POV MazdaSpeed 3 FBO Tuning PULLS

[@akatopj22]

I had a 2013 speed3 fully bolted and tuned made 375 to wheels.Loved the car

[@ColtonRichter]

Nice!

[@gothmommyrecords9830]

@@ColtonRichterwhy did you get rid of this car?

[@G89211]

What did you have done to it?

[@Luck2Skill]

I got a 2008 Mazdaspeed 3 and these are my mods im hitting 22psi it feels insane. Mods Cst5 iwg Turbo XS downpipe & race pipe CPE 3in exhaust Grimmspeed 3 port boost controller CS 3.5 bar map sensor Jbr 3.5" intake CS E85 seal kit 51R battery tray CPE top mount intercooler Forge bypass valve Sparkplugs NGK LTR7IX 1step colder Auto tech hpfp internals

[@ColtonRichter]

Hit 24PSI with that CST5!

[@Luck2Skill]

​@@ColtonRichterI'm trying to get there about to run e-85

[@ajrg91]

I have a 2009 Mazdaspeed 3. What I have done so far is gave it a Corksport Bypass Valve, Corksport SRI, Corksport HPFP internals, NGK Iridium spark plugs, Cobb Accessport, new VVT kit and VVT solenoid, new Camshaft Sensor, installed Trackspec hood louvers to prevent heat soak since it doesn't have the factory hood scoop when I got it. I really should have asked a lot of questions when I bought it, but I was just a big dummy and wasn't knowledgeable about Mazdaspeeds at the time. The next things I will do are Corksport or Cobb front mount intercooler, Corksport coilovers, White Line sway bar kit, BNR S1 turbo, then have it properly tuned in my local shop. I really love this car and I have been putting some blood, sweat, and tears into it. I got it because I wanted to get a 2nd car as a back up just in case something happens to my primary car. It already has some other mods when i got it like a Cobb catback exhaust and some TE 37 type of wheels and lowering springs. I'm treating it as a weekend kind of car or a car to cruise since I already have another car as a daily. I dont really care about big power since I mostly just want something really nice to drive around and to keep for the long term.

[@ColtonRichter]

If you're going the lengths of a turbo, do your downpipe & at least a BNR S3 at minimum

[@ajrg91]

@@ColtonRichter thanks a lot for the advice. If I can remember, my brother in law checked it out and it does have a downpipe installed when I got it.

[@sethjorundson1787]

I have a 2007 Mazdaspeed 3 BC BR coil overs White line front stab links Stainless front brake lines 2017 CX9 GS wheels CS Rear motor mount Damond SSP short shift Serialnine SK5 shift knob CPE3" CAI Intake routed to fender 2.5" TIP Rally Armor mudflats Corksport 28mm rear sway bar JBR rear sway bar brackets/bushings Duel resonator delete Turbo smart bov Cobb V3 stage 2 tune

[@ColtonRichter]

I know exactly what car this is haha

[@sergiovettese2293]

Get rid of that cobb tune and go pd, freektune, dramatuned u wont be disappointed

[@bricegraham8256]

I love speed 3s. Especially first gens for obvious reasons lol. There hella rare in my area. I hardly ever see one out in the wild and its hard to find one on the used market. I'm pretty sure most ended uo in the junk yard from m getting wrecked.

[@TySpears-yi7pz]

I have an 08 with 70,000. Clean title in Oregon

[@bricegraham8256]

@TySpears-yi7pz That's dope but 1, I don't wanna travel way out there, 2 I don't have money saved up to by another vehicle, 3 I'm actually trying to get a larger vehicle and Ima keep my regular Mazda3 for now.

[@Bravdawg21]

Crazy to think of a 3 with 280 like that's crazy! I got the '06 3 S and it's lqughably slow 😂 0-60 in 8.4 when it's cold

[@ColtonRichter]

Mazda definitely made something crazy for the time

[@dkis8730]

I have an 04 3s with a 2.5 swap and it's kinda slow but it does alright. I just need to swap a speed3 trans and then I can turbo it and make some good power...

[@conradwarkentin9872]

I have a completely stock Mazda speed 3 and it makes 450 to the rear wheels

[@ColtonRichter]

no way

[@brandonbaxter7548]

Isn't it Front Wheel?

[@jordantopan1227]

We’ll never know 😂

[@grimlinms3614]

Yeah no you don't

[@akatopj22]

Bro a troll,he said rear wheels.smh

[@rogerbarrett9920]

When you changed gear from 1st to 2nd I heard it crunch !!-- Need to replace Synchro hub and rings - bit of a weak point on higher mileage speeds.

[@ColtonRichter]

They crunched from factory haha, good fluid & new mounts will help!

[@hulkbustersmash73]

Sounds good.

[@ColtonRichter]

Soooo good 😍

[@_dondie_]

Purrr like a sports car.

[@ColtonRichter]

Sure right ✌🏻

[@genecanty3773]

Needing help with my Mazdaspeed3 2007 , it’s got and blow off valve and and intake. Is it worth doing an ungraded stage 2

[@ColtonRichter]

Sure

[@brandonbonillas5158]

Got my first speed3 low compression is cylinder 4 lots of mods but only picked up for $500usd 😅 hope to get on the road again soon!

[@ColtonRichter]

Killer price 👏🏻

[@juulatron1663]

Hey I have a question so I just actually found new seats for my Mazda 3 2008 and the seats are from a 2004 2.3L and are the Red dotted and black ones and I’ve switched them out and they all fit perfectly but I have this odd moment now when the seatbelt is unbuckled the seatbelt warning light isn’t on but when I do buckle it up the light turns on would that be a case of faulty wiring in the seats or is there like wiring differences in the 2004 to 2008

[@juulatron1663]

Sorry if this didn’t make much sense but it doesn’t bother me I’m more just curious onto why

[@danieldt9439]

try asking mazda 3 forums

[@adam4709]

I got a gen2 2011, mostly stock im happy with, but planning some mods atm Has Koni suspension all around Borla catback exhaust Im thinking next is intake, motor mounts, & brake kit

[@ColtonRichter]

🙌🏻

[@justiny2552]

Damond mounts treated me well on both of my speeds.

[@daifaiv]

does it make sense to get mazda 3 bk with 2.0 and 150hp and mod it if im on a budget

[@ColtonRichter]

Sure

[@natewhaley2463]

I got a 2013 tech package fbo and tuned

[@ColtonRichter]

Such a gorgeous spec!

[@CraigYoshimoto-rm9ch]

Yo we should link up. Have a 08 speed 3. Got it a few months ago. In Toronto.

[@ColtonRichter]

On the other side of the country ✌🏻

[@CraigYoshimoto-rm9ch]

@ColtonRichter road trip....lol

[@jroberts3428]

looks fun.

[@ColtonRichter]

Very 👍🏻

[@jerrygobbee6803]

Sweet action. Go pro on the back to catch the flames 😂

[@ColtonRichter]

🔥🔥🔥

[@danieldt9439]

who are you tuned by?

[@ColtonRichter]

This was tuned by Freektune

[@danieldt9439]

@@ColtonRichter thank you

[@danieldt9439]

@@ColtonRichter how long did it take for them to get back to you? was it a e tune? because i’m planning to get one soon just got my catless dp on and was just wondering how long it takes for them to get back to you

[@ColtonRichter]

Depending how busy they are usually a weeks time.

[@noahnel7846]

I have a 2012 gen 2 Garret 3076R Gfb response BOV Mishimoto front mount IC Damond motorsport engine mount ISC coilovers Egr delete E85 fuel system Copper hybrid clutch Short shift plate Solid shifter bushings Access port 4inch KnN intake Custom headers External waste gate + screamer Corksport Stage 2 oil catch can CS injector bushes Grimspeed 3 port boost controller 25 psi boost Stainless exhaust mandrel bent Stock block 😂 #noZZB

[@ColtonRichter]

May all the nonZZB luck rest in your hands my friend haha

[@joelchapple1]

2010 gen poo All motor mounts (dm/cpe stg 2 rmm) 3 inch intake, auto tech fuel pump, bnr s3, catless downpipe, 3 inch cocksport exhaust, front mount intercooler with under-route kit. Tuned by freak tune @ 22psi

[@ColtonRichter]

Gen poo a dog

[@joelchapple1]

@@ColtonRichter bird dog

[@bricegraham8256]

Oh and with that Ive binged watched all the videos frim where I last left off. Lol ima soon have to binge watch your old cringe videos though from when you first started out.

[@ColtonRichter]

You dont need to watch the old ones 😂

[@bricegraham8256]

@@ColtonRichter Lol