PRO-TEC EN | Combustion chamber cleaning without dismantling | Carbon X

Restore your engine: PRO-TEC Carbon X
- Effective combustion chamber cleaning without dismantling
- Causes quiet engine running, constant performance, minimal fuel consumption and low emissions
Read more: bit.ly/2oRpu6J

[@XXXXLance]

One mistake - the cylinder 1 and 4 is dirty becouse the valves were open, so that dirt from intake valve got inside the chamber and accumulated (making impression that it is more dirty while actually it was a dirt from the valve). What you should do is repeat the process with 2 and 3 valves open.

[@Radiateprosperity]

Your website does not have the product advertised. Can u post a link in your bio???

[@federicotorresbordils7624]

What about the openned valves, may the product pour throughout the intake or exhaust mainfolds, is it dangerous? Thanks BimmerN53

[@bluechemGROUP]

Hi Federico! We even recomment the valve overlap to ensure the cleaning foam reaches the upper side of the valves as well. By using K2 all the foam is dissolved microscopically. This emulsion can be sucked up with the extractor. So nothing can happen. We strongly advise you to follow the instructions in the manual carefully. Hope this was helpful! regards Willy

[@rocnikrocnik]

Ještě prosím vyndat písty a zkontrolovat neporušenost jejich boční stěny, jestli chemie nesetřela matný nátisk, který při chodu motoru funguje jako privaděč oleje k p. kroužkům. A vysvětlit, jak přinutíte automechanika k časové a technologické kázni a aby si spreje neponechal pro svou potřebu a do zákazníkova motoru nenalil levnější Dimexid bez odsávání?Děkuji.

[@bluechemGROUP]

Hello ročnik62, it would be easier for us to answer you, when you frame your question in english. Thanks. :) Best regards, Your bluechemGROUP-Team!

[@Swift4Ghz]

Where can I get PRO-TEC Carbon X in Moscow, Russia?

[@bluechemGROUP]

Please contact our russian partner Forz LLC pro-tec-russia.com/

[@Swift4Ghz]

What is the title of this track? Please :)

[@Swift4Ghz]

Nice track)

[@bluechemGROUP]

Hi Swift4Ghz, please excuse the very late answer. Your message has been lost 😬 To answer your question: That track was made available by an agency - so own created... 🤷‍♂️

[@husamothman1]

Do you have this service in Dubai, United Arab Emirates?

[@bluechemGROUP]

Our Distributor for Dubai is MBS Automotive General Trading L.L.C You can find the contact details on our website: www.bluechemgroup.com/en/international/ >Middle East>UAE

[@MbellaLouna]

Do you have a dealer in Tunisia ? Seems the one in Monastir ..its website is alway down. Please provide a full list of your products' dealers in Tunisia

[@danarsurchi9098]

How can I get this product from Iraq

[@Zattoo20]

Ich hab Späne vom Turbo im Brennraum, gibts jemadnen aus Berlin der das machen kann ?

[@bluechemGROUP]

Hi Zattoo20, frag hier mal nach: Kfz Thomas Sommer Dorfstraße 3 16341 Panketal

i don't understand how this product can clean intake valves, air intake, egr and turbo when you spray this just on the pistons.

[@spiderman19901990]

This is how. You just spray it into the intake valves and do the exact same process. But you need to take the intake manifold for this. Plan on doing it this weekend. Application in EGR, Turbocharger and Intake Manifold The application can be carried out in the mounted and disassembled state. This is dependent on the accessibility. Disconnect the inlet and outlet lines from the EGR valve or the turbocharger, or open the intake manifold between the air filter box and the throttle valve. Spray cleaning component K1 into all areas. As soon as foam escapes from all access openings, stop spraying and let it react for approx. 15-20 minutes. Dissolve the cleaning foam with K2. For this purpose, rinse the EGR valve, the turbocharger or the intake line several times with the component K2. After assembling the parts, a test run of at least 20 minutes is required.

[@joker8541]

Fake this product

[@user-hj1fk1vz7k]

здравствуйте. в России где можно купить данный препарат?

[@47ALTAIR47]

Этот чувак по ходу не знает что декоративную крышку мотора TSI нужно защелкивать нажатием, а не просто ложить на мотор kzbin.info/www/bejne/qoDZYZhtrcx6qcU XDDDDDDDDDDDDDDDDDD