hi, I tried everything to reproduce Dolby 5.1 on my Onkyo TXSR494, nothing to do, I can reproduce DTS and DTS-HDMA perfectly but I can't hear anything in Dolby 5.1 or Dolby Atmos. Could it be this chip's fault or should both formats have problems? thanks good work
@wooody1012 ай бұрын
Hey I have a Pioneer VSX-1131 receiver, and the LED display doesn't work. I have checked that it isn't just dimmed and it's not that. How would you go about troubleshooting that? Any help would be much appreciated!
@technoboy-allinOneАй бұрын
check the flex cable first
@papuprathip883 жыл бұрын
Great Video ❤️! Pls advise this. I use Pioneer VSX 523. The centre Speaker suddenly gives very less sound though it is set to +15db. All other channels are working fine in all the sound modes. Kindly help.
@technoboy-allinOne2 жыл бұрын
Reset the receiver & setup again
@43Serbia Жыл бұрын
@@technoboy-allinOne i have the same issue with front left channel. Pioneer vsx-921k. When i use analog input in pure direct, it works fine. But when i use hdmi or any digital option etc pro logic II, front left chanel is bad. Any solution? Is hdmi board bad, or any of its component, or should i look for something else, since all other chanels works well with digital input? Thanks!
@RavikumarRelangi7 ай бұрын
Hi any idea about wifi Bluetooth and net not available on vsx 1131
@technoboy-allinOne7 ай бұрын
Try reseting it
@febinjohny65574 жыл бұрын
I am using Sanyo XT-49S7200F49 inch (123.2cm) Full HD IPS LED TV, it has 3 HDMI connections(2 HDMI on the side and 1 HDMI at the bottom). In HDMI 2 it's showing "Audio Out"(Not labelled ACC), whether the port has the feature of ARC (Audio Return Channel). Is this model ARC connection feature to connect my home theatre ??? Based on your valuable videos I purchased a pioneer HTP-076 (Main unit (VSX-326) ). How do I connect to my Sanyo nxt 49-inch tv? Please make a video.
@kunalraut95093 жыл бұрын
Good video.... In case dts decoder chip needs to be replaced then do we need to install firmware again.... because there is still no sound issue with some receiver even after replacing faulty dts chip...thanks
@technoboy-allinOne3 жыл бұрын
Yes. Firmware is mendatory to install after replace the chip.
@domenicoorefice72692 жыл бұрын
hello, I am writing to you from Italy, I am a Pioneer lx90 owner, my beloved amplifier has a problem, the lcd display fizzes continuously, how can I solve the problem? thanks Domenico
@technoboy-allinOne2 жыл бұрын
Try resetting the receiver. If the fault doesnt go then it might be lcd connection problem or the lcd itself. Though its not clear to me that except display everything else is working as ususal.
@domenicoorefice72692 жыл бұрын
@@technoboy-allinOne however when I continue to select example phono, cd etc for a long time it does not sparkle the display, when then I select what I need after 30 seconds it sparkles again
@harryk.35953 жыл бұрын
hi, great video! i have this pioneer and its working well BUT no sound from AM/FM section. it receives and stores the stations but no audio at all not even the static noise. kindly help. thank you
@technoboy-allinOne3 жыл бұрын
I use the receiver for home cinema. Never used the fm till now.. but i think there wouldnt be any noise untill it catch a stations. Connect the am loop antena properly. And place the fm antena wire properly. Then try again
@harryk.35953 жыл бұрын
@@technoboy-allinOne thank you for your response. i think my machine has a problem coz the aerial is ok, its receiving all the stations well but no sound at all.
@RickyBailey-n7q11 ай бұрын
Yes , I have a pioneer vsx-521 my friend took the fm am box and took it out can you show me how to hook it back up inside , please
@technoboy-allinOne10 ай бұрын
Sorry bro. Mine is long gone
@vukvukovic70642 жыл бұрын
I have sound only in pure direct mode, checked voltages they are all fine... but no sound in other mods... only pure direct on fronts... do you know what is the problem??
@technoboy-allinOne2 жыл бұрын
Most probably its the faulty decoder chip. Replace it. But before that reset the receiver & see if the problem is gone
@vukvukovic70642 жыл бұрын
@@technoboy-allinOne The problem is still present, headphones not working also, no digital inputs only analog and in pure direct mode... thank you, it si dsp chip 100%... I will try to reflow, and maybe buy it form ali expres xDD
@amjadali-tv3si9 ай бұрын
Heat skins were by default provide by manufacturer?
@technoboy-allinOne9 ай бұрын
No. Not in this model
@eugenenephtalimagsalin72982 жыл бұрын
I have vsx 522 K and my tech told me to replace the digital main board. I manage turning on the power by pressing power & advance surround button at the same time. sometimes it turns on & goes off. Im able to connect my amazon firestick on HDMI and it works but theres no audio on every thing,...on tuner, dvd, cd?...do I really need to replace the HDMI BOARD? do you where can I buy a replacement board?
@technoboy-allinOne2 жыл бұрын
Hard To Find, Only Authorised Service Center Can get you that I guess. But You can try on bangood & aliexpress
@nespecificiran Жыл бұрын
Hi, i need some advice if you can help me? I have phenomenal av Pioneer vsx 2021, and one day problem with sound starts. I opened amplifier and found that smd chip "Bridge co dm860" when is heated, amplifier starts to lose sound. I mounted aluminium block with cooler direct on the chip, but after i using amplifier all day then same problem occurs. What do you think, can resoldering fix the problem, or i need to replace the chip? Thanks in advance😊
@technoboy-allinOne Жыл бұрын
Replace is the last option. First you gotta check the other parts around it. Maybe its supplied over voltage or current to that chip, thats why its heating up.
@andrewmccain66073 жыл бұрын
Tenement...............
@pacohernandez89242 жыл бұрын
Hello, I have a question, I have a pioneer elite vsx-53 manufactured in April 2012, the code UE22 appeared, it presents an audio fault, it takes 10 minutes for the sound to come out, then there is no fault, I turn it off and on and the code goes away, but the next day it is Even if I restarted it, it doesn't fix itself. If I change the new dts chip, then do I have to update it or just change it and nothing has to be done for it to work??? I hope you can help me thanks greetings from Mexico 🇲🇽
@technoboy-allinOne2 жыл бұрын
Ue22 is firmware update error. Try resetting the receiver.
@farmerbob3392 жыл бұрын
I get either Working Perfectly or FULL VOLUME SCREECHING/BUZZING/OSCILLATING Sounds out of the speakers then the HDMI blinks. Glad it hasn't blown any of 8 JBL 4312s. Pressing the Power Button to turn it off gets you "POWER ON" on the display and the unit fires up. So I guess it turns itself off. This just started with one UE22 Error after, I want to say, 10 years (?). To tell the truth, this unit never sounded as good as my 3 previous AVRs. Onkyo/Pioneer, if I only had known. Should have stayed with Yamaha.
@martinkrejci1703 жыл бұрын
Hello, could you please advise me? I'm still an electronics student. I have a Pioneer VSX-921 receiver, but the sound stopped working. It does not go into headphones or an amplifier. I play the sound from the internet radio. Where could the problem be? The board voltage is OK, but the 7812 has 13.3V at the output and the 7912 has only 11V at the output. Can this be the cause of the problem?
@tonifatec3 жыл бұрын
Pre amp board needs matching +12v/-12v.
@grlin14543 жыл бұрын
Hi, I have the sc-lx90 but its front channel is damaged due to the extremely loud output during operation. I sent it for repair but one front channel keeps burned out after relacing chips. Can you orovide me some guidance?
@technoboy-allinOne3 жыл бұрын
Check for speaker impedance. If your speaker impedance is lower then the receiver recomend, then the transistors will keep blowing.
@damienjanecky60882 жыл бұрын
Hey, I have a pioneer AV receiver VSX-524 I got used from a coworker, about 2 days after setting it up and getting surround sound ARC working through my TV it started buzzing slowly getting loud out of all speakers. Shortly after, I lost sound in my front left channel then after swapping with the same model speaker (6ohms) still nothing and after switching back my center channel was dead too. I tried reseting it, reseting the error codes, unhooked from literally everything then hooked back up basic left right and the left channel was still dead and buzzing remained in both speakers even with no inputs and nothing else close to it or in the same outlet. The buzzing gets quieter when I dim my display brightness on the receiver (no clue why) Any and all advice is very much appreciated as I am new to receivers, although I have done some soldering and wiring before for high power nerf mods so not scared to attempt a fix.
@technoboy-allinOne2 жыл бұрын
First reset the receiver & see if the fault goes away
@damienjanecky60882 жыл бұрын
@@technoboy-allinOne I did a few times already, no changes
@abhinavpatil24163 жыл бұрын
Hi, I have the same reciver my hdmi bord is gone, but the optical works properly but it takes so long for the reciver to detect sound from tv, please give any solution to solve the optical problem
@technoboy-allinOne2 жыл бұрын
Hdmi or the logic board has the dolby decoder chip. All the audio input signals go through it. So you need to repair the kit
@Killer483-cat3 жыл бұрын
Hi my pioneer av receiver vsx 523 5.1 but only 3 out are have sounds other two has no sound front and rear wgat to do plz reply
@technoboy-allinOne3 жыл бұрын
Need some more details to clarifiy your problem. You can mail me too
@majkym53 жыл бұрын
Hi. I have same problem with my yamaha rxv773. The dsp chip was D80YK113CPTP4 and I replaced it with D80YK113DPTP4. That is updated version of cptp4. Now i have speaker icons right away after turning the power on but NO SOUND, NO TEST TONE no nothing. Did the complete diagnostic and no errors found. Maybe i got bad chip?
@technoboy-allinOne3 жыл бұрын
Maybe the chip is not bad but its not a complete match to the logic board. Try resetting the receiver & check if it works
@majkym53 жыл бұрын
@@technoboy-allinOne i did reset, nothing. I run self diagnostic and no foult was present. In texas instrument document says that this is newer version of the chip. Pin to pin same. New receivers have that chip instaled dptp4. I saw it in the store before i bought the chip. Tuner works in pure direct mode. Either chip is bad or the tech who replaced the chip screw something up. I found little balls os solder after replacement on some chips and capacitors. I removed that before instaling the board.
@shaikshavalishaik11923 жыл бұрын
I have pioneer vsx-329 amplifier it's producing unnecessary noise when it is turned on, what is the problem in it
@technoboy-allinOne3 жыл бұрын
What type of noise? Remove all the inputs & check again. If no more noise that means inputs problem. If still problem persists then try reseting the receiver. That should slove the problem. If still the problem is there then the receiver must have physical connection or faulty or loose parts problem.
@shaikshavalishaik11923 жыл бұрын
@@technoboy-allinOne Thanks for ur reply,I have removed all the inputs eventhough the noise is coming , if we connect input the audio will play for few secs and audio will stop and the noise comes again , is there any problem in mother board?
@technoboy-allinOne3 жыл бұрын
I think so. That board is called logic board. I think it has a input detection problem. Contact service center.
@DrAVRECEIVER2 жыл бұрын
Bro needed help.... My pioneer vsx 1131 it displays NG: LCRSLSRBLBR DET PROTECT i
@technoboy-allinOne2 жыл бұрын
try reseting it
@prabhushankar47023 жыл бұрын
My Denon 4311CI shows DSP 01 error, only audio out not working rest of the things working fine. How to fix this..
@technoboy-allinOne2 жыл бұрын
Need to replace the chip
@baneesh292 жыл бұрын
Halo sir Usb reading issue and no sound You have dsp flash file ?
@technoboy-allinOne2 жыл бұрын
Sorry bro,dont have that
@vuhoangthuan3263 жыл бұрын
The D-Dac Bridge Assy AWX9570 of my Pioneer SC 37 Receiver was broken. I am looking for the replace one but cannot find. I would like to thank to everyone who help me find it.
@technoboy-allinOne3 жыл бұрын
Search on aliexpress or contact pioneer customer service.
@muchomorelektron6599 Жыл бұрын
Only replaceng dsp is fixing, all other methods are shitting right on face of clients. Heatsink dont change anything because heating fixes this sometimes if software is not corupted and only works for random amout of time. Fault will return. Only good corrected dsp fixes this permanently.
@andrewmccain66073 жыл бұрын
Its boyman...bowling
@sujeshintime74573 жыл бұрын
Sir vsx324 avr not reading usb. But usb port&wire are good how can you help me
@technoboy-allinOne3 жыл бұрын
If the port & the wires are fine then maybe the chip is bad. Or better try resetting the receiver. That may work if its the firmwere prob.
@spgizzi13 жыл бұрын
I have a pioneer vsx-324, i can hear sound from the front speakers when its set to SP OFF, i can also hear sound leaking between left and right channels when testing the speakers, when its set to left i can hear some sound from the right speakers and vice versa....
@technoboy-allinOne2 жыл бұрын
Reset the receiver. If its still same then maybe the decoder chip is faulty
@parmardharmendra23874 жыл бұрын
Yamaha htr. 2067. Power. Problem. Dad supply
@MrRajesh14583 жыл бұрын
I wanted digital board. Any. Chance. Place help. Me
@technoboy-allinOne2 жыл бұрын
i didnt find it either
@ajayvr13804 жыл бұрын
Helo I have a pioneer vas’s 324 it’s not producing sound while I connect it with Ac cable please help me
@technoboy-allinOne4 жыл бұрын
Does it turn on?
@ajayvr13804 жыл бұрын
@@technoboy-allinOne yeah it's Turing on but no sound
@technoboy-allinOne4 жыл бұрын
@@ajayvr1380 do you see your dolby pl2 on display? After turning it on do you hear another tick sound after few secs?
@ajayvr13804 жыл бұрын
@@technoboy-allinOne yeah the whole display shows everything but just doesn't produce sound
@spgizzi13 жыл бұрын
@@ajayvr1380 check that the speakers are set to on. it should display SP>A ON THE RECEIVER
@lakshmirajmuthiah49474 жыл бұрын
Please help
@lakshmirajmuthiah49474 жыл бұрын
Hi...my Pioneer VSX 934 issue with Bluetooth.... audio shutters for 1 sec frequently
@technoboy-allinOne4 жыл бұрын
Reset the receiver & check
@malesnada3 жыл бұрын
Yo tengo el mismo reciever, se me quemó la tarjeta de hdmi, que puedo hacer?