-5 and p- 20. I remove the image unit and clean the corrona. after 20 copies I find again the waste o level of the corrona with lines on the copy.

[@MrRicoh]

IDC sensor/Fr failure, IDC sensor/Rr failure. • During IDC sensor light intensity correction, output voltage detected for all eight sample patterns are 3.35 V or more. • During IDC sensor light intensity correction, sensor output voltage for light intensity selected after the correction is under 0.7 V. • During IDC base surface detective control, sensor output voltage detected is under 0.7 V or over 3.35V. • During image stabilization (gamma correction control), detected output value for IDC sensor did not go below threshold (half the value of what is detected by IDC sensor on the belt surface) for three consecutive times (position of the pattern end is not detected). • During image stabilization (gamma correction control), sensor’s output value of each color for hyper 0 gradation after the primary approximation is half the detection level on the belt surface or under. Causes • IDC sensor/Fr (IDCS/Fr) • IDC sensor/Rr (IDCS/Rr) • IDC sensor shutter solenoid (SD2) • High voltage unit (HV) • Image Transfer Belt Unit Remedy 1. Wipe clean the surface of the transfer belt with a soft cloth, if it is dirty. 2. Replace the transfer belt unit if the transfer belt is damaged. 3. Reinstall or reconnect IDCS/Fr assy or IDCS/Rr assy, sensor shutter or connector, if it is installed or connected improperly. 4. Clean IDCS/Fr or IDCS/Rr if it is dirty. 5. Check the HV connector for proper connection and correct as necessary. 6. SD2 operation check. 7. Open/close the front door, run an image stabilization sequence, and select [State Confirmation] -> [Level History 1] to check the IDC value. If the value is 1.0 V or less, replace IDCS/Fr or IDCS/Rr. 8. Replace MFPB.

[@greatnew_products7436]

Did he clean it? Replace it? What happened?

[@MrRicoh]

The printer does not pick up paper and has frequent paper jams. Replacing the rollers with new ones helped. 🔥🔥 KZbin SUPPORT: kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin

[@necrocritter]

i've got a constant paper jam display, cannot print anymore.

[@MrRicoh]

In this case, I replace the paper pick rollers and the printer prints again. Search numbers: 1. Pickup Roller Assembly 40X7593 2. Separation Roller Assembly 40X7713 If you can, please become my subscriber. It's free, and that's very important to me.

[@mirsaddelicmirso]

MS510de?

[@MrRicoh]

Hi. You are actually right. Every real movie I did with the Lexmark MS610 printer, but they are almost identical devices. In any case, the paper pick-up roller is exactly the same. Lexmark MS510dn Pick Roller Assembly 40X8443. Also fits these models: Lexmark M1145 Lexmark M3150 Lexmark MS312dn Lexmark MS315dn Lexmark MS410d Lexmark MS410dn Lexmark MS415dn Lexmark MS610de Lexmark MS610dn Lexmark MS610dte Lexmark MS610dtn Lexmark MX310dn Lexmark MX410de Lexmark MX510de Lexmark MX511de Lexmark MX511dhe Lexmark MX511dte Lexmark MX610de Lexmark MX611de Lexmark MX611dhe Lexmark MX611dte Lexmark XM1145 Lexmark XM3150

[@mirsaddelicmirso]

@@MrRicoh Thanks

[@dauglasbugingo7331]

Halo engineer, I want to be your student

[@MrRicoh]

@dauglasbugingo7331 What printers or copiers do you deal with? Provide the make and model.

[@pradeeponline5768]

Print beech m chhod rahi h

[@pradeeponline5768]

Plz contact number

[@MrRicoh]

Check your fuser unit, check drum unit, where you need to find the cause

[@MrRicoh]

you can only write here.