Power flex 400 vfd perameter setting

[@marcustyrell4315]

Do you have English version so I can understand?

[@surendrarajput7408]

sir all para meter vfd mai kitne dale jate hai vfd ran karane क liye

[@satendraelectrical5150]

For this drive... 15-20 parameter Dale jate h jo basic program group me aate h... 1. Motor NP volts 2. Motor NP Hz 3. Motor OL current 4. Minimum Frequency 5. Maximum frequency 6. Start source (Auto/manual) 7.Stop mode 8. Speed reference 9. Accel time 10. Decel time 11. Reset to default 12. Auto mode. 13. Motor OL retention. Etc. Apart from this.. Advance program group parameter bhi use hote h.. as per requirement.

[@imranamin2114]

Sr. Grond fult o13 ay raha he ap bta sakty he kis pramitr ka fult he

[@satendraelectrical5150]

Phase U to GND. Check the wiring between the drive and motor. Check motor for grounded phase. Replace F39 Phase V to GND drive if fault cannot be cleared. A PowerFlex AC drive detects a ground fault when the output currents between two phases differ by more than 25% of the drive's rated current.

[@marcustyrell4315]

How do I speed up the rotation on a wipeout wheel?

[@satendraelectrical5150]

Use P38 (Speed source)

[@amarchandchoudhary8870]

Vfd 40 hp power flex 400 me auto rest ho rahi h to usko sahi kesi khiya ja sakthi h

[@satendraelectrical5150]

Change the mode from Auto-reset/run to Non -resettable/ Manual reset.

[@avijit2586]

What is purge frequency in this Drive function

[@avijit2586]

Have any time delay setting in motor Overload setting ?

[@satendraelectrical5150]

Purge command is like a command to takes precedence over a stop command from the common port. The terminal block 5 port is for Digital input ( purge). A purge input starts the drive at a programmable purge speed regardless of the selected start source. In another way we can say that purge can occur and is operational at any time whatever the drive is running or stoped.

[@satendraelectrical5150]

@@avijit2586 yes we can change... Delay time

[@avijit2586]

@@satendraelectrical5150 From which parameter code?

[@abdulkadirshaikh3310]

Undervoltege ka folt 4 ka kya solution he

[@satendraelectrical5150]

For this... Monitor the incoming AC line for low voltage or line power interruption.

[@anilbhogil4983]

How to change motor direction by using keypad..?

[@satendraelectrical5150]

To enable reverse operation, use A166 in program

[@RanjeetKumar-oh4on]

Keypad se chalane ke liye aur pot se connection kar chalane ke liye parameter dalne ke liye

[@satendraelectrical5150]

You can use 0-11 and use code (2) for manual mode.

[@satendraelectrical5150]

And also use terminal at 50 and 55 where we use pot at terminal 50 (+10) and 55 ( common).

[@rajeshdeep2626]

Bro... Fault no 6 motor stalled proplem how solved

[@satendraelectrical5150]

If fault no 6 showing then can do set by perameter A 089 current limit. Increase [Accel Time x] or reduce load so drive output current does not exceeded.

[@shashikapoor6556]

VFD out put voltage nhi aa rahi hai kya Karn ho sakta hai

[@satendraelectrical5150]

Check input connection and Parameters of vtd as per motor.

[@electricallearning8863]

Sir how can we see energy meter reading in this

[@satendraelectrical5150]

Go parameter b015 for drive kWh reading.

[@subhankarroy9147]

UV phase shot fault 41 is showing what to do

[@satendraelectrical5150]

If this showing you can check the motor and drive output terminal wiring for a shorted condition.

[@KundanSingh-ds4dy]

Isko auto manual kese chlaye

[@satendraelectrical5150]

Use parameter P042 ( Auto mode) P036 ( start source) and hand mode command comes from the internal keypad.

[@CarlosDejesus-c6f]

Cómo ponerlo que el amperaje se me vea en la pantalla principal

[@subhashsaini3455]

Motar rpm kasa dala

[@satendraelectrical5150]

Go in program group P032 for motor frequency Hertz, not RPM.

[@shohelloveisendless8417]

Boss tell me how to make PTC connection

[@amarchandchoudhary8870]

Meri ko vfd auto rest honi ki vaja jan na h

[@satendraelectrical5150]

If there are AR-Types faults occur, VFD can auto restart itself.

[@trilokiflstudiomobile7012]

Sar ji fold cold ka bare mein bataiye fault Mein kya-kya code Aata Hai Kiska hai

[@satendraelectrical5150]

There are many faults code with their meaning like.. 1. F2- Auxiliary input 2. F3- power loss 3. F4- Under voltage 4. F5- over voltage 5. F6- motor stalled 6. F7- motor overload 7. F8- heatsink over temp . . . F13 - ground fault F33 to F40 - phase to ground fault F41 to F 43- phase to phase fault F64- drive overload F94- function loss And for more complete fault, check manual..

[@jagadeesh9003]

Useful information

[@satendraelectrical5150]

Thanks 😊

[@Jskdjdmdmz]

PowerFlex 400- How can we Program Unlock A198 , if it is locked on Option 3 , Pls guide

[@satendraelectrical5150]

Use 0 for unlocked in A198.

[@samirmammadov4073]

Dear Friend watched you video how you set up Allen Bradley FLEX 400 You can help me set it up on the compressor Bottarini I was Thankful to you

[@yaakash150]

Very good

[@satendraelectrical5150]

Thanks

[@Mrownerrdxj2837]

Sir powerflex f500 ki user manual koren mein pdf hai to English mein pdf ka link send kar dein

[@satendraelectrical5150]

literature.rockwellautomation.com/idc/groups/literature/documents/um/520-um001_-en-e.pdf

[@behruzhesenov7567]

FOul 122 aşıbka necə düzəltmək olar bilen var

[@girnarspoetry4604]

hi

[@behruzhesenov7567]

Tel nomber ?

[@sonitsahu9060]

Drive 100 set dekar start karne se start ho raha hai aur band ho ja raha hai kya problem ho sakta hai

[@abhaykarmakar8148]

Fault code d004and d003 batya

[@satendraelectrical5150]

Fault code D003 is power loss and D004 is under voltage so for Both Fault code D003 and D004 you can Monitor the incoming AC line for low voltage or line power interruption. If there is incoming power interruption check what problem? May be drive not get proper power supply.