POWER WISARD 1.0 CONVERT TO FG WILSON DCP II GENERATOR STARTING CONTROL

[@caterpillarjhunhunk]

send as any comment about in this video. and subscribe like and share

[@mohmdzeid9526]

good job

[@jumbemkandawire8031]

My Name is jumbe from Zambia,I have liked. Your explanation on the generator wiring. I am asking for the circut diagrams for catapilllar Olympia generator .I asking for two drawings how to change the wiring from power warzad 1.1 to deepsea controller . Your support will be highly appreciated

[@caterpillarjhunhunk]

Contac me in whatsapp [phone]

[@reagandanso5980]

Hello. What about CAN bus connection. Does this controller support it? Or can it work if you don't connect the can bus for a Perkins generator

[@caterpillarjhunhunk]

bro if you do scanning must be the can connected or else,you cannot recieved or get the result on your scanner,and you should scan,by the same software scanner

[@reagandanso5980]

Thank you bro.🙏🏾

[@michaeluravui5758]

Tq Sir

[@caterpillarjhunhunk]

welcome. bro

[@احمدالفاتح-ج9ي]

Hi l have FG Wilson DCP -10 it can’t start when I check it I found two relays ( start & fuel) Start relay has one point 85 ground line is it coming from control Fuel relay has two point 85 & 86 are not coming from control I don’t know why they didn’t come Did the controller spoiled one have something wrong Please help me

[@caterpillarjhunhunk]

about the dcp control, that is negative controled meaning positive is direct,or you can contac me in my whatsapp for better conversation, [phone]

[@balamurugansankaravel9973]

Hi, Could you give the information of Powerwizard 1.0 Battery power supply wire number or terminal ( + and -)?

[@caterpillarjhunhunk]

bro usualy the power supply input is b+ pin # 52 b- is pin#65

[@balamurugansankaravel9973]

@@caterpillarjhunhunk Thanks bro for your response. There is difficult to find the pin number . Is there any number written in the module. ? It is confusing that should I track the cable or pin number ?

[@caterpillarjhunhunk]

yes bro there is numbering on the pin or if the socket is available you can check at there

[@balamurugansankaravel9973]

@@caterpillarjhunhunk yes, I found the pin number. But I couldn't track the cable number. It is written that in the cable 5 controller 65 for negative and 7 controller 52 for positive. Do you know how long duration battery will work with out charging ? Thanks for your response and interest.

[@nigel45212]

hi do you have dcp-10 software?

[@caterpillarjhunhunk]

bro the sorftware you can found it free direct from web site of that controller,you have to make you account free

[@nigel45212]

@@caterpillarjhunhunk what’s the name of the website I can’t find it

[@caterpillarjhunhunk]

bro check the complete spec. of the controller seach it one by one which one will open

[@nigel45212]

@@caterpillarjhunhunk did that and still can’t find it. Checked everything and everywhere

[@nigel45212]

@@caterpillarjhunhunk can you send it to me?

[@dennisducalang3112]

Boss pwede po, ba, Maka hingi diagram NG powerwizard 1.0 control wala kase kami manual. Salamat

[@caterpillarjhunhunk]

wait lang sir ha kakarating ko lang galing s work

[@dennisducalang3112]

@@caterpillarjhunhunk salamat, sir nagka problema kase fg wilson ko na, genset GEP 165-2 wala akong diagram on going PA, kami, troubleshoot...

[@caterpillarjhunhunk]

@@dennisducalang3112 dyan nsir check mo nlang s email mo

[@caterpillarjhunhunk]

@@dennisducalang3112 anu problema genset nyo

[@caterpillarjhunhunk]

@@dennisducalang3112 location mo sir