Pneumatic Punch Press Feeder

Pneumatic Punch Press Feeders are relatively cheap devices, however they can reduce manufacturing cost substantially. Servo controlled feeders slowly replace this old, but reliable technology.

[@stephensarkany3577]

Finally one where the work isn't thrown in a heap on the floor after every step.

[@FAcostaMX]

there are some flaps that back the coil over decoiler, the position of those flaps changes anytime from 1 roll to other...then the alignment between coil & die changes often. another reason we have to keep it far is that it is hard to synchronize the speed of decoiler and the feed in press. longer distance makes a buffer for this. linear speed of unrolled material slows down as roll is spent but press keeps a constant rhythm.

[@digitalmagic6651]

Thank you for the vid I can watch it all day, in a strange way it is relaxing.

[@mekanizmalar]

Than you for your visit and your nice comment. Actually, when we Operate it, I stand there and watched it an hour. It was combination of, I wanted to make sure it did not malfunction and enjoyment.

[@mekanizmalar]

@pontian16 No it is 1mm thick Iron. There is no particular reason for setting it apart from punch machine. We could have kept it closer. Next time I will try it closer.

[@brunokerbaul3826]

Hy at the end of the video... You should roll the rest parts it can be useful for other applications, ventilation systems, on planes to solidify the separations between bigger parts

[@tshepobrian9369]

Hey awsome demonstration but how did you set the pitch

[@mekanizmalar]

Three years ago I purchased it from Ebay for $250. It was a rare opportunity. I did not see similar offer since then. However, you might build an Arduino controlled system yourself doing similar job.

[@ronaldospinelli2649]

A mecânica é muito bonita fui preparador de prensas muito tempo

[@sumandriasumandria2253]

What is the punch force tonnage?what maximun rhickness of steel plate can be punched?what size or type of compressor needed?thanks

[@seyhanersoy8989]

The tonnage of the press is 30, which is considered a small press; the maximum thickness to be punched hole would be dependent on panch circumference. The Air pressure used in this system was six-bar, and it was a very old compressor. The punched hole diameter seen in the video is 12 cm. The plate's thickness is 1 millimeter.

[@orlandodanielmartinezsanch2391]

como le hace para que las.piezas queden arriba y no caigan hacia abajo al momento de troquelar

[@mekanizmalar]

Thank you.

[@expandtrading1192]

I need your WhatsApp number

[@mekanizmalar]

This is very old machine and it was in working condition, I purchased it from eBay for $250 (USA). I paid extra $100 for a valve that is attached to the press. I was lucky to find one. If you look up to eBay for "pneumatic feeder" you may find something to buy in there. I do not now the cost of new ones, but I am seure that they are above $3000 or more. My friend still use the one you see in the video.

[@DiogoSilva-bc1rn]

Bonecos

[@kunalpatil4797]

Operation name

[@nenzianwari]

A re-coiler or even scrap cutter at the end would be useful. Wouldn't want to pick that scrap up off the floor. Also the clamps used to hold die-set down although working are not appropriate.

[@mekanizmalar]

Yes, scrap cutter would help a lot. Now they use servo driver which includes also scrap cutter.

[@mekanizmalar]

No, I meant metal sheet rolls.

[@pontian16]

ohh..i thought you want to cool it or something, but the rolls don't seem to have heaters though..btw, i like your videos, it kinda help me in my studies, hope you can post lot more vid in the future.

[@mekanizmalar]

Hi Niket, Go to Ebay and search for "Punch Press". You may find what you are looking for.

[@claudiogomes6466]

Onde compro estampa de pregos telheiros para prensa excentrica ?

[@kibaservices54]

This machine is available along with small die also

[@FAcostaMX]

We use in my factory different kinds of feeder but decoiler/straightener is kept far from press.I don't know the "science" behind that but: it is hard to align rolls with dies, then longer distance minimizes the potential angle between coil & die.We keep the guides in the die as tight as possible.If material comes with a deviation, it gets stuck.Our dies/coils are hard to align due to different dimensions/location over press & decoilers usually have a screw to fit inner diameter of rolls. TBCont

[@pontian16]

sorry, i view in mobile....is that aluminum?..why the distance so long from the rolls to the punch machine?

[@barunpramanik786]

Is it possible to make two pieces in one stroke by the help of die???

[@user-Ranjan509]

yes

[@Pramods0077]

Beautiful

[@seyhanersoy8989]

Thank you.

[@ferhat.karacuha]

Başarılı bir çalışma olmuş, tebrikler..

[@metalenclosuremachines]

Good feeder and press

[@antwniaxatzikonstantinou2968]

Τρόμος ξύλου

[@mohmedahmed-vw2us]

Schéma électrique d'une presse mecanique a commande pneumatiques

[@mithunkolay8055]

What's price many,

[@seyhanersoy8989]

10 years ago I paid $250, I am sure that it may be more expensive now.

[@praveenagarwal9790]

Please send me your zig zag servo feeder stainless steel coil circle cutting machine video and details

[@ChandraShaker-e5e]

Which please

[@likeit173314]

What is The Price Of Machine? N How Much Thick Metal We Can Cut in It !

[@mekanizmalar]

This is a pneumatic punch press feeder. 10 years ago, I paid $250 and purchased it from eBay as a gift for my friend. You can cut up to 1.5mm thick metal strips.

[@rishimissan2897]

hi may i know the cost of this machine

[@DastarDhariCrowdMusic]

Very nice👍🎤

[@seyhanersoy8989]

Thank you for the lovely comment.

[@ramappamuniyappa5250]

Hai I want this type of machine for belt conveyors, rollers bearing housings, what is the cost

[@globalnatureagro6844]

contact us no guru [e-mail] [phone]

[@subbiahannamalai589]

9597708197

[@بدون.عنوان-ض6ظ]

I want to contact you to order the product

[@theoremsnagesh]

did you use pneumatic cylinder for this? wats the bore and short size used?

[@mekanizmalar]

I purchased pneumatic feeder from eBay. I don't know exact bore size but I guess it is 50mm. Stroke goes up to 200mm adjustable with stoppers.

[@theoremsnagesh]

Thanks and how much capacity of air compressor used for this? 2 HP?

[@mekanizmalar]

That I don't know. My friend has big compressor in his factory and they use so many pneumatic equipment and pressurized air was coming from a central compressor which was very large.

[@mikimiki886]

Machine name?

[@timjones5708]

Has anyone previously or currently ran an ST 1225?

[@amitkashyapkashyap9136]

Cost kitni h feder ki

[@hoangvukhieu2484]

Máy này giá bằng nào tiền và mua ở đâu ai biết chỉ cho mình nhé

[@nguyenviethung8840]

0985790381

[@praveenagarwal9790]

Pneumatic punch video and details

[@hoanglonghua2073]

I can design better

[@موسىمحمدعبدالواحدالابي]

مرحبا كم سعر خاذي المكينه

[@3PROBOT]

잘보고 갑니다 ~ ^^

[@rizvisha2092]

I want this machine how do you got

[@mekanizmalar]

I purchased it from eBay a long time ago.

[@riyashah5854]

go for auto servo fidder

[@amitbisnoi9276]

Please tell me your location, i need such type machine

[@Niket1111]

Can you Suggest the company that can manufacturer this for just circle cutting

[@dheerajgautam4384]

yesss i can help you...

[@Troll_Singh]

lots of that can make high speed for your requirements

[@ajaydeswal4672]

Its bottle middle bottom

[@babarali4897]

KO I now dai dekhu

[@honeybeekorea1553]

프레스영상 잘보고 유튜브 친구맺고 갑니다 허니비코리아 놀러오세요

[@busyhd558]

Luar biasa

[@mekanizmalar]

Thank you.

[@nclove502]

poszukaj czegoś z podajnikiem na paski ;)

[@praveenagarwal9790]

Praveen Agarwal ambica matal works moradabad INDIA

[@drrocketman7794]

Rise of the Machines

[@imranengineeringworksimran345]

Yeh ban Kiya Raha hai

[@arunshaw7364]

sir i need this machine

[@globalnatureagro6844]

do u need feeder?, contact us no guru [e-mail] [phone]

[@vikasthakur9380]

Global Nature Agro hey where are you from. I need this machine

[@riyashah5854]

you can save your westage

[@rameshchandmeena2483]

Me Kam kar sakta hu

[@iraqresitance9663]

From iraq greeting

[@seyhanersoy8989]

Greetings from USA

[@ABDULREHMAN-ig7nq]

Hello

[@surendersingh1069]

Bhai die Banwani ha apna mob. No sand kar da

[@nguyenxuanthe3526]

Cho hỏi giá với

[@ChaabaneOuertiou]

Veuillez me contacter

[@raheelahmad8460]

Hi How are you

[@mekanizmalar]

Good, Thank you for asking.

[@raheelahmad8460]

@@mekanizmalar where are you from

[@mekanizmalar]

@@raheelahmad8460, I live in the USA, originally from Turkey.

[@raheelahmad8460]

@@mekanizmalar ok thanks

[@raheelahmad8460]

@@mekanizmalar friends with me

[@spm3060]

Hi~ my name is HJ. I'm a technical sales man for used press machine and NC levelling feeder in Korea. Press machine, feeding machine, milling, lathe, grinding machine, forklift. I handle all press related machines. If you want to import these machines from South Korea, please contact me. I hope to have a good relationship with you someday. Thank you!

[@habibrzayev4100]

Hello. Write me contact for this production machine plz

[@mekanizmalar]

I don't know who made this product and I don't have it somewhere near to me to check it. I purchased it from eBay for a gift to a friend of mine. It was $250 and I consider it as rare opportunity.

[@محمدسعدالدين-و6ز]

مرحبا

[@mekanizmalar]

As-salamu alaykum.

[@DISTRIBUTOR-MESIN]

For detail specifications the machine & PRICE Machine PNEUMATIC PUNCH PRESS TESTER Please Contact VALTEKINDO Thank you

[@praveenagarwal9790]

Please send me your zig zag servo Roll feadar stainless steel coil circle cutting machine video and details

[@tripordjobledeg607]

Cetakan nya full speed boz

[@poroptical]

Sorry, You refer to recycle sheet by casting ??