How to replace a graphic on the budget roller banner stand. Stand and replacement graphics available at www.printdesigns.com
Пікірлер: 41
@ElormBeenie12 сағат бұрын
Thanks for this video. Just have me an easy way out😇🙏🏾
@chukanwosu747810 ай бұрын
This is simply explained and well understood. Thank you. This is of great assistance.
@poseyparks369310 күн бұрын
My sign snapped from the top. I should be able reattach. Thank you so much.
@achotshering4614 Жыл бұрын
That was simple and great information I needed!! Thank you! 👍
@tkbradford12472 жыл бұрын
Thank you. This was perfect information. I am above average handy, so I shouldn’t have any problems with this. I just wasn’t sure how it would attach on the bottom, and your video explained it in great detail.
@PrintdesignsLTD2 жыл бұрын
No problem, i'm glad the video was useful. You will need to use a strong double sided tape to attach the print. After sticking the print to the stand you can over-tape the join between the graphic and the stand with parcel tape. This will make the join more secure!
@danielwalker46254 жыл бұрын
I like this edit!!
@anantasakrattanasopa19795 ай бұрын
Great job!! Thank you very much.
@marcosfurukawa11042 ай бұрын
!1. Excelente vídeo! Muito bem explicado e informativo.
@IanRuben4 жыл бұрын
what happens if the pin was pulled out prematurely and all the spring got inside of the bottom part is there a way to repair this issue? thank you
@MarkThompsonUK4 жыл бұрын
If you pulled the pin prior to attaching the print (with the top rail in place) then the spring inside will lose tension. It can be fixed but it is fiddly. Attach the print with the top rail on, then remove the screws that hold the end plate on the stand. Do this on the side of the banner that has the flat part of the spindle protruding from it, not the other side that has a round spindle protruding from it. With the screws undone, turn the end plate round and round whilst keeping the flat part of the spindle in the slot on the side of the banner casing. This is tricky! After about 20-25 turns the print should be wound inside. Now put the screws back in.
@mattjarrels4594 Жыл бұрын
Thanks for the info! This helped me out at work
@PrintdesignsLTD Жыл бұрын
No worries Matt, glad the video was useful! Best wishes www.pintdesigns.com
@jeromeclausdritchz35953 жыл бұрын
THANK YOU
@MS-uz4ix Жыл бұрын
Accidentally pulled the pin and the spring on the roller unwound. Any tips on rewinding the roller to get back to the original tension?
@PrintdesignsLTD Жыл бұрын
Whoops! sorry to hear about this. The banner can be fixed but it's a fiddly process. The first thing you need to do it remove the screws from the end plate of the stand that has the flat spindle protruding from it. With the screws removed you can rotate the end plate of the stand clockwise while it is held flush to the casing of the stand. The flat head of the spindle should be still poking through the slot when you rotate the end plate. Be careful here because as you rotate the end plate with the spindle poking through the slot, the tension on the spring increases inside the stand. It is easy to accidentally pull the end plate away whereby the spindle will pop out of the slot and 'lose' all of the tension. Also be very careful that the end plate does not fly out of your hands whilst turning it or you could hurt yourself! We wear gloves and safety goggles when doing this. You need to give this end plate about 20-25 turns after which the print should be wound back into the stand. Once the print is wound in, put the screws back onto the end plate to secure it. Again, be careful that you don't pull the end plate away from the stand and allow the spindle to pop out of it's slot while doing this or you will need to start over! I hope this helps and good luck.
@MS-uz4ix Жыл бұрын
Thank you!
@justrightinvites561911 ай бұрын
thank you
@Ayzprella8 ай бұрын
thank you for your video
@PrintdesignsLTD8 ай бұрын
No worries, I'm glad it was useful to you. All the best www.printdesigns.com
@deydagaraycoa5499 Жыл бұрын
do you know what can I use if the locking pin is missing?
@PrintdesignsLTD Жыл бұрын
You could use a small nail, a matchstick or cocktail stick or a small allen/hex key
@MichelL-lv4fp Жыл бұрын
What kind of tape should I use?
@PrintdesignsLTD Жыл бұрын
Hi, you should use a good quality permanent adhesive tape. We use 50mm tesa 4965. It works well for us based on the printing materials we apply to roller banner stands at www.printdesigns.com but you should test adhesion to the particular print material you are using to make sure it holds OK!
@timtuff10113 жыл бұрын
I have a banner like this that was installed backwards - the print side faces the pole. Can I unscrew the side panels and reverse the roll entirely? Or do I need to return to the banner company?
@PrintdesignsLTD3 жыл бұрын
Hi Tim, the print would need to be removed and refitted in this case. You should contact the company who you ordered it from and ask them to collect the banner and replace it!
@kerryoreilly93082 жыл бұрын
Thank you. This fix worked!
@moneisblessed949520 сағат бұрын
The locking pin that came with my banner stand doesn’t fit inside the hole on the side! Now what do I do? 😖
@PrintdesignsLTD5 сағат бұрын
Hi, On your banner stand there will be an outer hole on the casing and a hole on the spindle inside the roller banner. When you put the pin through the outer hole, it has to line up with the hole on the inside for the pin to push into place. You will need to pull the banner up and down so the spindle inside the banner stand rotates and the two holes line up. Try pushing on the pin whilst you pull the banner up and down and you might find the pin locates correctly. If the pin you have is too big to go through the hole, you can use something smaller such as a small Allen/hex key, a nail or possibly even a cocktail stick. I hope this helps! Best wishes www.printdesigns.com
@hemmoband329 Жыл бұрын
what if you dont have any tools?
@PrintdesignsLTD Жыл бұрын
What tools do you need?
@tedfrazier95869 ай бұрын
Thank you
@PrintdesignsLTD9 ай бұрын
No worries at all. Glad the video was useful. Best wishes www.printdesigns.com
@dps2532 жыл бұрын
Where do I get the pin?
@ajlavilla2 жыл бұрын
I think it comes with the stand
@PrintdesignsLTD Жыл бұрын
When we send out replacement graphics for roller banner stands, we normally supply a locking pin. It's worth noting that if you don't have a specific locking pin, you can use something similar instead. A small nail or hex key should do the job!
@abdelkebirtaghia36903 ай бұрын
شكرا جزيلا
@ganeshbop84555 ай бұрын
Woow great
@PrintdesignsLTD5 ай бұрын
Glad you found the video useful :-)
@waraubie693 жыл бұрын
Great video but could you put a towel down next time? 😱