Piping Engineering : type of gaskets used for flanged joints

G. S. Samanta : Engineering & Educational

[@Borntobeviral]

3 types of gasket mainly used 1. SS graphite spiral wound mentality gasket for raiaed face 2.Non metallic type ring gasket for raised face 3.Full face gasket for full face

[@sen-ow7ub]

It's amazing. how many times I watch this video over and over again, there's so much things embedded into this video

[@heshammatoug4860]

thanks for this clear explanation. one question, please. can we use ibc gasket instead of spiral wound gasket ?

[@29csamiran]

Can you please explain about the ring joint flange...like WNRJ...any video please

[@gourisankarsamanta7670]

@@29csamiran please watch my below video : kzbin.info/www/bejne/baO9YYBupNakodU

[@sen-ow7ub]

Really well explained. And we are understood very clear. Please make another part video about this topic. Please make minimum one video everyday related piping design, detailing, fabrication, piping welding and NDT requirements, construction Method and pre commissioning. . Thanks. Why there is no frequent videos now. When you going to post your next video.

[@daurentokkuzhuyev4791]

Very good, always seaching your New videos in your channel. I have got a lot knowledge. Want to tell many thanks. Dont stop and keep going Mr

[@looktv9080]

Good

[@sarankathir4857]

Very useful

[@positivevibes7713]

Can u make video on how read ga and fabrication drawing for piping design.

[@himelmahamud304]

It's helpful video ❤

[@abdoadam7248]

Thanks for sharing knowledge

[@chandrajeetsharma1]

Gd eve.. sir Sir i am also an engineer Right now i am struggling in this feild Sir could u tell me different between ASME, ASTM, API, ANSI, and could u provide me a pdf of it . It my humble request to u sir please 🙏

[@gourisankarsamanta7670]

Please watch my various piping videos, particularly the following : kzbin.info/www/bejne/jYnRnZmXd62DmaM kzbin.info/www/bejne/qXbNmqeAn5ljjpY kzbin.info/www/bejne/aJzMnHqOqKuZqtE kzbin.info/www/bejne/iGrbk4ijpseooKs kzbin.info/www/bejne/a3Kch2iVYreti6M kzbin.info/www/bejne/e6PIZn2GhqeIq6s kzbin.info/www/bejne/jImccq1-hpqSfpo kzbin.info/www/bejne/anvOap2Lgs2gqM0 kzbin.info/www/bejne/Z6jHfousjd-insU kzbin.info/www/bejne/gYvRZ3ykfqaDhas kzbin.info/www/bejne/g5-mo3ptpM2AjqM kzbin.info/www/bejne/imLWm4KPjZWKm9U kzbin.info/www/bejne/jYmxn613dth3esU kzbin.info/www/bejne/gIa8n2uqn5mqsJo kzbin.info/www/bejne/hJm4dXiirtKNmMU

[@chandrajeetsharma1]

@@gourisankarsamanta7670 gd morning sir thank you sir If i have any doubt i will contact u through this way

[@fireballxl5328]

not a simple question. all these folks compete but are also in bed together. As time goes by all the U.S. recognized codes and std get closer Ill try to get back when I have a bit more time

[@Borntobeviral]

3 types of gasket mainly used 1.SS graphite spiral wound mentality gasket 2.Non metallic type ring gasket 3.Full face gasket

[@Sam-81_98]

Hello Sir. Great video. Is it possible for you to recommend a good vendor who supplies flanges of International quality for the overseas market?

[@fireballxl5328]

Texas Forge, or check with MRC co stay away from China, Korea, India

[@pratikdaundkar5613]

very informative

[@Mr-er3yo]

I'm a emerging piping engineer sir your way of teaching is excellence.i keep on watching your videos.great efforts continue

[@Shivam.366]

Thanks

[@GemmyHeart]

nice.

[@rohitnikam3647]

Hi sir Can we use full face gasket on rf flanges

[@gourisankarsamanta7670]

Yes we can use it.

[@khairulislampipefitter4771]

SS gasket how to know