Proctor Compaction Test

[@andrewdiedrich3097]

I know its been 8 years but you manage to explain this stuff SOO much better than our lab books.

[@JSSTyger]

You can run what is called a one-point test. You need the proctor mold, a hammer, a strike off bar, a portable stove (to burn off the moisture), a sieve, a brass bowl, a scoop, and a balance. You can perform the proctor test as shown in this video on site. It will yield one moisture content and one bulk unit weight. Your state DOT should have typical moisture-density curves. You simply plot your data on the chart they provide.

[@mahnoorfatima5761]

I think at 3:20, they meant to show the graph of dry density vs moisture content rather than the particle size distribution.

[@engineeringknowledge5709]

this man talks as he will burst into laugh ... ..

[@anshulmehta1603]

I couldnt see this video without grinning now

[@ruidioheadbebop3755]

4:42 the equation might be wrong, the moisture content defined for Geotechnical Engineering has denominator of dry mass not wet mass. Obviously, at 4:42 what will be multiplied with moisture content difference is wet mass.

[@BracaPhoto]

Best way to remove all the dirt from the mold before weighing is to SPIN IT 👍👍😎😎 The motion flings the dirt of without affecting your soil inside the mold

[@jimmy_flaps]

Or spray the inside with a lubricant like WD40 before adding any soil

[@BracaPhoto]

@@jimmy_flaps you add wd40 ? Is that too get the soil out after weighing? I haven't tried that

[@BracaPhoto]

@@jimmy_flaps some clays are stubborn as hell though

[@MartinRodriguez-cu6vl]

​​​​@@BracaPhoto we do that at my lab, spray the inside of the mold with WD-40, unless the sample is really wet and will slide right out. I usually just cut away the outer edge of the sample after so I don't include any WD-40 in my moisture

[@sadmanhafizsiam9604]

Thank you it helped me after 8 years latter....😊😊

[@Owosenisegun]

You are doing well Well done

[@samuelmeta2546]

thank you so much for your clear explanations. can you please do another tutorial clip on California Bearing Ratio (CBR) test?

[@hoggy20]

I'd like to see you doing a 4.5kg rammer compaction in a cbr mould PMSL.

[@lightfdar]

Awesome video, thanks for the upload.

[@teerayutjatupalung5221]

ดีมาก คนไทยดูให้มากๆๆๆ นี้คือการทดสอบวัสดุงานดินของโครงสร้างทางโดยการหาควานหนาแน่นสูงสุดที่ความชื่นเหมาะสมเป็นการทดสอบในห้องทดลองและจะนำค่าที่ได้ไปเทียบกับหน้างาน

[@GeotechLab]

The compaction curve was misplaced by a particle size distribution at 3:18

[@akhilnarvaneni1555]

YES

[@678JuliaC]

Thank you! This is an excellent explanation.

[@MrNabaz1981]

This is very helpful. Thank you!

[@OffbeatDrill]

Dr. Dove brought me here

[@caydenthompson126]

Thank you very much sir! You really helped me with my school assignments and presentation.

[@96freeshz]

Well made video.

[@ronaluna]

search on google moisture content soils. several construction material testing outfits sell some kits (Speedy 2000), but are expensive (search Humboldt or Elle combined with the word soil. The agriculture industry has some devices for purpose of crops. good luck!

[@sajharguru]

Very helpful video 👍❤️☺️

[@yashkamal6395]

Excellent video.

[@Sam-cy5rm]

1:00 That guy in the back was thirsty

[@Sam-cy5rm]

10:01 I guess they like Diet Coke LMAOOOO

[@TimothyMoananu]

Great video

[@ruymenezes4940]

how many proctor tests is he able to do per day?

[@heydude76]

where can I get a moisture tester, I own a mini excavator with hydraulic compactor and I would love to have a moisture test and the data sheet that tells me what good moisture levels are for sand, pit run, road gravel, and other mysterious form of soil, i believe the equipment is out there and it wont be the perfect thing but it will give me an idea of how my compaction is working and i will be sure to pass tests I feel bad when I fail a compaction test feels like a waist of time

[@akhilnarvaneni1555]

did you found it??

[@niteshchaturvedi1544]

You look like sheldon cooper....

[@jayinla228]

Do you have the ASTM that's directs how to collect the soul sample?

[@rajeshbanchhor3461]

बहुत ही उपयोगी और महत्वपूर्ण प्रयोगशाला जानकारी के लिए धन्यवाद.

[@avichaidarshan6468]

Hey, your videos are great can You make video... california (C.B.R.) test ?

[@KevanRice]

Kevans a maddientust

[@ryanshi1365]

good job

[@MattJBowman]

question? how important is breaking up the clumps when doing the moisture test?

[@MartinRodriguez-cu6vl]

If you're just breaking it up before sticking it in the oven, it helps facilitate the drying process. Bigger chunks usually take longer to dry.

[@MohdRuslanMuda]

@@MartinRodriguez-cu6vl why not wearing gloves because bare hand will disturb the accuracy of sample moisture content.

[@emmanuelogbaide1905]

Is it possible to compact sharp sand with standard compaction method in the lab

[@kaviyaj3809]

good and useful

[@yaregalmengistie]

thank you a million sir.

[@sabahbenchaib969]

what do we call IPI index (indice portant immédiat) in english?

[@juniorcletus-zg7fn]

Great

[@rahulpoudel9463]

Top hanne hola ni aba

[@shahbazalisangrasi8576]

well explained.

[@Nediler]

i do a lot of 6" ASTM modified C proctors. lots of 1" rd base where im at

[@regine12]

Thank you

[@gnidnoeled786]

Hi Sir. There are six red "X" marks in your graph, does this mean you did the process six times to get six dry unit weights and six moisture contents values? In other words you did six trials?

[@monkeyfoot5377]

Yes, 6 specimens at different moisture percentages, getting your moisture content each time as well. Then charting your curve

[@omarmetwally4205]

تسلم ياسطه

[@mohamedfathimoussa1732]

+Omar Metwally تسلم ياسطى وربنا احنا علينا حاجات ياخى :)

[@jorgegomez5512]

When to use the modified and when the standard ??

[@steviemack212]

Jorge Gómez typically a clay material is standard and granular is modified

[@MartinRodriguez-cu6vl]

The testing method should be specified before you even start testing, that's not on you. Either get it from the project manager, the engineer, the contractor.

[@ismrussy7967]

How about Flow Table test ???

[@palithadegambada6263]

very important test in feild

[@mohamedmachiri287]

love it

[@mohanannair.a.p8929]

thanks

[@brijjoshi98]

good

[@youceflakehal6275]

Thanks

[@ruymenezes9799]

01:00 it's possible to see a person reflection behind him

[@Loveyamellows]

drinking diet coke

[@davidciolino3516]

Lol. I'm taking my field evaluation test next week. And I have to run a compaction test. I ran a few before. Still a little sketchy about it. Lol. We have to run a 3 point curve. 2 on dry and 1 on wet. Lol. Hopefully I pass.

[@akhilnarvaneni1555]

good😃

[@tugberkkayihan6092]

10.02 coca cola commercial

[@አንዲትኢትዮጵያ]

Sir!Thanks for ur presentation. I would like ask some thing. How can I construct plasticity chart (Especially A-line & U-line) using excel. Then if you have tutorial video or link pls. Thanks for support

[@forrestercook8177]

How lazy are you?

[@Liam2173]

I am not really nitpicking here but doing a proctor in the Lab is different than doing it in the field. I test soils and in the field. It's different when doing a one point in the field than it is on the lab. Rock correction is needed as well Also we have to use a speedy for the moisture content as well. Also it's hard when u have some pissed off contractors city state inspectors watching I the whole time when doing this. Good video but lab and field is different

[@idoumouamar5304]

c'est bien lorsqu'il est traduire en français

[@hemasaberhemasaber4042]

Where is the beautiful blonde girl

[@volgger123]

watching from mars any one from jupiter ? visit NNNNNNNNNNEEEEEEEEEPPPPPAAAAAALLLLL (Nepal )

[@breinerxcamilo]

Thanks. (Y)

[@anissofia7058]

aku takleh la tengok video ni. dia suka tengok orang tepi camera and aku distracted!!!

[@swipa___thefox1848]

W rizz

[@bekaluterefe7533]

Moisture condition value

[@bekaluterefe7533]

Determination of moisture value

[@heydude76]

waste

[@akmaldurrani4616]

this curve is irrelevant

[@asifmaniyar4152]

Great video

[@bakhtiareng.6392]

thanks