Practical of Ultrasonic Testing Procedure

Hi Guys,
I am back with another video and this video is on the Ultrasonic testing of welding joints.
If I describe ultrasonic testing in simple words the Ultrasonic testing technology is basically based on the ability of high-frequency oscillations (about 20,000 Hz) to propagate into the metal and be reflected from surface scratches, voids, and other discontinuities. The artificially created and the directed diagnostic wave enters into the tested material and in the case of a defect deviates from its normal propagation. The nature of the defect can be recognized by graphical and parametric readings.
I hope you will like this video and if you like this video then press the like button, share the video and subscribe.
Disclaimer: This video is for information purposes only and it doesn't consist of any sensitive information about any organization.
Thanks ....!!
For further information regarding the ultrasonic testing some details are shared in the links below:-
1.www.alcotec.com...
2.novotest.biz/ca...
3.en.wikipedia.o...
4.www.inspection...

[@appunjaykumar4414]

Well done Mr Arun Sr and ranjeet ..really very nice video and very helpful for upcoming QA/QC engineers .

[@pk143realvoice]

Superb ut scanned 👌

[@ahshanhussain1499]

Agar job thickness Mera 8mm se Kam hoga to jab repair ayega usme ut krne ka kya cretia hai asme section 5 me ut karna padega ya jarurat nhi hai please reply

[@shilpisaha1309]

Nice video

[@kkhpathan]

Mistakes during UT overlapping and scanning speed

[@manoeljoventinodossantosju4060]

Top

[@deepakpandey9350]

Where is DAC , First mark half n full skip distance Then check lamination then go for scanning. .

[@anandhubaburaj2995]

Sprrr

[@allwinthivan6795]

Sir, pipe thickness 6.4 mm, dia 4".ut testing half skip catch one defect sir, but defect beam bath full beambath is coming, why is this happening, sir 70 degree probe use sir true angle 69 degree, but defect half skip and depth ok sir but beam bath only high full beam bath coming sir. Why sir. Please tell me sir

[@Fab.NDT.Solutions]

Scanning is too poor, AWS not recommend 8x9 mm size probe. UT technician is not well

[@sathiyavelan5705]

Very useful video sir. Please upload more video

[@josefuentes4945]

Scan pattern aren’t overlapping, could use some improvement

[@justinj2505]

Sir, When scanning a weld in 10mm plate using 45degree probe. Range is 125. Machine shows SP=43.5, SD=30.7,D= 30.7. How can I calculate where is deffect??? Sir please help..

[@wbshow1553]

45 degree probe for job thickness above 45 mm

[@venkatalokesh1555]

How much overlap you taken , too blender mistake you did probe scanning movement is very poor , please scan 10%overlap i.e and one thing you must scan 100mm skip distance you doing 50mm skip distance only , and probe scanning speed 150mm/sec only you are doing too fast . So please be careful about scanning .

[@ritzwebceo529]

Interesting VIDEO! One candidate (UT LEVEL2)I would like to join in as UT inspector kindly give me a feed back

[@thearunvlogger2404]

How can I help you?

[@dinho9492]

Where is your DAC bro?

[@yashgamers9608]

This is AWS bro 😂 in AWS no DAC curve reference dB is only going to calibrate and scanning dB need to set as per sound path

[@lucknowboy4442]

Scanning karne nahi aa raha hai bhai apko

[@saklainmustak273]

Hallo sir is joints me UT ka kon sa acceptance criteria use hoga

[@yashgamers9608]

AWS D1.1

[@niteshpanditnk441]

Probe to achhe she chalawoo 😅😅😅

[@Yarki18]

Ye welding galat procedure se weld Kiya yai..... flange and web Ka joint in line (ek line )weld nhi hota

[@mubasshirshaikh6942]

Mujhe qc engineering ka number chahiye

[@rehanraza5423]

Scanning was not good