Pipe Length calculation use Sine & Cosine

Рет қаралды 11,620

Piping Engineering

Күн бұрын

Пікірлер: 42

@vusalbabirov3851 9 ай бұрын

Good job for your new videos

@Piping-engineer 7 ай бұрын

Glad you like them!

@audiobook-s 9 ай бұрын

Good luck with your new videos

@umeshchauhan8286 9 ай бұрын

Nice job brother ❤❤❤

@Piping-engineer 9 ай бұрын

Many thanks brother.Please liked and share this video for support this channel.

@vivianmasnin3471 9 ай бұрын

Euh non c'est faux une baïonnette parallèle à toujours les mêmes angles, en conséquences la valeur de la tige de chaque côté sera de 48mm pour 35degré , donc hypothenuse -(48×2). Les 55degré représente l'angle extérieur

@victordelfin1003 3 ай бұрын

Nice ❤

@mdirtaza368 9 ай бұрын

Great knowledgeable video

@Piping-engineer 9 ай бұрын

Many thanks for watching and comments

@45003500i 9 ай бұрын

Very nice explained

@Piping-engineer 9 ай бұрын

Many thanks for watching and comment,my friend

@tahraouiabderrezak7170 7 ай бұрын

Awesome

@paposanggo 9 ай бұрын

Thanks for sharing

@Piping-engineer 9 ай бұрын

Many thanks for watching and comments

@IfeanyiMicheal-z8m Ай бұрын

How many types of valve do we have??

@Piping-engineer 28 күн бұрын

Common used valves: Ball Valve Butterfly Valve Globe Valve Gate Valve Check Valve Pressure Reducing Valve Pressure Relief Valve Plug Valve Needle Valve Pinch Valve Diaphragm Valve Solenoid Valve Coaxial Valve Angle Seat Valve

@MafySetnaled-ki6vg 14 күн бұрын

Sir i have a question for you hoping to your reply.this is my question.calculating of pipe and true length are the same I'm correct sir?.HOW ABOUT DIMENSION OF ELBOW AND PIPE LENGHT SIR? Are also thesame?

@FilsmapuyaFils 2 ай бұрын

Comment vous aviez trouvé coude de 55 et 35

@arnelarriesgado8257 5 ай бұрын

Where did you get 55 deg

@Piping-engineer 5 ай бұрын

The sum of two internal angles of a right triangle must be 90 degrees, if one angle is 35 degrees, the other angle must be 90-35=55 degrees

@gue1675 23 күн бұрын

The elbow above is incorrectly calculated, it is not 35 degrees. 55

@stephenevans3824 4 ай бұрын

Hi please could you explain where you got 38.1 from in this formula ELlength-tan (elangle/2)x38.1x nps 4 thanks

@Piping-engineer 4 ай бұрын

It is standard. 1-inch 90-degree elbow length is 38.1 mm. 1-inch eLbow length = tan (90/2)x1.5x24.5=38.1 mm 4-inch 90-degree elbow length will be 4x38.1

@turalramazanov3881 3 ай бұрын

Hi.vhere from you found 300 ?

@farhanakhtar4530 9 ай бұрын

Sir could you upload a video on how to calculate rolling Angle and pipe angle, I'll be grateful to you for your help ❤

@Piping-engineer 9 ай бұрын

Thanks, ok will be done Please watch our new videos and write your comments. Your ideas are very valuable to us.

@mehemedesgerov4463 8 ай бұрын

Əla uğurlar

@Piping-engineer 8 ай бұрын

Avropaya salamlar

@lifetrace9687 9 ай бұрын

İlk once salam qardas , videolara gore tesekkur , amma fikir verirem ancag eyni videolar cekirsiniz , borunun hesablanmasina aid ne qeder eyni vide cekerler qardas ? Belke basqa basqa videolar cekesiniz ..Boruya aid milyon dene video cekmek olar ..meselen certyoj uzerinde Nort , West , El hesablanmasi qaydasi ..Certyoj uzerinde olan yazilarin menasi aciqlamalari , say say bitmez ..niye gore ancag eyni videolar cekirsiniz ? Katet hesablanmasi , boru hesablanmasi basa dusdukde qardas , kanalinda buna aid ne qeder videolar var..mumkunse dediklerimi nezerden keciresiniz , tesekkurler

@rajeshprasanna2606 9 ай бұрын

Names only can see .messure ments cants see What a channel

@brandolomabas6861 9 ай бұрын

IdonT understand that 300/0.4226=709.89 but base on your answer it is 828 mm how come?

@Piping-engineer 9 ай бұрын

Many thanks for watching and comments. 828 is correct. but I made mistake during writing calculation.I wrote 300, instead of 350. The drawing showing 350. Sorry

@tipkoala6171 4 ай бұрын

@@Piping-engineer I was getting crazy

@omersaglam9391 9 ай бұрын

90 derece ve 45 derece olan boru boyu hesaplamasını göster

@Piping-engineer 9 ай бұрын

Videolarımızı izleyib yorum yazdığınız için teşekkür ederim.Tamam en kisa zamanda yayınlarız

@tejeswarreddy4808 6 ай бұрын

drawings file secured bro please make it public

@Piping-engineer 6 ай бұрын

heyzine.com/files/uploaded/v2/f238fc514f8c6902c5b887f5319c6fab10430904.pdf-thumb.jpg

@Piping-engineer 6 ай бұрын

Thank you very much for your comment on my video! I appreciate you sharing your views and thoughts. Your support and feedback inspire me to produce better content.