This is by far the most understandable explanation on this subject I have found so far. One thing to mention (you do so in a follow-up video, but I don't think it is here): this works on a dual supply op-amp, at least the negative rail needs to be able to get down to the Vf of the diode (I got all weird results with my LM358 connected to V+ and GND, but as a result I learned a lot). Thanks for this great video!
@Kochu7153 жыл бұрын
I ran into the same problem during a simulation. Thanks for an excellent analysis and explanation of the behaviour of the circuit.
@bloguetronica6 жыл бұрын
This is very useful. That "super-diode" circuit with a single diode is often shown as being correct, but the big mistake here is that the reverse-biased diode will open the feedback loop, and the op-amp might even misbehave if one of the inputs is out of the common-mode or differential mode range. Also, a too high impedance in the negative feedback loop is always a problem, and should be avoided at all costs, because the op-amp might oscillate (even if it apparently doesn't have any kind of positive feedback).
@overkillaudioinc4 жыл бұрын
This has been EXTREMELY helpful!!! Very well explained. Thank you.
@col03427 ай бұрын
Note: one doesn't absolutely need precision resistors - 1 trimpot used in the feedback loop of the rectifier opamp *or* one trimpot to adjust the input weights into the inverting adder is enough to balance out any error in the other resistor pair.
@Atlas_Enderium2 жыл бұрын
Wow what a great explanation. When you explained the use of the summation amp to make it a full wave rectifier, it immediately clicked in my head “oh duh” 😂
@RupertHandford8 жыл бұрын
Thanks for sharing another excellent tutorial.
@samshurp45183 жыл бұрын
At the end of the video, you explained about full wave rectifier but how does load affect the signal in the full wave rectifier?
@koshka0210 ай бұрын
why can't any of my profs just fucking say this. Good lord you make this easy. Well done.
@jimstand8 жыл бұрын
Thanks for taking the time to do this video. It is very educational.
@DreitTheDarkDragon8 жыл бұрын
Frequency doubling of triangle wave...wow, that's nice trick! :)
@dinazul233 Жыл бұрын
Can you please tell me which book is it? Thank you so much for your explaination 🙏👑
@kvsaiakhil34906 жыл бұрын
That was a very clear explanation....Thank You for the effort!!!! Loved it
@cfavreau2 жыл бұрын
Thanks for making this video. It is helping me to troubleshoot my own implementation which I am using a virtual ground.
@shirazsohail2 жыл бұрын
Great explanation with practical demonstration. Which book you are referring in the video. Can you provide the book details. Also some suggested reading materials for experiment engineers.
@explorerpragun4312 жыл бұрын
Very useful And well explained sir
@Hephaestus5124 жыл бұрын
Very good video. Exactly the information I was looking for.
@voice4voicelessKrzysiek9 ай бұрын
Excellent! Thank you.
@christopherjones56517 жыл бұрын
Can't thank you enough for this video, brilliantly explained and super super helpful.
@LookNotDo7 жыл бұрын
What is the name of this book? Or what books you could recommend for better understanding of analog circuits?
@huskialn20082 жыл бұрын
You find out what is the name of the book?
@paulopecegueiro16942 жыл бұрын
@@huskialn2008 did you?
@fulvioportalupi528 Жыл бұрын
the book is by J.Graeme: applications of operational amplifiers
@OluwasegunLawal-bx2ww Жыл бұрын
@devttys0 can you please list the textbook you're using in the video?
@mukun8an3 жыл бұрын
Superb explanation. Thank you very much. TC.
@syedhasan13427 жыл бұрын
Awesome Explanation! keep up the good work.
@codebeat41922 жыл бұрын
The drawing is different comparing to the schematic in the book. There is only one input connection at the beginning of the circuit. Where to connect the other wire, to ground? Same on the output.
@aussiegruber863 жыл бұрын
Thanks for the well spoken demonstration ;-)
@whiley2k107 жыл бұрын
This is great thanks! You made this very easy to grasp! I also like to see some practical examples of the results so thanks for that also.
@nuradhim977 ай бұрын
Do you have suggestion what op amp ic that perform good with this circuit?
@Enigma7583 жыл бұрын
At 10:10, why did the diodes flip direction?
@TecKonstantin8 жыл бұрын
you should show a op amp rectifier circuits witch uses only one Op and only like 5 resistors, to make it also very useful it only works on single rail supply which is very handy. This is interesting for Applications with a single rail supply, like in Sensors etc. one disadvantage is that the output is only 1/2 of an Ideal full way rectifier, if u are interested i can tell you i don't think it is a common known circuit, nice vid btw!
@Analogzoo8 жыл бұрын
+TecKonstantin Sounds interesting, I'd love to see a schematic!
@wisnudjatmiko3 жыл бұрын
very clear explanation👍👍👍
@SomeRandomPerson1636 жыл бұрын
Great video, I'am interested in that topic. So did we lost precision because R and R/2 resistors have not exactly values?
@Analogzoo5 жыл бұрын
Correct, mis-matches in the resistor ratios will cause error in the rectified output, as will imperfections in the op amp itself, such as input voltage offset errors.
@barbaraesterlen25807 жыл бұрын
Good enough to pass this test! Thanks!
@ramiro78786 жыл бұрын
Thanks for the video! At some point you said the fully rectified wave has double the original frequency. That's very interesting! I was looking for some way of obtaining half the frequency, maybe rectifying two halves up followed by two halves down. I think I would need some sort of memory trigger. Would you have some hint on how to achieve that?
@Analogzoo6 жыл бұрын
The easiest way to divide the frequency of a signal by 2 is with a flip-flop: kzbin.info/www/bejne/hX2YY5ljoJicf6cm28s . The output will be a square wave, so if you need a sine wave output, this would have to be low-pass filtered to remove the higher frequency content of the square wave.
@marinhopduarte8 жыл бұрын
Great explanation! Thanks a lot!
@davidbear19618 жыл бұрын
What is the book that you are teaching from?
@Analogzoo8 жыл бұрын
+davidbear1961 "Applications of Operational Amplifiers, 3rd Generation Techniques", by Jerald G. Graeme (Burr-Brown). It's an oldie, but a goodie; out of print unfortunately, but available as a PDF on archive.org: archive.org/details/ApplicationsOfOperationalAmplifiers-3rdGenerationTechniques
Thank you. Great explanation especially with the screwdriver in your hand :D
@shubhamdubey35856 жыл бұрын
Very nicely explained
@shemkalele3 жыл бұрын
Great video, really helped!
@asciisynth6 жыл бұрын
Brilliant, this video really helped!
@joelmathews39347 жыл бұрын
so r1 and r2 becomes parallel with load resistor and forms a volt divider.r1 and r2 are in series since no current goes to i/p terminal of opamp . right?? NICE VIDEO
@user-ik9ig4mz3r4 жыл бұрын
If i have very low signal below the forward biased voltage of diode , can this configuartion rectify it with unity gain ? Or should i increase the gain then rectify it ?
@cristopherenriquenodagarci24138 жыл бұрын
Dude great explanation!! Thumb up :)
@friedmule54035 жыл бұрын
Really great video, thanks for sharing:-) I hope that you'll please answer my noob question. To me it sounds like you have 2V peak to peak as AC input and 1V DC peak. Does that not mean that you loose 1 volt while rectifying?
@paulcohen15553 жыл бұрын
AGAIN: What is the name of the book?
@davidluther39555 жыл бұрын
GOOD EXPLANATION.
@user-vl6cy1gw2v4 жыл бұрын
Nice. very good. what is the name of the book. and if you know a full wave rectifier with out diode and by op amps and can explained in tueb. thenk you a very mach.
@shawnmicheals18658 жыл бұрын
Hi !ggreat video ! can you list some of disadvantages of this FWR circuit. thanks for reading!
@Analogzoo8 жыл бұрын
+Shawn Micheals Well it's a split supply design, which is usually undesirable for simplicity / low voltage operation. The circuit's primary performance disadvantage is that the slew rate of the op amp limits its frequency response. An alternative circuit that uses an op amp and a comparator helps to overcome both of these drawbacks: kzbin.info/www/bejne/Z4Wvi3WNrZt1ecU
@conto70323 жыл бұрын
I am little late to the party, but can somebody send me a name of the book in the video ?
@215alessio6 жыл бұрын
what if you use twoo opamps in parallel but one will use the non inverting input the sum of both in the output would be a fully rectified sinus to (just 2 cheap diodes extra to use)
@Analogzoo6 жыл бұрын
You could do that, but you'd lose a diode of voltage on the output; if you're dealing with smaller signals, the diodes won't even turn on. Even if you're dealing with larger signals, the actual voltage drop across a diode is not precisely controlled, so you'd lose precision.
@beakytwitch79052 жыл бұрын
Diode 2 is the wrong way around, surely ?
@ZoulXHD3 жыл бұрын
mvp whered u get that screwdriver from?! i love it
@smudgerdave11418 жыл бұрын
Nice analysis. However 1:17 "passive diodes" are not passive. All semiconductors are active components by convention. HTH
@Analogzoo8 жыл бұрын
+Smudger Dave Concurred, "passive" was a poor choice of words in an attempt to distinguish rectifiers that use amplifiers from those that don't.
@voyasart4 жыл бұрын
beautiful.
@elluisito0004 жыл бұрын
Hi! Nice vid, and scope too :D
@davidbernfeld26098 жыл бұрын
Hi! Great video! Just discovered your channel it's great. I tried this circuit with a friend. The inverting half wave rectifier (in blue) seems to saturate 1.5V before reaching V-, even with a rail to rail OPamp. Is there a way to obtain such a swing? Maybe with your other circuit using a comparator and a relay? Thanks for reading.
@Analogzoo8 жыл бұрын
+David Bernfeld Are you trying to run this circuit from a single supply? It's meant to be used with a dual supply; the rectifier circuit from my other video is a better choice for single supply operation. With that said, I'm not sure how a rail-to-rail op amp could be saturated if its output is 1.5V above V-? Could you provide some more details on your circuit and what you're seeing on the scope?
@davidbernfeld26098 жыл бұрын
Thanks for the reply! It was in deed a single supply configuration. However, we did create a Vmid=Vcc/2 with 2 resistors and a buffer. The circuit should work exactly the same or are we missing something? We can't get closser to V- than 2 diode voltage drops. We tried your other circuit, works LIKE A CHARM! Thanks!
@MohammedAyazQuadri2 жыл бұрын
Awesome! What's that book btw?
@taojiang7196 жыл бұрын
awesome, thanks
@ridiculous_8 жыл бұрын
do i miss something? do you mean the half wave rectifier only suit for low resistance load? as the signal will have direct voltage division to the ouput
@Analogzoo8 жыл бұрын
If you want half wave rectification with only one op amp and one diode as initially shown in the video, then yes, your load has to be much smaller than the series combination of R1 and R2. However, as shown at 7:56, the addition of a second diode fixes that particular issue, and you will get proper half wave rectification with both high and low resistance loads.
@ridiculous_8 жыл бұрын
devttys0 but i confuse that how does the addition of diode can fix the issue? there is still path along R2 and to the output
@Analogzoo8 жыл бұрын
With the second diode in place the op amp can hold its inverting input at ground, since that diode is forward biased once the op amp's output drives ~0.6v negative. This makes the junction of R1 and R2 effectively grounded.
@ridiculous_8 жыл бұрын
Oh,understood!!! thank you very much!!!
@joelmathews39347 жыл бұрын
+devttys0 but its already grounded by virtual ground concept.right?
@PlasmaHH8 жыл бұрын
Could you maybe use something plastic to point to the scope? The screwdriver makes my hairs stand up ;)
@bigalexdotit7 жыл бұрын
yeah, using the screwdriver as a pointer was just so cool lol! :)
@akashwayal87975 жыл бұрын
Best explanation 👍👍 thanks
@addams_746 жыл бұрын
Hi! What model was used Op Amp? What are the resistor values?
@Analogzoo6 жыл бұрын
The resistor values at the frequencies typically used for this type of application aren't critical and are usually selected based on your desired input impedance for the circuit. Opamp selection is usually based on your requirements for the circuit; higher frequency signals will obviously need a faster op amp. For the examples here, IIRC, I used MCP601/602 op amps and 10K ohm resistors.
@jpmorgan1876 жыл бұрын
What's a practical use of a precision rectifier?
@Analogzoo6 жыл бұрын
One common application is in the feedback loop of an automatic level control or automatic gain control circuit, say for an audio amplifier. By rectifying the audio signal, it is easy to detect the peak voltage of the signal and adjust the gain of the amplifier either up or down in order to maintain a constant amplitude output from the amplifier.
@jpmorgan1876 жыл бұрын
interesting, thank you. appreciate the cool videos.
Can you give me the name of that book you were using please?
@Analogzoo8 жыл бұрын
+Josh Adams "Applications of Operational Amplifiers, Third-Generation Techniques": archive.org/details/ApplicationsOfOperationalAmplifiers-3rdGenerationTechniques
@joshadams78398 жыл бұрын
+devttys0 Thanks!
@yurisnaker8 жыл бұрын
and the power supply ?
@Analogzoo8 жыл бұрын
+Yuri Novais Araujo The circuits in this video are designed to be used with dual supplies (e.g., +-10V). I have another video on single supply rectifier circuits here: kzbin.info/www/bejne/Z4Wvi3WNrZt1ecU
@mdsouravkhan737410 ай бұрын
Book name please
@kashivissu73086 жыл бұрын
can you please upload a video for "precision ac to dc converter using op amp"