Portuguese bowline around two anchors with a retraced bight. Used for many applications such as Guying an artificial high directional like the Arizona Vortex and creating an equalizing anchor point
Пікірлер: 23
@69adrummer Жыл бұрын
Damn that's cool!! Well done!!
@markschriever180111 ай бұрын
Great Scott what a knot
@kinnersean6 жыл бұрын
That’s a P-18 you’re tying to, good video.
@uncut125f5 жыл бұрын
A few years ago I remember seeing this video and practicing a lot. Your method is very nice and neat. :)
@jeffm92274 жыл бұрын
Ryan, it would be nice to see some examples of how you can use the retrace loop.
@RockLobster20003 жыл бұрын
Thank you for sharing. I do have a question: when you make the marlin spike do you pass it over both lines? It would help a close up was shown on the key parts.
@uncut125f7 жыл бұрын
this way really helped me a lot
@TormodSteinsholt3 жыл бұрын
Nice vid. I think the last move is called "Yosemite" finish.
@larryborshard78247 жыл бұрын
Hey Ryan- Great video, clear instructions, good job. As before, I'd be concerned about loading the Yosemite finish. Have you pull-tested this enough times for a good sample size to see what the breaking strength is, and where it fails? If it fails along either loop, that common strand may lead to a catastrophic failure. Check with other high angle SAR groups. Please be sure to get some hard data with realistic loads (5-10,000 lb-f) before putting anyone's life on this.
@larryborshard78243 жыл бұрын
@@HollywoodBeachBoy Thanks, Ryan. I always enjoy test data. Unfortunately I didn't see any pull-test diagrams, and it wasn't clear to me where they pulled on the forward-facing loop formed by the double-strand Yosemite finish. I'll give it another read. The Y-finish is typically not loaded on a normal bowline b/c it pulls the knot out of shape. Maybe the extra turns of this Portuguese bowline holds the knot's shape when loadung the Y-finish? Where does the test paper say they loaded the Yosemite? Thanks!
@jeremiahbauman72292 жыл бұрын
@@larryborshard7824 I have the same concerns, what have you found if anything about the testing on this?
@campovertical13883 жыл бұрын
good night very good warrior this anchoring. my question would be about the end of the knot what would be the idea of unloading the knot? strong hug brother
@korpter18175 жыл бұрын
👍
@Perktube15 жыл бұрын
That is one rope-hungry knot.
@trevethan823198417 жыл бұрын
or you could use 2 calibinas and then make the same knot
@emreenhashime11335 жыл бұрын
Thanks u so much sir
@korpter18175 жыл бұрын
굿~~~
@raulhogland73096 жыл бұрын
The camera is too far away. Need close up of what you are doing. :-(
@user-nj7yh3rg3n Жыл бұрын
Сложна
@chds5pyc275 жыл бұрын
Don't be so hard on your own.
@donscott604 жыл бұрын
Terrible video because your hands are blocking the view of the knot while tying it and there should be a zoom in on the knot and the finished knot. You cannot see all the ends and running part of the entire rope while tying the knot because they are near the floor which is not in the video so you're not sure as a viewer where the entire rope is while you're tying the knot
@tdhartman3 жыл бұрын
Easy there, Spielberg; this cat didn't make the damn video so you can bust his chops on camera angles. He was being helpful and demonstrating a simple knot using two anchors. If you require as much clarification as your comment implies; perhaps rope work isn't your calling. Also, you can pause and adjust the video's speed if you start to get fussy or overwhelmed.